867-10-003-70-502011

www.mill-max.com DATA SHEET PRODUCT NUMBER: 867-10-003-70-502011 867-10-003-70-502011- SPECIFICATIONS General Info Materials Shell Plating: Description 1 : Wire Termination Target Header Pre-Wired with 8" 24 AWG Black Stranded Wires Type: Spring-Loaded Category: Crimped Wire Cable Assembly Mounting Style: Wire Termination - Crimp Type # Pins: 3 Pitch: .100" (2,540mm) Rows: Single Row Product Lifecycle: Active 10 μ" Gold over 100 μ" Nickel Inner Plating: Insulator Material: Nylon 4/6 Electrical Specs Rated Voltage: 100 VRMS/150 VDC Insulation Resistance: 10,000 MΩ min. Dielectric Withstanding Voltage: 1,000 VRMS min. Environmental Specs Temperature Range2 : -55/+125° C Shock3 : No Elect. Discontinuity > 1μs @ 50g Vibration3 : No Elect. Discontinuity > 1μs @ 10-2000HZ, 15 G RoHS4 : Yes Product Number 867-10-003-70-502011 Data Sheet (c)2022 Mill-Max Mfg Corp. | 516-922-6000 190 Pine Hollow Road, Oyster Bay, NY 11771 Updated 10/17/22 12:17 PM EDT - Page 1 of 2 NOTES: 1. Standard Tolerances Assembly tolerance: +/-.010" (.25mm) Connector Length “L” Connector Length “L” Tolerance L ≤ 2” (L ≤ 50.8 mm) +/- .005” (+/- .127 mm) 2< L ≤ 3” (50.8 < L ≤ 76.2 mm) + .007/ - .006” (+ .178/ -.152 mm) 3< L ≤ 4” (76.2 < L ≤ 101.6 mm) + .009 / - .007” (+ .229 / - .178 mm) 4< L ≤ 5” (101.6 < L ≤ 127 mm) + .011 / - .008” (+ .279 / - .203 mm) 5< L ≤ 6.4” (127 < L ≤ 162.56 mm) + .013 / - .009” (+ .330 / - .229 mm) Insulator width: +/-.005 (.13mm) Insulator height: +/-.005 (.13mm) Co-planarity of SMT connectors: .005" (.13mm) up to 1" (25.4mm) in connector length Insulator Flatness: .005" (.13mm) up to 1" (25.4mm) in connector length Pin Length: +/-.005 (.13mm) Pin Diameter: +/-.002 (.051mm) Pin Angle: +/-2° 2. Per IEC 60512-11-(4,-9,-10,-12) 3. For discrete pin only. Per IEC 60512-6-3: Test 6c: Shock 4. Mill-Max products labeled with the RoHS symbol are compliant with all three ROHS Directives. All of our products previously described as RoHS (2002/95/EC) and RoHS-2 (2011/65/EC) are also compliant with RoHS-3 (2015/863/EU). ADDITIONAL NOTES AND SPECIFICATIONS In the interest of improved design, quality and performance , Mill-Max reserves the right to make changes in its specifications without prior notice. Specifications and tolerances are provided wherever possible. The tolerance on dimensions of critical to function features is typically held tighter than the stated standard tolerances, such as press-fits, holes and lengths affecting the coplanarity of SMT products. Due to the wide variety of interconnects Mill-Max offers, the specific tolerances vary from product to product. If you need information regarding the tolerance of a particular part, please contact Technical Services. RELATED LINKS AND DOCUMENTS Engineering Notebook: ( https://www.mill-max.com/engineering-notebooks/introduction-to-spring-loaded-pogo-pins-connectors ) Environmental Compliance: ( https://www.mill-max.com/rohs ) Product Number 867-10-003-70-502011 Data Sheet (c)2022 Mill-Max Mfg Corp. | 516-922-6000 190 Pine Hollow Road, Oyster Bay, NY 11771 Updated 10/17/22 12:17 PM EDT - Page 2 of 2