PD67108MAC-GGGG

PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) DESCRIPTION KEY FEATURES Microsemi’s™ new and unique family of Power over Ethernet (PoE) modules enable next-generation network devices to share data and power over the same cable. The PD671xxx PoE PSE modules are fit / form compatible with the standard plug-in memory modules used in personal computers (Dual Inline Memory Modules - DIMMs) (see Figure 1 and Figure 12). Thus, the use of these modules permit network devices to be designed for up to 96 ports, with fewer ports actually installed. Additional modules can be inserted in the field at any time. The PD671xxx (8, 12 or 24 ports DIMM) includes a wide range of functions. Some of these modules include the PD69000 micro-controller unit (PoE controller) for Enhanced features and a flexible work environment in a DIMM master or DIMM slave configuration (refer to Ordering Information, page 2). Microsemi’s PoE PD671xxx DIMMs implement real time mechanisms including detection, classification, port real-time protection and system level functions (power management and MIB support). Microsemi’s PD69012 IC, 12-channel PoE Manager IC is at the heart of these modules. PD671xxx DIMMs enable the detection of IEEE802.3at-2009 Type 1 (low power) or Type 2 (high power) Powered Devices (PDs), ensuring safe power feeding and removal over Ethernet ports. The PD69012-based DIMMs detect and disable disconnected ports, using DC or AC disconnection methods. The DIMMs are embedded in multiport and highly populated Ethernet switches, requiring a minimum of external components. The PD671xxx DIMM is fully backwards compatible with the PD670xx DIMM and can be dropped into existing designs. Figure 1: PoE PD67124 DIMM IMPORTANT: For the most current data, consult Microsemi’s website: http://www.microsemi.com IEEE 802.3AT-2009 and IEEE802.3AF-2003 compliant Up to 30 W per port power PoE solution RoHS compliant Supports IETF PoE MIB (RFC 3621) Up to 24 power ports per single DIMM Up to 96 ports in a system, using master and slave configuration Thermal protection per port Thermal monitoring capabilities Pre-standard detection methods (Cisco Inline Power and Power over LAN Legacy) Non-standard terminals supported DC disconnect with DC modulation AC disconnect function utilizing external diodes PD 2-events classification function Operates using a single input (44 to 57 VDC) I2C or UART host interface Host communication is backward compatible with PD67024M communication, or Marvell® ISSR Programmable over current protection per port Built-in power management algorithm Internal power-on reset mechanism Fast port shutdown on power supply failure Supports Backplane Power Management Automatic on/off sequencer for 96 ports Disable/enable power per port Continuous port current monitoring Serial interface for LED indicator support Backwards compatible with PD670xx Fit/form compliant with168-pin DIMM JEDEC MO-161F, 3.3 V Space efficient compact design Factory pre-tested, for plug-and-play integration Safety standard compliant: UL / cUL per UL60950-1 (mounted on Microsemi evaluation board) PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Ordering Information Part Number PD67124MDC-gggg [1] PD67124S PD67112MDC-gggg PD67108MDC-gggg PD67124MAC-gggg PD67112MAC-gggg PD67108MAC-gggg PD67124AM PD67124AS PD67112AM PD67108AM Ports 24 24 12 8 24 12 8 24 24 12 8 Port Disconnect Method DC AC/DC DC DC AC AC AC AC/DC AC/DC AC/DC AC/DC [5] [5] [5] [5] [4] DIMM Master/Slave Master Slave [2] Mode Enhanced/Auto [3] Enhanced Enhanced Enhanced Enhanced Enhanced Enhanced Enhanced Auto Auto Auto Auto W WW . Microsemi . C OM Master Master Master Master Master Master Slave [2] Master Master Note: [1] – gggg: MCU software version. [2] – DIMM Slave should be used in conjunction with DIMM Master (for systems require more than 24 ports). [3] – Enhanced and Auto mode of operation stand for the PoE system features. The Enhanced mode system includes the PD69000 PoE controller. [4] – DIMM Slave port disconnection method is determined by the DIMM Master which controllers it. [5] – DIMM functioning