SG120-12R

SG120 NEGATIVE FIXED VOLTAGE REGULATOR DESCRIPTION The SG120 series of negative regulators offer self-contained, fixed-voltage capability with up to 1.5A of load current. With a variety of output voltages and four package options this regulator series is an optimum complement to the SG7800A/ 7800/120 line of three terminal regulators. All protective features of thermal shutdown, current limiting, and safe-area control have been designed into these units and since these regulators require only a single output capacitor or a capacitor and 5mA minimum load for satisfactory performance, ease of application is assured. Although designed as fixed-voltage regulators, the output voltage can be increased through the use of a simple voltage divider. The low quiescent drain current of the device insures good regulation when this method is used, especially for the SG120 series. Utilizing an improved Bandgap reference design, problems have been eliminated that are normally associated with the zener diode references, such as drift in output voltage and large changes in the line and load regulation These devices are available in TO-257 (hermetically sealed TO-220), both isolated and non-isolated), TO-3, TO-39 and TO-66 power packages. FEATURES • • • • • • Output current to 1.5A Excellent line and load regulation Foldback current limiting Thermal overload protection Voltages available: -5V, -12V, -15V Voltages Not Recommended For New Designs: -5.2V, -8V, -18V, -20V • Contact factory for other voltage options HIGH RELIABILITY FEATURES - SG120 ♦ Available to MIL-STD - 883 ♦ Radiation data available ♦ LMI level "S" processing available SCHEMATIC DIAGRAM 11/91 Rev 1.4 6/97 Copyright  1997 1 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 ABSOLUTE MAXIMUM RATINGS (Note 1) Device Output Voltage -5V -5.2V -8V -12V -15V -18V -20V Input Voltage -35V -35V -35V -35V -40V -40V -40V NEGATIVE REGULATOR Input Voltage Differential (Output shorted to ground) 35V 35V 35V 35V 35V 35V 35V Operating Junction Temperature Hermetic (K, R, IG - Packages) ................................... 150°C Note 1. Values beyond which damage may occur. Storage Temperature Range ........................... -65°C to 150°C Lead Temperature (Soldering, 10 Seconds) ................. 300°C THERMAL DATA K Package: Thermal Resistance-Junction to Case, θJC ................. 3.0°C/W Thermal Resistance-Junction to Ambient, θJA ............... 35°C/W R Package: Thermal Resistance-Junction to Case, θJC ................. 5.0°C/W Thermal Resistance-Junction to Ambient, θJA .............. 40°C/W T Package: Thermal Resistance-Junction to Case, θJC .................. 15°C/W Thermal Resistance-Junction to Ambient, θJA ............ 120°C/W IG Package: Thermal Resistance-Junction to Case, θJC ................. 3.5°C/W Thermal Resistance-Junction to Ambient, θJA .............. 42°C/W L Package: Thermal Resistance-Junction to Case, θJC .................. 35°C/W Thermal Resistance-Junction to Ambient, θJA ............ 120°C/W Note A. Junction Temperature Calculation: TJ = TA + (PD x θJA). Note B. The above numbers for θJC are maximums for the limiting thermal resistance of the package in a standard mounting configuration. The θJA numbers are meant to be guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. RECOMMENDED OPERATING CONDITIONS (Note 2) Operating Junction Temperature Range: SG120 ........................................................... -55°C to 150°C Note 2. Range over which the device is functional. CHARACTERISTIC CURVES FIGURE 1. MAXIMUM AVERAGE POWER DISSIPATION FIGURE 2. QUIESCENT CURRENT VS. LOAD FIGURE 3. TEMPERATURE COEFFICIENT 11/91 Rev 1.4 6/97 Copyright  1997 2 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 CHARACTERISTIC CURVES (continued) NEGATIVE REGULATOR FIGURE 4. SHORTCIRCUIT CURRENT VS. VIN FIGURE 5. QUIESCENT CURRENT VS. VIN FIGURE 6. SHORT CIRCUIT CURRENT VS. VIN FIGURE 7. DROPOUT CHARACTERISTICS FIGURE 8. RIPPLE REJECTION VS. FREQUENCY APPLICATIONS FIGURE 9 - FIXED OUTPUT REGULATOR FIGURE 10 - CIRCUIT FOR INCREASING OUTPUT VOLTAGE NOTE: 1. C1 is required only if regulator is separated from rectifier filter. 