LX1974IBC

LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET DESCRIPTION KEY FEATURES Near Human Eye Spectral Response Very Low IR Sensitivity Highly Accurate & Repeatable Output Current vs. Light Scalable Output Voltage Temperature Stable Integrated High Gain Photo Current Amplifiers No Optical Filters Needed APPLICATIONS The LX1974 is a low cost silicon light sensor with spectral response that closely emulates the human eye. Patented circuitry produces peak spectral response at 520nm, with IR response less than ±5%, of the peak response, above 900nm. The photo sensor is a PIN diode array with a linear, accurate, and very repeatable current transfer function. High gain current mirrors on the chip multiply the PIN diode photo-current to a sensitivity level that can be voltage scaled with a standard value external resistor. Output current from this simple to use two-pin device can be used directly or converted to a voltage by placing it in series with a single resistor at either of its two pins. Dynamic range is determined by the resistors (typically in the range of 10K to 100K) and power supply values. Typically the LX1974 needs only 1.8V of headroom to operate at 1000 Lux illumination. Internal temperature compensation allows dark current to be kept below 200nA over the full specification temperature range (-40 to +85°C), providing high accuracy at low light levels. Usable ambient light conditions range is from 1 to more than 5000 Lux. The LX1974 is optimized for controlling back lighting systems in low cost consumer products such as LCD TV, portable computers, and digital cameras. WWW . Microsemi . C OM Portable Electronic Displays LCD TV Backlight Systems Digital Still Cameras (DSC) Desktop Monitors Notebook Computers IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com Protected By U.S.Patents: 6,787,757; Patents Pending PRODUCT HIGHLIGHT LX1974 LIGHT LX1974 LX1974 PACKAGE ORDER INFO TA (°C) -40 to 85 BC Plastic 1206 2-Pin LX1974IBC RoHS Compliant / Pb-free Note: Available in Tape & Reel. Append the letters “TR” to the part number. (i.e. LX1974IBC-TR) Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET ABSOLUTE MAXIMUM RATINGS PACKAGE PIN OUT WWW . Microsemi . C OM Supply Input Voltage ...........................................................................-0.3V to 6V Ground Current ..........................................................................Internally Limited Operating Temperature Range .........................................................-40°C to 85°C Maximum Operating Junction Temperature ................................................ 150°C Storage Temperature Range.........................................................-40°C to +100°C RoHS / Pb-free Peak Package Solder Reflow Temperature (40 second maximum exposure) ..................................................... 260°C (+0, -5) Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. VDD 1 2 VSS BC PACKAGE (Top View) RoHS / Pb-free Gold Lead Finish THERMAL DATA BC Plastic 1206 2-Pin THERMAL RESISTANCE-JUNCTION TO AMBIENT, θJA 850°C/W Junction Temperature Calculation: TJ = TA + (PD x θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. FUNCTIONAL PIN DESCRIPTION Name VDD VSS Positive Terminal Negative Terminal CHARACTERISTIC CURVES Description PACKAGE DATA PACKAGE DATA Chart 1 & 2 – Step Response Graphs VDD = 4V, 200 to 20 Lux step 30.3K Load resistance Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET CHARACTERISTIC CURVES 2.5 WWW . Microsemi . C OM Operating Voltage 2.0 1.5 1.0 0.5 0 .0 -40 -20 0 20 40 60 80 10µA 100µA 200µA Temperature (°C) Chart 4 – Typical Operating Voltage Vs VSS Current 300 Dark Current (nA) 250 200 150 100 50 0 -40 -20 0 20 40 60 80 100 Chart 3 – Response vs. wavelenght Temperature (°C) Chart 5 – Dark Leakages Vs. Temperature 150 140 130 120 110 IOUT @ 1000 LUX, VDD=5.0V, 10K LOAD UA 100 90 80 70 CHARTS CHARTS 60 -60 -40 -20 0 20 40 60 80 100 Temperature Chart 6 – Typical Temperature Response Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET Unless otherwise specified, the following specifications apply over the operating ambient temperature -40°C ≤ TA otherwise noted and the following test conditions: See Note 1, VDD =5V, RSS = 10K Parameter RESPONSE ELECTRICAL CHARACTERISTICS ≤ 85°C except where WWW . Microsemi . C OM Symbol λPR Test Conditions Min LX1974 Typ 520 Max Units nm Peak Spectral Response Infrared Response IDD (λ ) IDD (λ PR ) VDD-VSS Minimum Operational Voltage Light Current Gain Linearity Dark Current Power Supply