at the Auto Mode Configuration can be configured to AC or DC port disconnection method by the system host. Further details can be found in the Auto Mode User Guide, Catalogue Number 06-1200-056. APPLICABLE DOCUMENTS IEEE 802.3at-2009 standard, DTE Power via MDI PD69012 Data Sheet, Catalogue Number 06-0069-058 PD69000 Data Sheet, Catalogue Number 06-0070-058 Serial Communication Protocol User Guide 06-0032-056 Auto Mode User Guide, Catalogue Number 06-1200-056 Layout Design Guidelines for DIMM-based PoE Systems, AN-132 Catalogue Number 06-0010-080 Designing a DIMM-based PoE System, AN-133 Catalogue Number 06-0011-080 ♦ PD671xx DIMM Copyright © 2009 Microsemi Page 2 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) ABSOLUTE MAXIMUM RATINGS Vmain DGND, AGND, QGND VPORT_POSx, VPORT_NEGx 3_3Vout EXT_REG I2C_Addr_M. MISO, MOSI, SCK, CS, SCL, SDA, SSn, Led_Cs, Asic_Reset ESD (Human Body Model) Storage temperature Notes: “x” defines port numbers, 0 to 11, inclusive. -0.3 to 80 VDC (1) -0.3 to 0.3 VDC (2) -0.3 to 80 VDC (1) 3.8 VDC -0.3 to 6 VDC -0.3 to (3_3Vout + 0.3 VDC) -0.3 to (3_3Vout + 0.3 VDC) ± 2 kV (3) -40° to +125° C W WW . Microsemi . C OM (1) 80 VDC is the transient voltage that can be applied for up to one minute. (2) Maximum voltage value between grounds. (3) ESD Human Body Model is: (CZap = 100 pF, RZap = 1500 Ω). Stresses beyond those listed above can cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods could affect device reliability. CALCULATED MTBF DATA [1] Operation mode Failures per 10^6 Hours MTBF(Hours) PD67124M @ 25°C Ambient IEEE 802.3AT-2009 0.5181 1930000 PD67124M @ 25°C Ambient IEEE802.3AF-2003 0.5128 1950000 Notes: [1] – MTBF calculation made for the worst case PoE DIMM populated with 24 fully loaded ports PD671xx DIMM Copyright © 2009 Microsemi Page 3 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) OPERATING CONDITIONS PARAMETER Operating ambient temperature Operating voltage (see Figure 2) Operating humidity (non-condensing, Per IEC 68-2-56) Notes: Operating functions depend on the input voltage. Operating voltage range for IEEE802.3AF is 44 to 57 VDC Operating voltage range for IEEE802.3AT (High Power) is 50 to 57 VDC MIN. -10 40 to 44 NOM. 44 to 55 MAX. +70 55 to 57 95 UNIT °C VDC % W WW . Microsemi . C OM Figure 2: Operational voltage Ranges Airflow To prevent overheating, the application designer should supply a minimal airflow to the PD671xxx DIMMs. Figure 3 shows the power handling capability versus air velocities in meter/second, as measured at all points of the DIMM envelope, prior to insertion into the connector(s). As shown in Figure 12, the connectors are spaced by 35 mm; 1 m/s = 197 LFM (linear feet per minute). Maximum allowed temperature is +85° C for the MCU (PD69000) and +125° C for the PD69012. Power per Port 35 30 25 20 15 10 5 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 Ambient temperature 0.5m/S 1m/S PD671xx DIMM Air flow 0m/S Figure 3: Power per Port for two DIMMs (48 ports) Copyright © 2009 Microsemi Page 4 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Electrical Characteristics _________________________________ The following sections detail the DC and analog characteristics. DC Characteristics for Digital Inputs and Outputs PARAMETER Pin Name Type High level input voltage Low level input voltage Input voltage hysteresis Input high current Input low current Pin Name Type High level input voltage Low level input voltage Input voltage hysteresis Input high current Input low current High level output voltage Low level output voltage Tri state output current Pin Name Type High level input voltage Low level output voltage Low level input voltage Input voltage hysteresis OFF state output current SYMBOL MIN. MAX. UNIT REMARKS SCL, xDisable_Ports, Rx (without internal pull-up/pull-down resistor) Schmitt Trigger CMOS input, TTL level VIH 2.0 V VIL 0.8 V 0.3 V IIH -1 +1 μA IIL -1 +1 μA MOSI, MISO, CS, Tx (without internal pull-up/down resistor) SCK (with internal resistor) CMOS I/O, TTL level VIH 2.0 V VIL 0.8 V 0.3 V IIH -1 +1 μA IIL -1 +1 μA VPERI-0.4V V Iout = 3 mA 0.4 