2. Both C1 and C2 should be low E.S.R. types such as solid tantalum. If aluminum electrolitics are used, at least 10 times values shown should be selected. 3. If large output capacities are used, the regulators must be protected from momentary input shorts. A high current diode from output to input will suffice. NOTE: C3 optional for improved transient response and ripple rejection. R + R2 V(REG) R2 = VOUT = V (REGULATOR) 1 R1 15mA 11/91 Rev 1.4 6/97 Copyright  1997 3 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 ELECTRICAL CHARACTERISTICS SG120-05 (Note 1) -5.0V & -5.2V NEGATIVE REGULATOR (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-05 with -55°C ≤ TA ≤ 150°C, and VIN = -10V, IO = 5mA, CIN = 2mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -7V to -25V, TJ = 25°C Power Pkgs: IO = 5mA to 1.5A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -7.5V to -25V Power Pkgs: IO = 5mA to 1.5A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -7V to -25V With Line: VIN = -7V to -25V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.5A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-05 Min. Typ. Max. -4.9 -5.0 -5.1 10 25 50 75 30 50 -4.8 -4.8 -5.0 -5.0 -5.2 -5.2 2 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 80 Units V mV mV mV V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown SG120-5.2 54 25 20 175 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-5.2 with -55°C ≤ TA ≤ 150°C, and VIN = -10V, IO = 5mA, CIN = 2mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -7.2V to -25V, TJ = 25°C Power Pkgs: IO = 5mA to 1.5A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -7.7V to -25V Power Pkgs: IO = 5mA to 1.5A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -7.2V to -25V With Line: VIN = -7.2V to -25V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.5A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.5A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-5.2 Min. Typ. Max. -5.1 -5.2 -5.3 15 25 50 75 30 50 -5.0 -5.0 -5.2 -5.2 -5.4 -5.4 2 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 80 Units V mV mV mV V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown 54 25 20 175 Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. 11/91 Rev 1.4 6/97 Copyright  1997 4 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 ELECTRICAL CHARACTERISTICS SG120-08 (Note 1) -8V & -12V NEGATIVE REGULATOR (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-08 with -55°C ≤ TA ≤ 150°C, and VIN = -14V, IO = 5mA, CIN = 1.0mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -10.5V to -25V, TJ = 25°C Power Pkgs: IO = 5mA to 1.5A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -10.5V to -25V Power Pkgs: IO = 5mA to 1.5A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -10.5V to -25V With Line: VIN = -10.5V to -25V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.5A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-8 Min. Typ. Max. -7.8 -8.0 -8.2 10 25 20 80 10 25 -7.65 -8.00 -8.35 -7.65 -8.00 -8.35 2 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 80 Units V mV mV mV V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown SG120-12 54 25 32 175 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-12 with -55°C ≤ TA ≤ 150°C, and VIN = -17V, IO = 5mA, CIN = 2.0mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -14V to -32V, TJ = 25°C Power Pkgs: IO = 5mA to 1.0A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -14.5V to -32V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -14V to -32V With Line: VIN = -14V to -32V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.0A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-12 Min. Typ. Max. -11.7 -12.0 -12.3 4 10 30 80 10 25 -11.5 -12.0 -12.5 -11.5 -12.0 -12.5 2 4 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 80 Units V mV mV mV V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown 56 25 48 175 Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. 