LX5211CDP

LIN D O C # : 5211 LX5211 9-LINE LOW CAPACITANCE, µP OWER SCSI TERMINATOR T HE I NFINITE P OWER OF I N N O VAT I O N P RODUCTION D ATA S HEET DESCRIPTION The LX5211 is a nine-line active terminator for the SCSI parallel bus. The SCSI standard recommends active termination at both ends of the SCSI bus. During disconnect mode, the LX5211 requires a meager 500nA of supply current while offering only 2.5pF of output capacitance. To enter this low-power mode, the disconnect pin can be left open (floating) or driven low, thereby disconnecting the terminating resistors and placing the internal low dropout regulator into low-power mode. In disconnect mode, each termination line presents a high impedance to the SCSI bus with the overall effect being to preserve high signal integrity and yield subsequent reliable, error-free communications. During normal operation, the LX5211 consumes only 600µA of current, which is the lowest enabled supply current of any terminator available on the market today. Linfinity's proprietary BiCMOS low dropout regulator architecture enables this unique and very efficient operating characteristic. The LX5211 also offers a precisely trimmed channel output current specified to a 5% tolerance. The maximum value of the output current is trimmed as closely as possible to the SCSI standard maximum specification to give the highest possible noise margin for fast SCSI operation. And the LX5211 sinks up to 30mA of current, making it compatible with today's fast active negation drivers. The LX5211 is a stable, pin-for-pin replacement for a variety of industry products, such as the UCC5606. K E Y F E AT U R E S s 2.5pF OUTPUT CAPACITANCE DURING DISCONNECT s 500nA SUPPLY CURRENT IN DISCONNECT MODE s 600µA SUPPLY CURRENT DURING NORMAL OPERATION s 30mA SINK CURRENT FOR ACTIVE NEGATION s LOGIC COMMAND DISCONNECTS ALL TERMINATION LINES s CURRENT LIMIT AND THERMAL PROTECTION s COMPATIBLE WITH SCSI 1, 2, 3, AND ULTRA SCSI STANDARDS s HOT SWAP COMPATIBLE s CONSULT FACTORY FOR APPLICATION TEST REPORT: 5211TR s EVALUATION BOARD AVAILABLE: REQUEST LXE9005 EVALUATION KIT IMPORTANT: For the most current data, consult LinFinity's web site: http://www.linfinity.com. PRODUCT HIGHLIGHT R E C E I V I N G W AV E F O R M - 20MHZ D R I V I N G W AV E F O R M - 20MHZ Receiver 1 Meter, AWG 28 LX5211 LX5268 Driver LX5211 LX5268 PA C K A G E O R D E R I N F O R M AT I O N TA (°C) 0 to 70 NOTE: For An In-Depth Discussion On Applying SCSI, Request Linfinity Application Note: "Understanding The Single-Ended SCSI Bus" PWP Plastic TSSOP 24-pin, Power LX5211CPWP DP Plastic SOIC 16-pin, Power LX5211CDP Note: All surface-mount packages are available in Tape & Reel. Append the letter "T" to part number. (i.e. LX5211CDPT) Copyright © 1997 Rev. 1.1 5/97 LINFINITY MICROELECTRONICS INC. 11861 W ESTERN A VENUE, G ARDEN G ROVE, CA. 92841, 714-898-8121, F AX: 714-893-2570 1 PRODUCT DATABOOK 1996/1997 LX5211 9-LINE LOW CAPACITANCE, µP OWER SCSI TERMINATOR P RODUCTION D ATA S HEET A B S O L U T E M A X I M U M R AT I N G S (Note 1) PACKAGE PIN OUTS T7 T8 T9 N.C. GND HEATSINK/GND HEATSINK/GND HEATSINK/GND HEATSINK/GND DISCONNECT T1 T2 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 TermPwr Voltage ................................................................................................. +7V Signal Line Voltage ................................................................................... 0V to +7V Regulator Output Current ................................................................................... 0.4A Operating Junction Temperature Plastic (PWP, DP Packages) ........................................................................ 150°C Storage Temperature Range .............................................................. -65°C to 150°C Lead Temperature (Soldering, 10 seconds) .................................................... 