V Iout = 3 mA -1 +1 μA xAsic_Reset (with internal resistor) SDA (without internal resistor) CMOS open drain output with Schmitt Trigger input, TTL level VIH 2.0 V VOH 0.4 V Iout = 3mA VIL 0.8 V 0.3 V -1 +1 μA W WW . Microsemi . C OM Electrical Characteristics for Analog I/O Pads PARAMETER Pin Name Operating voltage Pin current consumption MIN MAX UNIT V μA Port driver, Vport measurement and AC generator are off Port driver, Vport measurement and AC generator are off Recommended Range 48v to 55v Recommended Range 51v to 55v Total on Vmain Without external NPN (see Q1 in Figure 8) When using external NPN for VPERI (see Q1 in Figure 8) REMARKS VPORT_POSx 44 62 -5 +10 Pin Name VPORT_NEGx Operating voltage 0 Vmain V Pin current consumption -5 +10 μA Pin Name Vmain Operating voltage – AF mode 40 57 V Operating voltage – AT mode 50 57 V Vmain current consumption 40 mA Pin Name 3_3Vout Voltage 3.13 3.46 V Output current 6 mA 30 mA PD671xx DIMM Copyright © 2009 Microsemi Page 5 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Dynamic Characteristics____________ The PD671xxx DIMMs utilize three programmable current level thresholds (Imin, Icut, Ilim) and two timers (Tmin, Tcut), to operate as shown in Figure 4. Loads that consume more than Icut for longer than Tcut (OVL_S to OVL) are categorized as ‘overloads’ and are automatically shutdown. Automatic recovery from overload and no-load conditions is attempted every TOVLREC and TUDLREC periods (typically 5 and 1 seconds, respectively). Output current is limited to Ilim, which is the maximum peak current allowed at each port. PARAMETER Automatic recovery from Automatic recovery from noInrush current Output current operating range Output power available, operating range DC disconnect OFF mode AC Disconnect OFF mode PD power maintenance Over load current detection range Over load time limit Turn on rise time Port turn off time CONDITIONS TOVLREC value, measured from port shutdown (can be modified via control port) TUDLREC value, measured from port shutdown point (can be modified via control port) IInrsh For t = 50 ms, Cload =180 uF max. Iport Continuous operation after startup period Continuous operation after startup Pport period, at port output (@ Vport = 57 VDC) Imin1 Must disconnect for t greater than TUVL May or may not disconnect for t greater Imin2 than TUVL Zac1 Does not remove power Zac2 Remove power TPMD Buffer period to handle transitions Icut TOVL Trise Toff Time limited to TOVL Typical timer accuracy is 2 ms From 10% to 90% of Vport (specified for PD load consisting of 100 uF capacitor From Vport to 5 Vdc O VL_S I lim Ic u t OVL T cut DC Disconnect Output current consumption below Imin for more than TPMDO (UDL_S to UDL) is categorized as ‘no-load’ and is shutdown. W WW . Microsemi . C OM AC Disconnect A port maintains power if Zac < 27 KΩ A port shutdowns power if Zac > 1980 KΩ for a time period greater than TPMDO. MIN. TYP. 5 1 MAX. UNIT s s 750 10 0.57 0 5 1980 300 660 50 15 500 680 400 700 75 7.5 700 30 5 10 27 mA mA W mA mA KΩ KΩ ms mA ms us ms Ich an n e l P o rt 1 P o rt 2 PD671xx DIMM UDL_S Im in UDL P o rt o ff T m in Figure 4: Power Limits Copyright © 2009 Microsemi Page 6 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Pin Designations __________ The PD671xxx DIMMs have a fit/form based on a JEDEC MO-161f outline. Conventions used in the design are as follows: Power and ground connections are reproduced a number of times to carry heavy currents. Signals are categorized as analog (input or output) or digital (input, output and I/O). All lines which are identified with an “x” prefix are active when logical is low. Refer to Figure 5. W WW . Microsemi . C OM PD671xx DIMM Figure 5: Pinout Copyright © 2009 Microsemi Page 6 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Pin Description Signals are categorized as ‘analog’ (input or output) or ‘digital’ (input, output and I/O). Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Vmain Main V+ input Pin Name Pin Type Pin Description Pin 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 100 111 112 113 114 115 116 117 118 119 120 121 122 123 124 Pin Name Pin Type Pin Description W WW . Microsemi . C OM Vmain Main V+ input Power input Power input Vmain_ret Main V return Vmain_ret Main V return Port_P0 Port_N0 Port_P1 Port_N1 Port_P2 Port_N2 Port_P3 Port_N3 Port_P4 Port_N4 Port_P5 Port_N5 Port_P6 Port_N6 Port_P7 Port_N7 Port_P8 Port_N8 Port_P9 Port_N9 Port_P10 Port_N10 Port_P11 Port_N11 TBD TBD ASICINI_4_ Out ASICINI_5_ Out xLed_Cs TBD BKGD DGND xAsic_Reset xReset_In ASICINI_0_ Out ASICINI_1_ Out ASICINI_2_ Out Channel 1 positive output Channel 1 negative output Channel 2 positive output Channel 2 negative output Channel 3 positive output Channel 3 negative output Channel 4 positive output Channel 4 negative output Channel 5 positive output Channel 5 negative output Channel 6 positive output Channel 6 negative output Analog output Channel 7 positive output Channel 7 negative output Channel 8 positive output Channel 8 negative output Channel 9 positive output Channel 9 negative output Channel 10 positive output Channel 10 negative output Channel 11 positive output Channel 11 negative output Channel 12 positive output Channel 12 negative output TBD TBD Determine DIMM 3 managers ESPI address Spare TBD TBD TBD TBD I2C_Addr_0 Qgnd0 CP_0 ASICINI_6_ Out ASICINI_7_ Out xExist Ext_reg 3_3Vout XHswp_On DGND SCK MISO MOSI ASICINI_0_ In ASICINI_1_ In CS0 DGND TBD TBD TBD TBD Digital input Auto mode; sets I2C address Ground Quiet ground Analog output NC (not in use) Determine DIMM 4 managers ESPI address Analog output Digital output Grounded internally- DIMM is present Analog output External regulation for 3.3 V Analog output 3.3 V output to support opto couplers (5 V tolerant) Digital output Connect to MCU Ground Digital ground Digital I/O SPI clock – PD69012 internal comm Digital I/O SPI I/O – PD69012 internal comm Digital I/O SPI I/O – PD69012 internal comm Analog input Determine DIMM managers ESPI address Analog input Determine DIMM managers ESPI address Digital I/O CS for ESPI Ground Digital ground Analog output Digital output Digital input Ground Digital I/O Digital input CS for LED support TBD Factory use only Digital ground Internal reset to PD69012 125 126 127 128 129 130 131 132 133 PD671xx DIMM A reset signal driven by the Host CPU to PoE DIMM Determine DIMM 1 manager Analog output ESPI address Determine DIMM 1 managers Analog output ESPI address Determine DIMM 2 managers Analog output ESPI address Copyright © 2009 Microsemi Page 7 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Pin 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 Pin Name ASICINI_3_ Out HW_Ver_in HW_Ver_out PG1 PG2 I2C_Addr_M TBD SCL DGND Rx2 Tx2 Port_P12 Port_N12 Port_P13 Port_N13 Port_P14 Port_N14 Port_P15 Port_N15 Port_P16 Port_N16 Port_P17 Port_N17 Port_P18 Port_N18 Port_P19 Port_N19 Port_P20 Port_N20 Port_P21 Port_N21 Port_P22 Port_N22 Port_P23 Port_N23 Pin Type Pin Description Pin 134 Pin Name Rx Tx xInt_In xInt_Out ESPI_CS Pin Type Digital input Pin Description UART input Analog input Receives the hardware version Analog output Reports on the hardware version Digital input Indicates PS 1 is good; low= PS bad. Digital input Indicates PS 2 is good; low= PS bad. Analog input Enhanced mode – sets I2C address TBD Digital I/O Ground Digital input I2C clock Digital ground NC (not in use) 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 Digital output UART output Digital input NC (not in use) Digital output Interrupt out signal Digital I/O CS for ESPI between DIMMs W WW . Microsemi . C OM 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Digital output NC (not in use) Analog output Channel 13 positive output Analog output Channel 13 negative output Channel 14 positive output Channel 14 negative output Channel 15 positive output Channel 15 negative output Channel 16 positive output Channel 16 negative output Channel 17 positive output Channel 17 negative output Channel 18 positive output Channel 18 negative output Channel 19 positive output Channel 19 negative output Channel 20 positive output Channel 20 negative output Channel 21 positive output Channel 21 negative output Channel 22 