11/91 Rev 1.4 6/97 Copyright  1997 5 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 ELECTRICAL CHARTACTERISTICS SG120-15 (Note 1) -15V & -18V NEGATIVE REGULATOR (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-15 with -55°C ≤ TA ≤ 150°C, and VIN = -20V, IO = 5mA, CIN = 2.0mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -17V to -35V, TJ = 25°C Power Pkgs: IO = 5mA to 1.0A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -17.5V to -35V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -17V to -35V With Line: VIN = -17V to -35V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.0A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-15 Min. Typ. Max. -14.7 -15.0 -15.3 5 10 30 80 10 25 -14.5 -15.0 -15.5 -14.5 -15.0 -15.5 2 4 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 80 Units V mV mV mV V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown SG120-18 56 25 60 175 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-18 with -55°C ≤ TA ≤ 150°C, and VIN = -27V, IO = 5mA, CIN = 2.0mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -21V to -33V, TJ = 25°C Power Pkgs: IO = 5mA to 1.0A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -22V to -33V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -21V to -33V With Line: VIN = -21V to -33V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.0A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-18 Min. Typ. Max. -17.6 -18.0 -18.4 5 10 30 80 10 25 -17.4 -18.0 -18.6 -17.4 -18.0 -18.6 2 4 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 Units V mV mV mV V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown 56 25 72 175 Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. 11/91 Rev 1.4 6/97 Copyright  1997 6 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 ELECTRICAL CHATRACTERISTICS SG120-20 (Note 1) -20V NEGATIVE REGULATOR (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG120-20 with -55°C ≤ TA ≤ 150°C, and VIN = -29V, IO = 5mA, CIN = 2.0mF, COUT = 1.0mF. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Test Conditions TJ = 25°C VIN = -23V to -35V, TJ = 25°C Power Pkgs: IO = 5mA to 1.0A, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = -24V to -35V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W VIN = -23V to -35V With Line: VIN = -23V to -35V, TJ = 25°C With Load: TJ = 25°C Power Pkgs: IO = 5mA to 1.0A T - Pkg: IO = 5mA to 500mA ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = -35V, TJ = 25°C T - Pkg: VIN = -35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG120-20 Units Min. Typ. Max. -19.5 -20.0 -20.5 V 5 10 mV 30 80 mV 10 25 mV -19.3 -20.0 -20.7 -19.3 -20.0 -20.7 2 4 0.4 0.4 0.4 1.1 1.5 0.5 2.3 3.3 1.4 1.2 0.6 80 V V mA mA mA mA V A A A A dB µV/V mV °C Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown 56 25 80 175 Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. 11/91 Rev 1.4 6/97 Copyright  1997 7 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc. SG120 CONNECTION DIAGRAMS & ORDERING INFORMATION Package 3-TERMINAL TO-3 METAL CAN K-PACKAGE NEGATIVE REGULATOR (See Notes Below) Part No. SG120-XXK/883B SG120-XXK Ambient Temperature Range -55°C to 125°C -55°C to 125°C Connection Diagram GROUND 1 2 CASE IS VIN VOUT 3-TERMINAL TO-66 METAL CAN R-PACKAGE SG120-XXR/883B SG120-XXR -55°C to 125°C -55°C to 125°C GROUND 1 2 CASE IS VIN VOUT 3-PIN TO-39 METAL CAN T-PACKAGE SG120-XXT/883B SG120-XXT -55°C to 125°C -55°C to 125°C GROUND VOUT 1 2 3 VIN CASE IS VIN 3-PIN HERMETIC TO-257 IG-PACKAGE (Isolated) SG120-XXIG/883B SG120-XXIG -55°C to 125°C -55°C to 125°C VOUT VIN GROUND 20-PIN CERAMIC (LCC) LEADLESS CHIP CARRIER L- PACKAGE SG120-XXL/883B SG120-XXL -55°C to 125°C -55°C to 125°C (Note 4) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. N.C. VIN N.C. VOUT VOUT N.C. VOUT SENSE N.C. N.C. N.C. 3 2 1 20 19 18 17 16 15 14 4 5 6 7 8 9 10 11 12 13 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. N.C. N.C. N.C. N.C. GND N.C. GND N.C. N.C. VIN Note 1. 2. 3. 4. Contact factory for JAN and DESC product availability. All parts are viewed from the top. "XX" to be replaced by output voltage of specific fixed regulator. Some products will be available in leadless chip carrier (LCC) and hermetic flat pack (F). Consult factory for price and availability 11/91 Rev 1.4 6/97 Copyright  1997 8 11861 Western L IN F IN ITY Avenue ∞ G arden Grove, CA 92841 (714) 898-8121 F AX: (714) 893-2570 ∞ M icroelectronics Inc.