LX5204CPWP

LIN D O C # : 5204 LX5204 9-L I N E H O T S WA P , µP O W E R S CSI T E R M I N AT O R T HE I NFINITE P OWER OF I N N O VAT I O N P RODUCTION D ATA S HEET DESCRIPTION The LX5204 is a nine-line active terminator for the SCSI parallel bus. This SCSI standard recommends active termination at both ends of the SCSI bus. The LX5204 has the added features of hot swappability, fully complying with the SCSI hot swap specification. During disconnect mode, the LX5204 requires a meager 60µA of supply current while offering only 3.5pF of output capacitance. To enter this low-power mode, the disconnect pin can be left open (floating) or driven high, thereby disconnecting the terminating resistors and placing the internal low dropout regulator into low-power mode. In disconnect mode, each termination line presents a high impedance to the SCSI bus with the overall effect being to preserve high-signal integrity and yield subsequent reliable, errorfree communications. During normal operation, the LX5204 consumes only 600µA of current, which is the lowest enabled supply current of any terminator available on the market today. Linfinity's proprietary BiCMOS low dropout regulator architecture enables this unique and very efficient operating characteristic. The LX5204 also offers a precisely trimmed channel output current specified to a 5% tolerance. The maximum value of the output current is trimmed as closely as possible to the SCSI standard maximum specification to give the highest possible noise margin for fast SCSI operation. And the LX5204 sinks up to 150mA of current, making it compatible with today's fast active negation drivers. The LX5204 is a superior, pin-for-pin replacement for a variety of industry products such as the UC5603 and UC5613. K E Y F E AT U R E S s 3.5pF OUTPUT CAPACITANCE DURING DISCONNECT s HOT SWAP COMPATIBLE s 60µA SUPPLY CURRENT IN DISCONNECT MODE s 600µA SUPPLY CURRENT DURING NORMAL OPERATION s 150mA SINK CURRENT FOR ACTIVE NEGATION s LOGIC COMMAND DISCONNECTS ALL TERMINATION LINES s CURRENT LIMIT AND THERMAL PROTECTION s COMPATIBLE WITH SCSI 1, 2 AND 3 STANDARDS s CONSULT FACTORY FOR APPLICATION TEST REPORT: 5204TR IMPORTANT: For the most current data, consult LinFinity's web site: h ttp://www.linfinity.com. PRODUCT HIGHLIGHT R E C E I V I N G W AV E F O R M - 1 0MH Z D R I V I N G W AV E F O R M - 1 0MH Z Receiver 1 Meter, AWG 28 LX5204 LX5268 Driver LX5204 LX5268 PA C K A G E O R D E R I N F O R M AT I O N TA (°C) 0 to 70 NOTE: For An In-Depth Discussion On Applying SCSI, Request Linfinity Application Note: "Understanding The Single-Ended SCSI Bus" PWP Plastic TSSOP 24-pin, Power LX5204CPWP DP Plastic SOIC 16-pin, Power LX5204CDP Note: All surface-mount packages are available in Tape & Reel. Append the letter "T" to part number. (i.e. LX5204CDPT) Copyright © 1997 Rev. 1.1 12/96 LINFINITY MICROELECTRONICS INC. 11861 W ESTERN A VENUE, G ARDEN G ROVE, CA. 92841, 714-898-8121, F AX: 714-893-2570 1 P R O D U C T D ATA B O O K 1 9 9 6 / 1 9 9 7 LX5204 9 -L I N E H O T S WA P , µP O W E R S CSI T E R M I N AT O R P RODUCTION D ATA S HEET A B S O L U T E M A X I M U M R AT I N G S (Note 1) PACKAGE PIN OUTS TermPwr Voltage ......................................................................................................... +7V Signal Line Voltage ............................................................................................ 0V to +7V Regulator Output Current ........................................................................................... 0.4A Operating Junction Temperature Plastic (PWP, DP Packages) ................................................................................. 150°C Storage Temperature Range ...................................................................... -65°C to 150°C Lead Temperature (Soldering, 10 seconds) ............................................................. 300°C Note 1. Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. T7 T8 T9 N.C. GND  N.C.  