LHA-23LN+

ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier 50Ω LHA-23LN+ 30 MHz to 2 GHz THE BIG DEAL y Ultra-High IP3, +36.9 dBm typ y Gain, 21.2 dB typ. at 1 GHz y Low noise figure, 1.2 dB at 1 GHz y Low voltage, 5V and 3V. Generic photo used for illustration purposes only CASE STYLE: DQ1225 +RoHS Compliant The +Suffix identifies RoHS Compliance. See our web site for RoHS Compliance methodologies and qualifications APPLICATIONS y Base station infrastructure y CATV y Cellular PRODUCT OVERVIEW LHA-23LN+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the LHA-23LN+ has good input and output return loss over a broad frequency range. LHA-23LN+ is enclosed in a 3mm x 3mm, 12-lead MCLP package and has very good thermal performance. KEY FEATURES Feature Advantages Broad Band: 30MHz to 2GHz Broadband covering primary wireless communications bands: VHF, UHF, Cellular Extremely High IP3 40.3 dBm typical at 0.5 GHz 36.9 dBm typical at1GHz The LHA-23LN+ matches industry leading IP3 performance relative to device size and power consumption. The combination of the design and E-PHEMT Structure provides enhanced linearity over a broad frequency range as evidence in the IP3 being approximately 11-17 dB above the P1dB point. This feature makes this amplifier ideal for use in: y Driver amplifiers for complex waveform up converter paths y Drivers in linearized transmit systems y Secondary amplifiers in ultra-High Dynamic range receivers Low Noise Figure 1.2 dB at 1 GHz Enables lower system noise figure performance and along with High OIP3 provides high dynamic range Low Supply Voltage LHA-23LN+ supports low supply voltage operation which indicate low power consumption. REV. A ECO-011665 LHA-23LN+ MCL NY 220124 www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 1 OF 4 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier LHA-23LN+ ELECTRICAL SPECIFICATIONS1 AT 25°C, 50Ω, UNLESS NOTED OTHERWISE Condition (MHz) Parameter Frequency Range 30 500 1000 1500 2000 30 500 1000 1500 2000 30 500 1000 1500 2000 1000 30 500 1000 1500 2000 30 500 1000 1500 2000 30 500 1000 1500 2000 Gain Input Return Loss Output Return Loss Reverse isolation Output Power @1 dB compression Output IP3 2 Noise Figure Vd=5V1 Min. 30 — — 18.9 18.1 — Device Operating Voltage Device Operating Current Device Current Variation vs. Temperature3 Device Current Variation vs Voltage Thermal Resistance, junction-to-ground lead Junction-to-ground lead at 85°C stage temperature Typ. 23.0 21.9 21.2 20.4 19.6 12 11 10 10 10 14 15 19 15 11 26.9 22.8 24.2 23.8 23.2 23.0 39.8 39.0 36.9 35.2 34.6 1.0 1.1 1.2 1.3 1.5 5.0 146 -26.1 0.0359 23.3 Vd=3V1 Max. 2000 — — 23.1 22.1 — 162 Units Typ. 30-2000 22.3 21.1 19.9 18.8 17.6 12 11 8 7 8 16 18 23 13 9 26.6 17.1 19.2 18.8 18.4 18.0 33.9 33.5 31.6 30.7 30.0 1.0 1.1 1.2 1.3 1.6 3.0 75 17.5 0.0364 V mA µA/°C mA/mV 23.3 °C/W MHz dB dB dB dB dBm dBm dB 1. Measured on Mini-Circuits Characterization test board TB-1061-23LN+. See Characterization Test Circuit (Fig. 1) 2. Tested at Pout= 0 dBm / tone. 3. (Current at 105°C — Current at -45°C)/150 MAXIMUM RATINGS4 Parameter Ratings Operating Temperature (ground lead) -40°C to 105°C Storage Temperature -65°C to 150°C Power Dissipation5 Input Power (CW) DC Voltage on Pin 7 3.3W +22 dBm (5 minutes max)6 +4 dBm (continuous) for 0.03-1GHz at 3V +8 dBm (continuous) for 0.03-1GHz at 5V +12 dBm (continuous) for 1-2GHz at 3V +15 dBm (continuous) for 1-2GHz at 5V 10V 4. Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are not intended for continuous normal operation. 5. Up to 85°C, derate linearly to 2.5W at 105°C. 6. Up to 85°C, derate linearly to +19dBm at 105°C. www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 2 OF 4 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier LHA-23LN+ SIMPLIFIED SCHEMATIC AND PAD DESCRIPTION NC NC NC 12 RF-OUT and DC-IN RF-IN 11 10 NC 1 9 NC NC 2 8 NC RF-IN 3 7 RF-OUT & DC-IN GND 4 5 6 NC NC NC Function Pad Number Description RF-IN 3 RF Input RF-OUT and DC-IN 7 RF Output and DC Bias GND Paddle Connections to ground. NC 1-2, 4-6, 8-12 No connection, grounded externally CHARACTERIZATION TEST / RECOMMENDED APPLICATION CIRCUIT Vdd C6 1-2,4-6,8-12 & Paddle RF-IN L2 C2 3 DUT 7 Fig 1. Block Diagram of Test Circuit used for characterization. (DUT soldered on Mini-Circuits Characterization test board TB-1061-23LN+) Gain, Return loss, Output power at 1dB compression (P1 dB), output IP3 (OIP3) and noise figure measured using Agilent’s N5242A PNA-X microwave network analyzer. C5 L1 RF-OUT C4 C1 Conditions: 1. Gain and Return loss: Pin= -25dBm 2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 0 dBm/ tone at output. Components C3 Size C1 R1 Manufacturer 1.2pF C2,C3,C6 C4 Value 0.1uF 0402 0.001uF C5 0.01uF R1 1.21KOhm L1 0805 0.68uH L2 0402 1nH P/N GRM1555C1H1R2WA01D Murata GRM155R71C104KA88D GRM1555C1H102JA01D GRM155R71E103KA01D KOA Coilcraft RK73H1ETTP1211F 0805LS-681XJLB 0402CS-1N0XJLW PRODUCT MARKING Index over pin MCL 23LN Black body Model family designation Marking may contain other features or characters for internal lot control www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 3 OF 4 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier LHA-23LN+ ADDITIONAL DETAILED TECHNICAL INFORMATION IS AVAILABLE ON OUR DASH BOARD. TO ACCESS Performance Data Data Table Swept Graphs Case Style DQ1225 Plastic package, exposed paddle lead finish: Matte-Tin Tape & Reel Standard quantities available on reel F66 7” reels with 20, 50, 100, 200, 500, 1K, or 2K devices Suggested Layout for PCB Design PL-587 Evaluation Board TB-1061-23HLN+ Environmental Ratings ENV08T9 C LIC K HERE ESD RATING Human Body Model (HBM): Class 1B (Pass 500 V) in accordance with ANSI/ESD STM 5.1 - 2001 MSL RATING Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D MSL FLOW CHART Start Visual Inspection Electrical Test SAM Analysis Reflow 3 cycles 260°C Soak 85°C/85RH 168 hours Bake at 125°C, 24 hours Visual Inspection Electrical Test SAM Analysis Finish NOTES A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the standard. Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 4 OF 4