positive output Channel 22 negative output Channel 23 positive output Channel 23 negative output Channel 24 positive output Channel 24 negative output xDisable_Port Digital input Low=disable from host s xSystem_ok Digital output Main DC input status indicator; low = Vmain is out of range. SDA Digital I/O I2C data DGND Ground Digital ground PG3 Digital input Indicates PS 3 is good, low= PS bad TBD TBD CP_1 Analog output NC (not in use) TBD TBD I2C_Addr_1 Digital input Auto mode; sets I2C address Qgnd1 Ground Quiet ground TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD Spare PD671xx DIMM Copyright © 2009 Microsemi Page 8 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Functional Description____________________________________ The following sections detail the PD671xxx DIMM Master functions. System Level W WW . Microsemi . C OM Figure 6 illustrates a 24-port Enhanced mode system based on the PD671xxx DIMM Master. ENHANCED DIMM PD (1 of 24) PD69012 HOST CPU Control Lines ISOLATION I/O UART / I 2C PoE Controller PD69000 PD67124M PD69012 Control Lines Master SPI Bus ENHANCED DIMM PD (25 of 48) PD69012 PD67124S Ethernet Switch PoE System PD69012 Slave Figure 6: PD67124M/S DIMM Configuration Figure 7 illustrates a 24-port Auto mode system based on the PD671xxx DIMM Master. ENHANCED DIMM PD (1 of 24) PD69012 HOST CPU Control Lines ISOLATION I/O I2C Control Lines PD67124AM PD69012 Master SPI Bus ENHANCED DIMM PD (25 of 48) PD69012 PD67124AS Ethernet Switch PoE System PD69012 Slave Figure 7: PD67124AM/AS DIMM Configuration PD671xx DIMM Copyright © 2009 Microsemi Page 9 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Enhanced Mode PD671xxx DIMM Block Diagram Figure 8 illustrates the internal circuitry of the Enhanced Mode DIMM Master. PD69012 appears only in one of the 12 port circuits. W WW . Microsemi . C OM Figure 8: PD67124M DIMM, Internal Block Diagram Top Assembly Description The following sections detail the top assembly components. Number 06-0010-080 provides further details about this design technique. Control Signals Several control signals are utilized between the switch and the PoE circuitry: xReset_In: Driven by the switch circuitry to reset the PoE circuit. xDISABLE_PORTS: Driven by the switch, to disable all PoE ports immediately. Power Supply The entire circuit is powered by a nominal 48 VDC potential (Vmain can range from 44 to 57 VDC for AF mode and 50 to 57 VDC for AT high power mode). 3.3 VDC Regulator Each of the PD69012 includes a 3.3 VDC regulator (EXT_REG and 3_3Vout) for up to 6 mA. This current is utilized for powering external components in the PoE domain. There is an option of adding a driver to this output to drive higher loads. Q1 provides up to 30 mA to the PoE controller and to the opto-couplers in the interface circuit. The total capacitance on the 3.3 VDC should be less then 4.7 uF (with and without an external driver). Indication Signals Int_out: Enables the Host CPU to reduce the communication volume whenever a PoE event masked by the Host CPU occurs. The PoE Controller sends an interrupt for indication. System_ok: (Enhanced mode only) An optional hardware single line, driven by the Master DIMM to the Host CPU; this signal provides the Host CPU with a warning that a major failure such as Vmain out of range has occurred. PD671xx DIMM Grounds The overall circuit includes two physical ground planes, analog and digital, which are electrically connected at a single point on the motherboard (see Figure 9 and Figure 10). This method, used throughout the design, improves noise immunity and coupling. Application note AN-132, Catalogue Copyright © 2009 Microsemi Page 10 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) PD69012 Circuitry All PD69012s work in slave mode, under control of the PD69000G. The PoE Managers, each controlling 12 output ports, are further detailed in Figure 8. The ports can be disabled by the Ethernet switch via the xDisable_Ports signal or by the PoE controller, as required during operation. For further details on the PoE manager, refer to the PoE manager PD69012 Data Sheet, Catalogue