LX8941CP

LIN D O C # : 8941 LX8941 A D J U S TA B L E LO W D R O P O U T R E G U L AT O R T HE I NFINITE P OWER OF I N N O VAT I O N P RELIMINARY D ATA S HEET DESCRIPTION The LX8941 is an adjustable, low dropout regulator rated for more than 1A of output current. It can regulate with as low as 0.8V headroom between the input and output voltages, at 1A output current, thus minimizing power dissipation. In addition, it can be used in applications where worst case supplies require a low input-output differential to maintain regulation. This feature makes it ideal for some processor applications that require 4V operation from a 5V supply. In addition, the LX8941 provides an on/off switch that reduces the IC quiescent current when activated, making it ideal for battery operated applications. K E Y F E AT U R E S s 2% Internally Trimmed Output s Output Current In Excess Of 1A s Input-Output Differential Less Than 0.8V At 1A p Reverse Battery Protection p Short Circuit Protection p Internal Thermal Overload Protection p Available In 5-Lead Plastic TO-220 And Surface-Mount TO-263 NOTE: For current data & package dimensions, visit our web site: http://www.linfinity.com. PRODUCT HIGHLIGHT D R O P O U T V O LTA G E V S . O U T P U T C U R R E N T V S . T E M P E R AT U R E 5V 10µF ON ADJ 22µF IN LX8941 OUT 600 4V 500 125°C Dropout Voltage - (mV) 400 25°C 300 OFF 200 -40°C 100 0 100 500 1000 Output Current - (mA) PA C K A G E O R D E R I N F O R M A T I O N T A (°C) 0 to 70 P Plastic TO-220 5-pin LX8941CP DD Plastic TO-263 5-pin LX8941CDD Note: All surface-mount packages are available in Tape & Reel. Append the letter "T" to part number. (i.e. LX8941CDDT) Copyright © 1999 Rev. 0.6 4/99 LINFINITY MICROELECTRONICS INC. 11861 W ESTERN A VENUE, G ARDEN G ROVE, CA. 92841, 714-898-8121, F AX: 714-893-2570 1 PRODUCT DATABOOK 1996/1997 LX8941 A D J U S TA B L E LO W D R O P O U T R E G U L AT O R P RELIMINARY D ATA S HEET A B S O LUT E M AXIM UM R ATINGS (Note 1) PACKAGE PIN OUTS Input Voltage (VIN) ....................................................................................................... 26V Operating Junction Temperature Plastic (P, DD Package) ........................................................................................ 150°C Storage Temperature Range ...................................................................... -65°C to 150°C Lead Temperature (Soldering, 10 seconds) ............................................................. 300°C Note 1. Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. TAB IS GND 5 1 ON/OFF ADJ GND VO VIN P PACKAGE (Top View) THERMAL DATA P PACKAGE: THERMAL RESISTANCE-JUNCTION TO TAB, θJT THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA DD PACKAGE: THERMAL RESISTANCE-JUNCTION TO TAB, θJT THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA 4.5°C/W 60°C/W 4.5°C/W 60°C/W 5 4 3 2 1 TAB IS GND ON/OFF ADJ GND VO VIN Junction Temperature Calculation: TJ = TA + (P D x θ JA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. DD PACKAGE (Top View) BLOCK DIAGRAM INPUT VOLTAGE C1* 0.1µF VIN * Required if regulator is located far from power supply filter. 1 2 VO OUTPUT VOLTAGE C2 10µF THERMAL SHUTDOWN ON ON/ OFF 4 ADJ 5 ON/OFF CIRCUIT OFF 3 GND LX8941 2 Copyright © 1999 Rev. 0.6 4/99 PRODUCT DATABOOK 1996/1997 LX8941 A D J U S TA B L E LO W D R O P O U T R E G U L AT O R P RELIMINARY D ATA S HEET R E C O M M E N D E D O P E R AT I N G C O N D I T I O N S Parameter Input Voltage (Note 2) Load Current (with adequate heatsinking) Input Capacitor (VIN to GND) Output Capacitor with ESR of 10Ω max., (VOUT to GND) Note 2. VIN (MIN) = VOUT + 1.2∆V (MAX). See Dropout Voltage maximum limit. Symbol VIN Recommended Operating Conditions Min. Typ. Max. 3.8 5 0.1 10 26 1000 Units V mA µF µF ELECTRICAL CHARACTERISTICS Unless otherwise specified, these specifications apply over the operating ambient temperature of 0°C to +125°C for LX8941CP; VIN = 10V, IO = 1A, C OUT = 22µF, and are for DC characteristics only. (Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) Parameter ADJ Pin Voltage Line Regulation Load Regulation Dropout Voltage Symbol VO ∆VOI ∆VOL ∆V Test Conditions IO = 0A, TA = 25ºC VO + 2V ≤ V IN ≤ 26V, IO = 5mA 50mA ≤ IO ≤ 1A, VO = VADJ IO = 100mA IO = 500mA I O = 1A IO ≤ 5mA, 7 ≤ VIN ≤ 26V IO = 500mA IO = 1000mA VIN = 10V, IO = 1A VIN = 26V 10Hz - 100kHz, IO = 5mA fO = 120Hz, 1VRMS, IO = 100mA Min. 1.225 LX8941 Typ. 1.25 1 10 150 275 400 3 30 115 2 1.2 150 20 66 Max. 1.275 50 50 300 500 800 15 50 180 20 Units V mV mV mV mV mV mA mA mA µA A µVRMS mV/1000hr dB V µA V µA Quiescent Current IQ Adjust Pin Current Current Limit Output Noise Voltage (Note 3) Long Term Stability (Note 3) Ripple Rejection (Note 3) I ADJ I CL VO RMS RR 1 Enable Logic Section On Threshold Voltage On Threshold Current Off Threshold Voltage Off Threshold Current Note 3. These parameters, although guaranteed, are not tested in production. 2 50 0.8 -10 PRELIMINARY DATA - Information contained in this document is pre-production data, and is proprietary to LinFinity. It may not modified in any way without the express written consent of LinFinity. Product referred to herein is offered in sample form only, and Linfinity reserves the right to change or discontinue this proposed product at any time. Copyright © 1999 Rev. 0.6 4/99 3