N.C.  Heatsink   N.C.   N.C. DISCONNECT T1 T2 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 T6 T5 REG OUT N.C. N.C.  N.C.    Heatsink N.C.   N.C.  N.C. VTERM T4 T3 T H E R MAL DATA PWP PACKAGE: THERMAL RESISTANCE-JUNCTION TO LEADS, θJL THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA DP PACKAGE: THERMAL RESISTANCE-JUNCTION TO LEADS, θJL THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA 20°C/W 45°C/W 27°C/W 60°C/W T7 T8 T9 Heatsink { N.C. GND DISCONNECT T1 T2 PWP PACKAGE (Top View) 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 Junction Temperature Calculation: TJ = TA + (PD x θJA). The θ JA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. T6 T5 REG OUT N.C.  Heatsink  N.C.  VTERM T4 T3 DP PACKAGE (Top View) POWER UP / POWER DOWN FUNCTION T ABLE Disconnect L H Open Outputs Enabled HI Z HI Z Quiescent Current 600µA 60µA 60µA 2 Copyright © 1996 Rev. 1.1 12/96 P R O D U C T D ATA B O O K 1 9 9 6 / 1 9 9 7 LX5204 9 -L I N E H O T S WA P , µP O W E R S CSI T E R M I N AT O R P RODUCTION D ATA S HEET R E C O M M E N D E D O P E R AT I N G C O N D I T I O N S Parameter TermPwr Voltage Signal Line Voltage Disconnect Input Voltage Output Capacitor on REGOUT Operating Virtual Junction Temperature Range LX5204C Note 2. Range over which the device is functional. (Note 2) Symbol VTERM Recommended Operating Conditions Min. Typ. Max. 4 0 0 2.2 0 5.25 5 VTERM Units V V V µF °C 125 ELECTRICAL CHARACTERISTICS (Unless otherwise specified, these specifications apply over the operating ambient temperature range of 0°C ≤ T A ≤ 70°C. TermPwr = 4.75V, Disconnect = 0V. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) Parameter Supply Current Section TermPwr Supply Current Power Down Mode Symbol Test Conditions Min. LX5204 Typ. Max. 0.6 194 60 1.2 208 100 Units All term lines = Open All term lines = 0.5V Disconnect = Open ITERM = -5mA to -15mA, TA = 25°C ITERM = -5mA to -15mA VOUT = 0.5V, T A = 25°C VOUT = 0.5V, 0°C ≤ TA ≤ 70°C VOUT = 0.5V, V TERM = 4V, TA = 25°C VOUT = 0.5V, V TERM = 4V, 0°C ≤ TA ≤ 70°C Disconnect = Open, VTERM = 0V to 5.25V Disconnect = Open VOUT = 4V 104 100 2.7 -20.3 -19.0 -19.5 -18.0 mA mA µA Ω Ω V mA mA mA mA nA pF mA Output Section (Terminator Lines) Terminator Impedance Terminator Output High Voltage Max. Output Current 110 116 110 120 2.9 -21.8 -23 -21.8 -23 -21.8 -23 -21.8 -23 10 400 3.5 20 30 Fully Compliant 3.6 10 20 0.7 -200 150 0.8 Disconnect = 0V Output Leakage Output Capacitance Sink Current Hot Swap Regulator Section Regulator Output Voltage Line Regulation Load Regulation Drop Out Voltage Short Circuit Current Thermal Shutdown VTERM = 4V to 6V I REG = 0 to -50mA IREG = -50mA VREG = 0V 20 50 1.0 -350 V mV mV V mA °C V µA Disconnect Section Disconnect Threshold Input Current 2.0 40 Copyright © 1996 Rev. 1.1 12/96 3 P R O D U C T D ATA B O O K 1 9 9 6 / 1 9 9 7 LX5204 9 -L I N E H O T S WA P , µP O W E R S CSI T E R M I N AT O R P RODUCTION D ATA S HEET BLOCK DIAGRAM FIGURE 1 — LX5204 BLOCK DIAGRAM REG OUT VTERM DISCONNECT VBG T0 VTERM Channel 1 of 9 VTERM T8 A P P L I C AT I O N S C H E M AT I C FIGURE 2 — 8-BIT SCSI SYSTEM APPLICATION 5V 2.2µF TERM POWER VTERM HOST PERIPHERAL TERM POWER VTERM 2.2µF 5V DISCONNECT LX5204 REGOUT 2.2µF LX5204 DB (6) DB (7) DB (P) DB (6) DB (7) DB (P) ~~~ REGOUT 2.2µF TERMPWR VTERM TERMPWR DISCONNECT 2.2µF Copyright © 1996 Rev. 1.1 12/96 DISCONNECT ATN BSY ACK RST MSG VTERM SCSI CABLE ATN BSY LX5204 ACK RST MSG LX5204 REGOUT 2.2µF ~~~ ~~ REGOUT Note: Add third LX5204 for 16-bit SCSI PRODUCTION DATA - Information contained in this document is proprietary to Lin Finity, and is current as of publication date. This document may not be modified in any way without the express written consent of LinFinity. Product processing does not necessarily include testing of all parameters. Linfinity reserves the right to change the configuration and performance of the product and to discontinue product at any time. 4 DISCONNECT DB (0) DB (1) ~~ DB (0) DB (1)