Rejection Ratio Radiant Sensitive Area ISS IDD(DARK) PSRR EV = 14.6μW/cm2, ISS = 10μA EV = 146μW/cm2, ISS = 100μA EV = 292μW/cm2, ISS = 200μA EV = 14.6μW/cm2 (100 lux), Note 2 EV = 146μW/cm2 (1K lux), Note 2 2 EV = 292μW/cm (2K lux), Note 2 2 14.6μW/cm ≤ EV ≤ 146μW/cm2 @ 25°C EV = 0μW/cm2, TA = 25°C EV = 0μW/cm2 VRIPPLE = 10mVP-P, f = 10kHz change with additional direct light input of 292μW/cm2 at 910nm, Note 3 2 EV(550nm) = 292μW/cm , Current responsivity -5 1 1.2 1.8 2.2 10 100 200 0.010 -25 0.04 5 1.4 2.1 2.6 12.5 125 250 15 50 200 % V 7.5 75 150 -15 μA % nA dB mm2 Notes: 1. The input irradiance (EV) is supplied from a white light-emitting diode (LED) optical source adjusted to impose the specified EV at a peak λ = 550nm. 2. See Figure 1. 3. See Figure 2. TEST CIRCUITS VDD VDD LX1974 White LED VSS 10k Ω Figure 1 – Operational Voltage Measurement Circuit LX1974 White LED 910nm 10kΩ VSS ELECTRICALS ELECTRICALS Figure 2 – IR Sensitivity Measurement Circuit Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET SIMPLIFIED BLOCK DIAGRAM WWW . Microsemi . C OM VDD Current Amp VSS Figure 3 – Simplified Block Diagram APPLICATION NOTE LIGHT UNITS In converting from µW/cm to lux it is necessary to define the light source. Lux is a unit for the measurement of illuminance, which is the photometric flux density or visible light flux density. Whereas µW/cm2 is a measurement of irradiance or the measurement of electromagnetic radiation, flux both visible and invisible. The first step in the conversion process is to convert irradiance to illuminance, which essentially involves running the irradiant flux through a photopic filter. In normal ambient, a photopic curve is used and in dark ambient, a scotopic curve (dark adapted eye) is used. If the light is composed of only one wavelength, a conversion chart will tell the conversion factor to convert µW/m2 to lux (lumens/m2). If more than one wavelength is used, the light spectrum of the irradiance must be applied to the photopic filter to determine the resultant illuminance. The most sensitive wavelength for the normal light adapted human eye is 555nm, which corresponds to yellowish-green light. At 555nm, the conversion factor is 683 Lux = 1W/m2 = 100µW/cm2. Therefore 14.6µW/cm2 = 100 lux at 555nm. 2 If the photo sensor had a truly photopic response, it would produce the same output current for the same number of lux, regardless of the color of the light. However, because the match is not perfect, there is still wavelength dependency particularly at the ends of the visible spectrum. In the case of the LX1974 the peak photo response is at 520nm, however depending on the light source, what the human eye perceives as ‘white’ light may actually be composed of peak wavelengths of light other than 520nm. For instance, a typical fluorescent lamp includes dominant light not only near 550nm but also at 404 and 435nm. Incandescent light sources such as standard tungsten lights generate substantial IR radiation out beyond 2000nm. For ease of automatic testing of the LX1974 the ATE (automatic test equipment) light source is configured with white LED’s whose current is adjusted to output a calibrated flux density at 550nm. This allows consistent and repeatable testing of the sensor but corresponds to a light source unlike that typically found in an office, home or sunlit environment. In practice, the user needs to place the sensor in the target environment and calibrate the sensors output current range to match the application objective. This is easily accomplished by adjusting the output resistor, which sets the sensor’s gain. APPLICATIONS APPLICATIONS Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET APPLICATION EXAMPLES The following examples present both fully automatic (no user input) and semi-automatic to fully manual override implementations. These general guidelines are applicable to a wide variety of potential light control applications. The LX1974 can be used to control the brightness input of CCFL inverters (like Microsemi’s PanelMatch™ inverter family, or line of controller IC’s). Likewise, it can interface well with LED drivers like the LX1990 and LX1991 sink LED drivers, or boost drivers like the LX1992, LX1993, LX1994, and LX1995. In each specific application, it is important to recognize the need to correlate the output current of the LX1974 for the target environment and its ambient light conditions. The mechanical mounting of the sensor, light aperture hole size, use of a light pipe or bezel are critical in determining the response of the LX1974 for a given exposure of light. 