PHA-13HLN+

Ultra High Dynamic Range Monolithic Amplifier 50Ω PHA-13HLN+ 1MHz to 1 GHz The Big Deal • Ultra-High IP3, +43 dBm typ. • Medium Power, +28.7dBm typ. • Excellent Noise Figure, 1.1 dB typ. SOT-89 PACKAGE Product Overview PHA-13HLN+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-13HLN+ has good input and output return loss over a broad frequency range. PHA-13HLN+ is enclosed in a SOT-89 package and has very good thermal performance. Key Features Feature Advantages Broad Band: 1MHz to 1GHz Broadband covering primary wireless communications bands: VHF, UHF, Cellular Extremely High IP3 38.4 dBm typical at 1MHz 43 dBm typical at 0.5GHz The PHA-13HLN+ matches industry leading IP3 performance relative to device size and power consumption. The combination of the design and E-PHEMT Structure provides enhanced linearity over a broad frequency range as evidence in the IP3 being approximately 15 dB above the P1dB point. This feature makes this amplifier ideal for use in: • Driver amplifiers for complex waveform up converter paths • Drivers in linearized transmit systems • Secondary amplifiers in ultra-High Dynamic range receivers Low Noise Figure 1.1 dB at 0.5 GHz Enables lower system noise figure performance High P1dB 28.7 dBm at 500 MHz High P1dB, High OIP3, Low NF results in a very dynamic range preventing amplifier saturation under strong interfering signals. It can also be used to drive mixers requiring high drive Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 1 of 5 Ultra High Dynamic Range Monolithic Amplifier 1MHz to 1 GHz Product Features •High IP3, 43 dBm typ. at 0.5GHz •Gain, 22.7 dB typ. at 0.5 GHz •High Pout, P1dB 28.7 dBm typ. at 0.5GHz •Low noise figure, 1.1 dB at 0.5 GHz Generic photo used for illustration purposes only CASE STYLE: DF782 PHA-13HLN+ Typical Applications +RoHS Compliant •Base station infrastructure •CATV •Cellular The +Suffix identifies RoHS Compliance. See our web site for RoHS Compliance methodologies and qualifications General Description PHA-13HLN+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-13HLN+ has good input and output return loss over a broad frequency range. PHA-13HLN+ is enclosed in a SOT-89 package and has very good thermal performance. simplified schematic and pin description 3 RF-OUT & DC-IN RF-OUT and DC-IN RF-IN 2 GROUND 4 1 RF-IN GND Function Pin Number Description RF IN 1 RF Input RF-OUT and DC-IN 3 RF Output and DC Bias GND 2,4 Connections to ground. Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com REV. OR M159854 PHA-13HLN+ MCL NY 171129 Page 2 of 5 PHA-13HLN+ Monolithic E-PHEMT MMIC Amplifier Electrical Specifications1 at 25°C, 50Ω, unless noted Condition (MHz) Parameter Min. Frequency Range 1 22.4 — — 20.4 — 1 20 250 500 1000 1 20 250 500 1000 1 20 250 500 1000 Gain Input Return Loss Output Return Loss Reverse isolation Output Power @1 dB compression Output IP3 2 Noise Figure Vd=8V1 Typ. 25.0 24.3 23.0 22.7 20.4 10.8 15.8 16.7 17.5 10.5 11.2 18.8 17.7 29.4 9.0 500 26.3 1 20 250 500 1000 1 20 250 500 1000 1 20 26.2 27.3 28.4 28.7 27.4 38.4 41.7 43.5 43.0 42.2 3.0 1.2 — — — 40.0 — 250 1.1 500 1000 1.1 1.4 8.0 234.1 -100.6 0.0155 Device Operating Voltage Device Operating Current Device Current Variation vs. Temperature3 Device Current Variation vs Voltage — Thermal Resistance, junction-to-ground lead Junction-to-ground lead at 85°C stage temperature Units Max. 1000 27.4 — — 25.0 — MHz dB dB dB dB dBm — — — — — dBm dB 251 23.3 V mA µA/°C mA/mV °C/W 1. Measured on Mini-Circuits Characterization test board TB-969-13HLN+. See Characterization Test Circuit (Fig. 1) 2. Tested at Pout= 0 dBm / tone. 3. (Current at 85°C — Current at -45°C)/130 Absolute Maximum Ratings4 Parameter Ratings Operating Temperature (ground lead) Storage Temperature Power Dissipation Input Power (CW) DC Voltage on Pin 3 -40°C to 95°C -65°C to 150°C 3.3 W5 +21 dBm (5 minutes max)6 +10 dBm (continuous) for 1-10 MHz +11 dBm (continuous) for 10-1000 MHz 10V 4. Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are not intended for continuous normal operation. 5. up to 85°C, derate linearly to 2.5 W at 95°C. 6. up to 85°C, derate linearly to 18 dBm at 95°C. Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 3 of 5 PHA-13HLN+ PHA-13HLN+ Monolithic E-PHEMT MMIC Amplifier Monolithic E-PHEMT MMIC Amplifier Characterization Test / Recommended Application Characterization Test/Recommended ApplicationCircuit Circuit A Fig 1. Block Diagram of Test Circuit used for characterization. (DUT soldered on Mini-Circuits Characterization test board TB-969-13HLN+) Fig 1.loss, Block Diagram Circuit used(P1dB), for characterization. soldered onmeasured Mini-Circuits board TB-969-13HLN+) Gain, Return Output powerofatTest 1dB compression output IP3 (OIP3)(DUT and noise figure usingCharacterization Agilent’s N5242Atest PNA-X Gain, Return loss, Output power at 1dB compression (P1 dB), output IP3 (OIP3) and noise figure measured using Agilent’s N5242A microwave network analyzer. PNA-X microwave network analyzer. Conditions: 1. Gain Conditions: and Return loss: Pin= -25dBm 1. IP3 Gain and Return loss:spaced Pin= -25dBm 2. Output (OIP3): Two tones, 0.5 MHz apart, 0 dBm/ tone at output. 2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 0 dBm/ tone at output. Product Marking Product Marking PH23PH23 Marking maymay contain otherother features or characters for internal lot control Marking contain features or characters for internal lot control Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits Mini-Circuits ® ® www.minicircuits.com P.O. 350166, Box 350166, Brooklyn, NY 11235-0003 934-4500 sales@minicircuits.com www.minicircuits.com P.O. Box Brooklyn, NY 11235-0003 (718)(718) 934-4500 sales@minicircuits.com Page 4 Page of 5 4 of 5 PHA-13HLN+ Monolithic E-PHEMT MMIC Amplifier Additional Detailed Technical Information additional information is available on our dash board. To access this information click here Data Table Performance Data Swept Graphs S-Parameter (S2P Files) Data Set (.zip file) DF782 (SOT 89) Case Style Plastic package, exposed paddle lead finish: Matt-Tin Tape & Reel F55 Standard quantities available on reel 7” reels with 20, 50, 100, 200, 500 or 1K devices Suggested Layout for PCB Design PL-523 Evaluation Board TB-969-13HLN+ Environmental Ratings ENV08T9 ESD Rating Human Body Model (HBM): Class 1B (Pass 500 V) in accordance with ANSI/ESD STM 5.1 - 2001 MSL Rating Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D MSL Test Flow Chart Start Visual Inspection Electrical Test SAM Analysis Reflow 3 cycles, 260°C Soak 85°C/85RH 168 hours Bake at 125°C, 24 hours Visual Inspection Electrical Test SAM Analysis Stop Additional Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms Notes and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. containedandtherein. For adata fullcontained statement the Standard Terms and the exclusive rights and remedies B. Electrical specifications performance in thisofspecification document are based on Mini-Circuit’s applicable established testthereunder, performance criteria and measurement instructions. C. The parts covered by this document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled please visitspecification Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 5 of 5