PHA-1H+

Ultra High Dynamic Range Monolithic Amplifier 50Ω PHA-1H+ 0.05 to 6 GHz The Big Deal • Ultra High IP3 • Broadband High Dynamic Range without external Matching Components • Operates to 105°C • May be used as a replacement to WJ AH1a,b SOT-89 PACKAGE Product Overview PHA-1H+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-1H+, unlike competitive models, has good input and output return loss over a broad frequency range without the need for external matching components and has demonstrated excellent reliability. It has repeatable performance from lot to lot and is enclosed in a SOT-89 package for very good thermal performance. Key Features Feature Broad Band: 0.05 to 6.0 GHz Extremely High IP3 Versus DC power Consumption 40.4 dBm typical at 2.4 GHz Advantages Broadband covering primary wireless communications bands: Cellular, PCS, LTE, WiMAX The PHA-1H+ matches industry leading IP3 performance relative to device size and power consumption. The combination of the design and E-PHEMT Structure provides enhanced linearity over a broad frequency range as evidence in the IP3 being typically 20 dB above the P 1dB point. This feature makes this amplifier ideal for use in: • Driver amplifiers for complex waveform up converter paths • Drivers in linearized transmit systems • Secondary amplifiers in ultra High Dynamic range receivers No External Matching Components Required Unlike competing products, Mini-Circuits PHA-1H+ provides Input and Output Return Loss of 10-23 dB up to 4 GHz without the need for any external matching components Low Noise Figure: 2.6dB typ. up to 4 GHz 3.4dB typ. up to 6 GHz A unique feature of the PHA-1H+ which separates this design from all competitors is the low noise figure performance in combination with the high dynamic range. Low Juction Temperature Tj=115°C at 85°C lead temperature and 135°C at 105°C lead temperature Results in excellent reliability. Notes: a. Suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses. b. The WJ AH1 part number is used for identification and comparison purposes only. Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 1 of 6 Ultra High Dynamic Range Monolithic Amplifier 0.05-6 GHz Product Features • High IP3, 40.4 dBm typ. at 2.4 GHz • Gain, 13.8 dB typ. at 2 GHz • High Pout, P1dB 22 dBm typ. at 2 GHz • Low noise figure, 2.2 dB @2 GHz • No external matching components required • May be used as replacement for WJ AH1a,b PHA-1H+ CASE STYLE: DF782 Typical Applications +RoHS Compliant The +Suffix identifies RoHS Compliance. See our web site for RoHS Compliance methodologies and qualifications • Base station infrastructure • Portable Wireless • CATV & DBS • MMDS & Wireless LAN • LTE General Description PHA-1H+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-1H+ has good input and output return loss over a broad frequency range without the need for external matching components. It has repeatable performance from lot to lot and is enclosed in a SOT-89 package for very good thermal performance. simplified schematic and pin description 3 RF-OUT & DC-IN RF-OUT and DC-IN RF-IN 2 GROUND 4 1 RF-IN GND Function Pin Number RF IN 1 RF input pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. RF-OUT and DC-IN 3 RF output and bias pin. DC voltage is present on this pin; therefore a DC blocking capacitor is necessary for proper operation. An RF choke is needed to feed DC bias without loss of RF signal due to the bias connection, as shown in “Recommended Application Circuit”, Fig. 2 GND 2,4 Description Connections to ground. Use via holes as shown in “Suggested Layout for PCB Design” to reduce ground path inductance for best performance. Notes: a. Suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses. b. The WJ AH1 part number is used for identification and comparison purposes only. Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com REV. A M176125 PHA-1H+ TH/RS/CP 190826 Page 2 of 6 PHA-1H+ Monolithic E-PHEMT MMIC Amplifier Electrical Specifications at 25°C, unless noted Parameter Condition (GHz) Frequency range Gain Min. 0.05 15.9 14.3 — — 9.8 — — 13.0 — — — — — 13.0 — — — — 0.05 0.8 2.0 3.0 4.0 6.0 0.05 0.8 2.0 3.0 4.0 6.0 0.05 0.8 2.0 3.0 4.0 6.0 2.0 0.05 0.8 2.0 3.0 4.0 6.0 0.05 0.8 2.0 3.0 4.0 6.0 0.5 1.0 2.0 3.0 4.0 6.0 Input return loss Output return loss Reverse isolation Output power @1 dB compression Output IP3 Noise figure 20.0 20.0 20.0 — — — — 38.0 — — — — Device operating voltage Device operating current Device current variation vs. temperature2 Device current variation vs voltage 4.8 — Thermal resistance, junction-to-ground lead at 88°C Vd=5.0V1 Typ. 17.7 15.9 13.8 12.1 10.9 9.6 11.9 18.2 12.5 10.8 10.3 8.1 14.2 22.9 19.7 17.1 15.5 13.7 19.6 22.1 21.8 22.6 22.2 22.5 22.0 39.6 40.6 40.4 40.8 41.4 41.0 1.7 1.8 2.2 2.4 2.6 3.4 5.0 132 101 0.057 Units Max. 6.0 19.5 17.5 — — 12.0 — — — — — — — — — — — — — — — — — — — — — — — — — GHz dB dB dB dB dBm dBm dB 5.2 165 36.1 V mA µA/°C mA/mV °C/W 1. Measured on Mini-Circuits characterization test board TB-313. See characterization test circuit (Fig. 1) 2. (Current at 85°C — ­ Current at -45°C)/130 Absolute Maximum Ratings3 Parameter Ratings Operating temperature (ground lead) -40°C to 105°C Storage temperature -65°C to 150°C Operating current at 5V 210 mA Power dissipation 1W Input power (CW) 24 dBm DC voltage on Pin 3 6V 3. Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are not intended for continuous normal operation. Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 3 of 6 PHA-1H+ Monolithic E-PHEMT MMIC Amplifier Histogram of OIP3 at 900 MHz 70 60 Number of Units 50 40 30 20 10 41.0 41.2 41.4 41.6 41.8 42.0 42.2 42.4 42.6 42.8 43.0 43.2 43.4 43.6 43.8 44.0 44.2 44.4 44.6 44.8 45.0 0 Output IP3 (dBm) Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 4 of 6 PHA-1H+ Monolithic E-PHEMT MMIC Amplifier Characterization Test Circuit Vcc (Supply voltage) 3 +5V 1 RF-IN 2,4 DUT BLK-18+ RF-OUT Bias-Tee ZX85-12G-S+ TB-313 Fig 1. Block Diagram of Test Circuit used for characterization. (DUT soldered on Mini-Circuits Characterization test board TB-313 Gain, Return loss, Output power at 1dB compression (P1 dB) , output IP3 (OIP3) and noise figure measured using Agilent’s N5242A PNA-X microwave network analyzer. Conditions: 1. Gain and Return loss: Pin= -25dBm 2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 5 dBm/tone at output. Recommended Application Circuit Vcc Cbypass Cblock IN 4 Ibias 3 RFC Vd 1 2 OUT Cblock Fig 2. Test Board includes case, connectors, and components soldered to PCB Product Marking PH1H Marking may contain other features or characters for internal lot control Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp Mini-Circuits ® www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 5 of 6 PHA-1H+ Monolithic E-PHEMT MMIC Amplifier Additional Detailed Technical Information additional information is available on our dash board. To access this information click here Data Table Performance Data Swept Graphs S-Parameter (S2P Files) Data Set (.zip file) DF782 (SOT 89) Plastic package, exposed paddle Case Style lead finish: Matte-Tin Tape & Reel F55 Standard quantities available on reel 7” reels with 20, 50, 100, 200, 500 or 1K devices Suggested Layout for PCB Design PL-313 Evaluation Board TB-545-1H+ Environmental Ratings ENV08T8 ESD Rating Human Body Model (HBM): Class 1B (500 to