Number 06-0072-058. PD671xxx DIMM Evaluation Board __________________ The performance features of Microsemi’s PoE DIMMs can be fully appreciated using the PD671xxx - DIMM Evaluation Board. The Evaluation Board allows the designer to evaluate all of the DIMMs accessible functions. Enhanced mode configuration for up to 48 ports is supported. W WW . Microsemi . C OM AC Disconnect Diodes When deploying an application that utilizes the AC disconnect method, carefully select the diode type and diode location on the mother board. The diode should be located away from the DIMM to prevent mutual heating and the ventilation should be doubled to deal with higher power dissipation. The AC disconnect diode should be connected as shown in Figure 9. Applications_______________ The DIMMs can be integrated into a number of applications, ranging from daughter boards to full integration into Ethernet switches. Examples of such applications are as follows: Integrated directly into a switch: Facilitates the entire PoE concept by including the DIMMs on the main switch PCB. Daughter board add-on: DIMMs are integrated into a small PCB for PoE, mounted on top of the switch’s main PCB. Midspan units: Stand-alone devices, installed between the Ethernet switch and powered devices (telephone, camera, wireless LAN, etc.). These Midspan units include the DIMMs as a PoE control element, injecting power over the communication lines. DC Disconnect Using the DC disconnect method, the mother board should contain a short circuit between Vmain coming from the power supply and Port_P[0-23] as illustrated in Figure 10. Figure 9: Overall PD671xxx DIMM at AC Disconnect Wiring Diagram Figure 10: Overall PD671xxx DIMM at DC Disconnect Wiring Diagram PD671xx DIMM Copyright © 2009 Microsemi Page 11 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) Power Dissipation______________________________________ The PD671xxx power dissipation is concentrated within a few components distributed along the board as follows. These power dissipation calculations are based on a 24 port DIMM supplied by a 48 VDC power supply and located at ambient temperature of 70° C. COMPONENT DESCRIPTION UNITS POWER DISSIPATION [W] IEEE802.3AF IEEE802.3AT IEEE802.3AT 0.35A/PORT 0.6A/PORT 0.65A/PORT W WW . Microsemi . C OM Rs Senses resistor Mosfet PoE switching Mosfet PD69012 PoE manager PD69000 PoE controller Total * Enhanced mode Master board only 24 24 2 1* 1.43 0.56 1.15 0.02 3.16 4.21 1.64 1.15 0.02 7.02 4.94 1.93 1.15 0.02 8.04 Important: When deploying an application utilizing the AC disconnect method, carefully select the diode type and diode location on the mother board. The diode should be located away from the DIMM to prevent mutual heating and the ventilation should be doubled to deal with higher power dissipation. AC disconnect diodes power dissipation is based on 1 VDC forward voltage. COMPONENT DESCRIPTION UNITS POWER DISSIPATION [W] IEEE802.3AF IEEE802.3AT IEEE802.3AT 0.35A/PORT 0.6A/PORT 0.65A/PORT Diode AC disconnect diode 24 8.4 14.4 15.6 Physical Information ___________________________________ Figure 11 shows the PD671xxx DIMM mechanical outline, which can be used in printed circuit layout design. PD671xxx DIMMs are designed to be mounted onto a 168-contact DIMM connector, capable of accepting JEDEC MO-161 modules. All units are in millimeters. Figure 11: DIMM Dimensions PD671xx DIMM Figure 12: Mechanical Outline of the PD671xxx DIMM Copyright © 2009 Microsemi Page 12 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 PD671xxx - 8 / 12 / 24-Channel PoE AF and AT DIMM Data Sheet (Non-confidential) W WW . Microsemi . C OM Revision History Revision Level / Date 0.1 / Oct. 1 , 2009 0.2 / Oct. 29 , 2009 1.0 / 17-March-10 Para. Affected Description Initial release Overall doc Formal release © 2009 Microsemi Corp. All rights reserved. For support contact: sales_AMSG@microsemi.com Visit our web site at: www.microsemi.com Catalogue Number: 06-0021-058 PD671xx DIMM Copyright © 2009 Microsemi Page 13 Rev. 1.0 / 17-March-10 Analog Mixed Signal Group 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308