PHA-13LN+

ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier 50Ω PHA-13LN+ 1MHz to 1GHz THE BIG DEAL y Ultra-High IP3, +39 dBm typ. y Low supply voltage, 3 to 5V y Excellent Noise Figure, 0.9 dB typ. Generic photo used for illustration purposes only CASE STYLE: DF782 APPLICATIONS y Base station infrastructure y CATV y Cellular y VHF/UHF +RoHS Compliant The +Suffix identifies RoHS Compliance. See our web site for RoHS Compliance methodologies and qualifications PRODUCT OVERVIEW PHA-13LN+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-13LN+ has good input and output return loss over a broad frequency range. Relatively low supply voltage gives the model advantage in low power consumption. PHA-13LN+ is enclosed in a SOT-89 package and has very good thermal performance. KEY FEATURES Feature Advantages Broad Band: 1MHz to 1GHz Broadband covering primary wireless communications bands: VHF, UHF, Cellular Extremely High IP3 40 dBm typical at 20 MHz 39 dBm typical at 0.5GHz The PHA-13LN+ matches industry leading IP3 performance relative to device size and power consumption. The combination of the design and E-PHEMT Structure provides enhanced linearity over a broad frequency range as evidence in the IP3 being approximately 15 dB above the P1dB point. This feature makes this amplifier ideal for use in: y Driver amplifiers for complex waveform up converter paths y Drivers in linearized transmit systems y Secondary amplifiers in ultra-High Dynamic range receivers Low Noise Figure 0.9 dB at 0.5 GHz Enables lower system noise figure performance and along with High OIP3 provides high dynamic range. Low Supply Voltage, 3 to 5V PHA-13LN+ supports low supply voltage operation which indicate low power consumption, 3V operation is ideal for battery operated system. REV. A ECO-010399 M159854 PHA-13LN+ MCL NY 211028 www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 1 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-13LN+ ELECTRICAL SPECIFICATIONS1 AT 25°C, 50Ω, UNLESS NOTED Parameter Min. 1 22.1 24.6 Frequency Range Gain Input Return Loss Output Return Loss Reverse isolation Output Power @1 dB compression Output IP3 2 Noise Figure Vd=5V1 Condition (MHz) 1 Device Current Variation vs. Temperature3 Device Current Variation vs Voltage Thermal Resistance, junction-to-ground lead Junction-to-ground lead at 85°C stage temperature Vd=3V1 Max. Typ. 1000 1-1000 27.1 23.7 20 — 24.0 — 23.3 250 — 22.8 — 22.1 500 20.2 22.4 24.6 21.5 1000 — 20.1 — 18.7 1 10.3 9.4 20 15.4 14.6 250 17.5 17.9 500 17.4 14.7 1000 10.2 7.9 1 11.3 11.0 20 19.1 21.5 250 17.7 20.2 500 23.9 20.0 1000 8.9 7.8 500 26.1 25.7 1 21.3 15.1 20 23.0 16.9 250 24.4 19.5 500 24.5 19.5 1000 24.2 — 37.0 — 30.6 20 — 40.2 — 33.3 250 — 40.2 — 33.4 500 36 39.0 — 32.3 1000 — 36.4 — 28.6 1 3.1 3.0 20 1.2 1.1 250 0.9 0.9 500 1.0 1.0 1000 1.2 1.3 5.0 — 138.9 Units MHz dB dB dB dB dBm 18.7 1 Device Operating Voltage Device Operating Current Typ. 162 dBm dB 3.0 V 71.2 mA 21.7 30.3 µA/°C 0.0338 0.0338 mA/mV 23.3 23.3 °C/W www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 2 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-13LN+ MAXIMUM RATINGS4 Parameter Ratings Operating Temperature (ground lead) -40°C to 105°C Storage Temperature -65°C to 150°C Power Dissipation 3.3 W5 Input Power (CW) +21 dBm (5 minutes max)6 +6 dBm (continuous) for 1-10 MHz +8 dBm (continuous) for 10-1000 MHz DC Voltage on Pin 3 10V 4. Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are not intended for continuous normal operation. 5. up to 85°C, derate linearly to 2.5 W at 95°C. 6. up to 85°C, derate linearly to 18 dBm at 95°C. SIMPLIFIED SCHEMATIC AND PIN DESCRIPTION 3 RF-OUT & DC-IN RF-OUT and DC-IN RF-IN 4 2 GROUND 1 RF-IN GND Function Pin Number Description RF IN 1 RF Input RF-OUT and DC-IN 3 RF Output and DC Bias GND 2,4 Connections to ground. 1. Measured on Mini-Circuits Characterization test board TB-969-13LN+. See Characterization Test Circuit (Fig. 1) 2. Tested at Pout= 0 dBm / tone. 3. (Current at 85°C — Current at -45°C)/130 www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 3 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-13LN+ CHARACTERIZATION TEST / RECOMMENDED APPLICATION CIRCUIT Vdd C6 C5 4 L2 RF-IN C2 1 3 DUT L1 RF-OUT C4 C1 2 C3 R1 Fig 1. Block Diagram of Test Circuit used for characterization. (DUT soldered on Mini-Circuits Characterization test board TB-969-13LN+) Gain, Return loss, Output power at 1dB compression (P1dB), output IP3 (OIP3) and noise figure measured using Agilent’s N5242A PNA-X microwave network analyzer. Conditions: 1. Gain and Return loss: Pin= -25dBm 2. Output IP3 (OIP3): Two tones, spaced 0.5 MHz apart, 0 dBm/ tone at output. PRODUCT MARKING PH23 Marking may contain other features or characters for internal lot control www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 4 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-13LN+ ADDITIONAL DETAILED TECHNICAL INFORMATION IS AVAILABLE ON OUR DASH BOARD. TO ACCESS C LIC K HERE Data Table Performance Data Swept Graphs S-Parameter (S2P Files) Data Set (.zip file) Case Style DF782 (SOT 89) Plastic package, exposed paddle lead finish: matte-tin Tape & Reel Standard quantities available on reel F55 7” reels with 20, 50, 100, 200, 500 or 1K devices Suggested Layout for PCB Design PL-523 Evaluation Board TB-969-13LN+ Environmental Ratings ENV08T9 ESD RATING Human Body Model (HBM): Class 1B (Pass 500 V) in accordance with ANSI/ESD STM 5.1 - 2001 MSL RATING Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D MSL TEST FLOW CHART Start Visual Inspection Electrical Test SAM Analysis Reflow 3 cycles 260°C Soak 85°C/85RH 168 hours Bake at 125°C, 24 hours Visual Inspection Electrical Test SAM Analysis Finish NOTES A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the standard. Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 5 OF 5