3.3V or 5V VDD VSS 3V R1 R2 The output node will actually reach 1.25V when the source current from the LX1974 is only about 44µA since about 6µA of current will be contributed from R1. This assumes a high impedance input to the LED driver. In Figure 5, user adjustable bias control has been added to allow control over the minimum and maximum output voltage. This allows the user to adjust the output brightness to personal preference over a limited range. In addition, an equivalent DC voltage may replace the PWM input source. 3.3V or 5V VDD VSS 3.3V PWM WWW . Microsemi . C OM R1 40K R2 25K To inverter brightness input or LED driver 10µF controller input. Figure 5 – Semi-Manual Controlled Dimming To inverter brightness input or LED driver controller. C1 10µF Figure 6 shows how a fully manual override can be quickly added to the example in figure 5. In addition to the gate to turn on and off the LX1974, a diode has been inserted to isolate the sensor when it is disabled. Disable control CMOS Gate VDD VSS Figure 4 – Fully Automatic Dimming The example in figure 4 shows a fully automatic dimming solution with no user interaction. Choose R1 and R2 values for any desired minimum brightness and slope. Choose C1 to adjust response time to filter 50/60 Hz room lighting. As an example, let’s say you wish to generate an output voltage from 0.25V to 1.25V to drive the input of an LED driver controller. The 0.25V represents the minimum LED brightness and 1.25V represents the maximum. The first step would be to determine the ratio of R1 and R2. ⎤ ⎡ 3.0V − 1 = 11 × R2 0.25V ⎥ ⎦ ⎣ Next the value of R2 can be calculated based on the maximum output source current coming from the LX1974 under the application’s maximum light exposure, lets say this has been determined to be about 50µA . Thus R2 can be calculated; first order as follows: ⎡1.25V ⎤ R2 = ⎢ = 25KΩ ∴ R1 = 11 × R2 = 275KΩ ⎣ 50µA ⎥ ⎦ R1 = R2 ⎢ 3.3V 60K PWM 30K 10µF 30K To inverter brightness input or LED driver controller. Figure 6 – Fully Manual Controlled Dimming APPLICATIONS APPLICATIONS The preceding examples represent just a few of the potential sensor applications. Further details and additional circuits can be found in the application note (AN-28) LX1970 Visible Light Sensor located in the application section of Microsemi’s website: www.microsemi.com. Although this application note is written around the LX1970 visible light sensor the circuits can be easily adapted for use with the LX1974. Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET APPLICATION CIRCUITS WWW . Microsemi . C OM L1 10µH D1 UPS5817 VIN R1 100K LX1995 IN C1 4.7µF BACKLIGHT GND SW FB C2 1µF SHDN GND SHDN R4 10K MMBT2907 R8 60.4K C3 10µF R10 49.9K R5 5.76K R6 15 R7 24.9K 3.3V LX1974 VSS VDD C4 0.1µF Figure 7 – Typical Application with Microsemi’s LX1995 LED Driver IC 22µH VIN = 2.0V to 5.5V FDN337 PWM Dimming Input UPS5819 1M 1µF VIN 4.99K DRV SRC OVP FB CMP 0.1µF 41.2K 15 S/P BRT LS GND 3.3V LX1974 VDD VSS MMBT2907 15K 22µF 100K 178K 1µF LX1994 APPLICATIONS APPLICATIONS Figure 8 – Typical Application with Microsemi’s LX1994 LED driver IC Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET PACKAGE DIMENSIONS WWW . Microsemi . C OM BC 2-Pin 1206 Standard Carrier D CL Sensor Active Area: 0.2 x 0.2mm 2 P C 0.03 CL C R 1 2 Top E θ 0.19 - 0.25mm Sensor Active Area A Side B 1 Bottom H X Pin 1 Indicator (top side) / Alignment Indicator (Bottom side) Dim A B C D E H Θ P R X MILLIMETERS MIN MAX 0.95 1.25 0.40 0.70 0.90 1.10 3.05 3.35 1.90 2.10 0.40 0.60 3° nom 1.45 1.75 0.25 nom 0.02 0.05 INCHES MIN MAX 0.037 0.049 0.016 0.028 0.035 0.043 0.120 0.132 0.075 0.083 0.016 0.024 3° nom 0.057 0.069 0.010 nom 0.001 0.002 Note: Dimensions do not include protrusions; these shall not excee 0.155mm (.006”) on any side. 1.50mm 0.06in. Recommended Soldering Pattern for reflow soldering of the BC (1206) package. 1.50mm 2.0mm 0.06in. 1.50mm 0.06in. 0.08in. Super Imposed 1206 Package Basic specification is < 5 seconds @ 260°C when applying solder. 4.00 1.75 Lead In: 10 min empty Loaded: 3000 pcs Lead Out: 40 min empty 5.25 8.00 2.00 MECHANICALS MECHANICALS 0.20 4.00 1.30 Note: LX1974 parts are loaded bottom side up Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 8 LX1974 TM ® Ambient Light Detector P RODUCTION D ATA S HEET NOTES WWW . Microsemi . C OM NOTES NOTES PRODUCTION DATA – Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright © 2005 Rev. 1.0, 2006-05-09 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 9