300°C Note 1. Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. T6 T5 REG OUT N.C. HEATSINK/GND HEATSINK/GND HEATSINK/GND HEATSINK/GND N.C. VTERM T4 T3 T H E R MAL DATA PWP PACKAGE: THERMAL RESISTANCE-JUNCTION TO LEADS, θJL THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA DP PACKAGE: THERMAL RESISTANCE-JUNCTION TO LEADS, θJL THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA 20°C/W 50°C/W 27°C/W 100°C/W T7 T8 T9 HEATSINK/GND GND DISCONNECT T1 T2 PWP PACKAGE (Top View) 16 2 3 4 5 6 7 8 15 14 13 12 11 10 9 Junction Temperature Calculation: TJ = TA + (PD x θJA). The θ JA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. T6 T5 REG OUT HEATSINK/GND HEATSINK/GND VTERM T4 T3 DP PACKAGE (Top View) POWER UP / POWER DOWN FUNCTION TABLE DISCONNECT L H Open Outputs HI Z Enabled HI Z Quiescent Current 0.5µA 600µA 0.5µA 2 Copyright © 1997 Rev. 1.1 5/97 PRODUCT DATABOOK 1996/1997 LX5211 9-LINE LOW CAPACITANCE, µP OWER SCSI TERMINATOR P RODUCTION D ATA S HEET R E C O M M E N D E D O P E R AT I N G C O N D I T I O N S Parameter TermPwr Voltage Signal Line Voltage DISCONNECT Input Voltage Output Capacitor on REGOUT Operating Virtual Junction Temperature Range LX5211C Note 2. Range over which the device is functional. (Note 2) Symbol VTERM Recommended Operating Conditions Min. Typ. Max. 4 0 0 2.2 0 5.25 5 VTERM Units V V V µF °C 125 ELECTRICAL CHARACTERISTICS (Unless otherwise specified, these specifications apply over the operating ambient temperature range of 0°C ≤ TA ≤ 70°C. TermPwr = 4.75V, DISCONNECT = 0V. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) Parameter Supply Current Section TermPwr Supply Current Power Down Mode Symbol Test Conditions Min. LX5211 Typ. Max. 0.6 194 0.5 1.2 210 1 116 120 -23 -23 -23 -23 400 Units All term lines = Open All term lines = 0.5V DISCONNECT = Open ITERM = -5mA to -15mA, TA = 25°C ITERM = -5mA to -15mA VOUT = 0.5V, T A = 25°C VOUT = 0.5V, 0°C ≤ TA ≤ 70°C VOUT = 0.5V, V TERM = 4V, TA = 25°C VOUT = 0.5V, V TERM = 4V, 0°C ≤ TA ≤ 70°C DISCONNECT = Open, VTERM = 0V to 5.25V DISCONNECT = Open VOUT = 4V 104 100 2.7 -20.3 -19.0 -19.5 -18.0 mA mA µA Ω Ω V mA mA mA mA nA pF mA V mV mV V mA °C V µA Output Section (Terminator Lines) Terminator Impedance Terminator Output High Voltage Max. Output Current 110 110 2.9 -21.8 -21.8 -21.8 -21.8 10 2.5 30 3.6 10 20 0.7 -200 150 0.8 DISCONNECT = 0V Output Leakage Output Capacitance Sink Current 20 Regulator Section Regulator Output Voltage Line Regulation Load Regulation Drop Out Voltage Short Circuit Current Thermal Shutdown VTERM = 4V to 6V I REG = 0 to -50mA IREG = -50mA VREG = 0V 20 50 1.0 -350 Disconnect Section DISCONNECT Threshold Input Current 2.0 40 Copyright © 1997 Rev. 1.1 5/97 3 PRODUCT DATABOOK 1996/1997 LX5211 9-LINE LOW CAPACITANCE, µP OWER SCSI TERMINATOR P RODUCTION D ATA S HEET BLOCK DIAGRAM FIGURE 1 — LX5211 BLOCK DIAGRAM REG OUT VTERM DISCONNECT VBG T0 VTERM Channel 1 of 9 VTERM T8 A P P L I C AT I O N S C H E M AT I C FIGURE 2 — 8-BIT SCSI SYSTEM APPLICATION 5V 2.2µF TERM POWER VTERM HOST PERIPHERAL TERM POWER VTERM 2.2µF 5V DISCONNECT LX5211 REGOUT 2.2µF LX5211 DB (6) DB (7) DB (P) DB (6) DB (7) DB (P) ~~~ REGOUT 2.2µF TERMPWR VTERM TERMPWR DISCONNECT SCSI CABLE LX5211 REGOUT 2.2µF LX5211 ACK RST MSG ACK RST MSG ~~~ REGOUT 2.2µF Note: Add third LX5211 for 16-bit SCSI PRODUCTION DATA - Information contained in this document is proprietary to Lin Finity, and is current as of publication date. This document may not be modified in any way without the express written consent of LinFinity. Product processing does not necessarily include testing of all parameters. Linfinity reserves the right to change the configuration and performance of the product and to discontinue product at any time. 4 Copyright © 1997 Rev. 1.1 5/97 DISCONNECT ATN BSY VTERM ATN BSY ~~ DISCONNECT DB (0) DB (1) ~~ DB (0) DB (1)