PHA-23LN+

ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier 50Ω PHA-23LN+ 30MHz to 2GHz THE BIG DEAL y Ultra-High IP3, +37.4 dBm typ. y Low supply voltage, 3 to 5V y Excellent Noise Figure, 1.2 dB typ. Generic photo used for illustration purposes only APPLICATIONS y Base station infrastructure y CATV y Cellular CASE STYLE: DF782 PRODUCT OVERVIEW PHA-23LN+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PHA-23LN+ has good input and output return loss over a broad frequency range. PHA-23LN+ is enclosed in a SOT-89 package and has very good thermal performance. KEY FEATURES Feature Broad Band: 30MHz to 2GHz Extremely High IP3 40.9 dBm typical at 30MHz 37.4 dBm typical at1GHz Advantages Broadband covering primary wireless communications bands: VHF, UHF, Cellular The PHA-23LN+ matches industry leading IP3 performance relative to device size and power consumption. The combination of the design and E-PHEMT Structure provides enhanced linearity over a broad frequency range as evidence in the IP3 being approximately 13-18 dB above the P1dB point. This feature makes this amplifier ideal for use in: y Driver amplifiers for complex waveform up converter paths y Drivers in linearized transmit systems y Secondary amplifiers in ultra-High Dynamic range receivers Low Noise Figure 1.2 dB at 1 GHz Enables lower system noise figure performance and along with High OIP3 provides high dynamic range Low Supply Voltage PHA-23LN+ supports low supply voltage operation which indicate low power consumption. REV. B ECO-010399 PHA-23LN+ MCL NY 221221 www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 1 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-23LN+ ELECTRICAL SPECIFICATIONS1 AT 25°C, 50Ω, UNLESS NOTED OTHERWISE Parameter Condition (MHz) Frequency Range Input Return Loss Output Return Loss Reverse isolation Output Power @1 dB compression Output IP3 2 Noise Figure Typ. 30 30 Gain Vd=5V1 Min. — 23.0 Typ. 2000 30-2000 — 22.3 500 — 21.9 — 21.0 1000 18.9 21.0 23.1 19.7 1500 18.1 20.1 22.1 18.5 2000 — 18.9 — 17.0 30 12.0 12.4 500 11.6 10.5 1000 9.4 7.5 1500 9.6 7.7 2000 8.9 6.9 30 14.9 16.6 500 16.5 21.0 1000 18.8 18.0 1500 12.2 10.8 2000 9.4 8.5 1000 27.2 26.9 30 22.8 17.4 500 24.1 19.0 1000 23.9 18.8 1500 23.4 18.4 2000 23.3 18.0 30 40.9 34.7 500 39.3 33.3 1000 37.4 30.9 1500 36.3 30.5 2000 35.6 29.7 30 1.1 1.1 500 1.0 1.0 1000 1.2 1.2 1500 1.3 1.3 2000 1.6 1.6 Device Operating Voltage 5.0 Device Operating Current 141.7 Device Current Variation vs. Temperature3 Device Current Variation vs Voltage Vd=3V1 Max. 162 Units MHz dB dB dB dB dBm dBm dB 3.0 V 72.4 mA 14.2 33.1 µA/°C 0.0354 0.0354 mA/mV 23.3 23.3 °C/W Thermal Resistance, Junction-to-ground lead at 85°C stage temperature 1. Measured on Mini-Circuits Characterization test board TB-951-23LN+. See Characterization Test Circuit (Fig. 1) 2. Tested at Pout= 0 dBm / tone. 3. (Current at 85°C — Current at -45°C)/130 www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 2 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-23LN+ MAXIMUM RATINGS4 Parameter Ratings Operating Temperature (ground lead) -40°C to 105°C Storage Temperature -65°C to 150°C Power Dissipation5 3.3W +22 dBm (5 minutes max)6 +4 dBm (continuous) for 0.03-1GHz at 3V +8 dBm (continuous) for 0.03-1GHz at 5V +12 dBm (continuous) for 1-2GHz at 3V +15 dBm (continuous) for 1-2GHz at 5V Input Power (CW) DC Voltage on Pin 3 10V 4. Permanent damage may occur if any of these limits are exceeded. Electrical maximum ratings are not intended for continuous normal operation. 5. Up to 85°C, derate linearly to 2.5W at 105°C. 6. Up to 85°C, derate linearly to +19dBm at 105°C. SIMPLIFIED SCHEMATIC AND PIN DESCRIPTION 3 RF-OUT & DC-IN RF-OUT and DC-IN RF-IN 4 2 GROUND 1 RF-IN GND Function Pin Number Description RF IN 1 RF Input RF-OUT and DC-IN 3 RF Output and DC Bias GND 2,4 Connections to ground. www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 3 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-23LN+ CHARACTERIZATION TEST / RECOMMENDED APPLICATION CIRCUIT Vdd C6 C5 4 L2 C2 RF-IN 1 DUT 0402 0805 0402 Value 1.2pF 0.1uF 0.001uF 0.01uF 1.21KOhm 0.68uH 1nH RF-OUT 2 C3 Size L1 C4 C1 Component C1 C2,C3,C6 C4 C5 R1 L1 L2 3 Manufacturer Murata KOA Coilcraft R1 P/N GRM1555C1H1R2WA01D GRM155R71C104KA88D GRM1555C1H102JA01D GRM155R71E103KA01D RK73H1ETTP1211F 0805LS-681XJLB 0402CS-1N0XJLW Fig 1. Block Diagram of Test Circuit used for characterization. (DUT soldered on Mini-Circuits Characterization test board TB-951-23LN+) Gain, Return loss, Output power at 1dB compression (P1 dB), output IP3 (OIP3) and noise figure measured using Agilent’s N5242A PNA-X microwave network analyzer. Conditions: 1. Gain and Return loss: Pin= -25dBm 2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 0 dBm/ tone at output. PRODUCT MARKING PH23 model family designation Marking may contain other features or characters for internal lot control www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 4 OF 5 ULTRA HIGH DYNAMIC RANGE Monolithic Amplifier PHA-23LN+ ADDITIONAL DETAILED TECHNICAL INFORMATION IS AVAILABLE ON OUR DASH BOARD. TO ACCESS C LIC K HERE Data Table Performance Data Swept Graphs S-Parameter (S2P Files) Data Set (.zip file) Case Style DF782 (SOT 89) Plastic package, exposed paddle lead finish: matte-tin Tape & Reel Standard quantities available on reel F55 7” reels with 20, 50, 100, 200, 500 or 1K devices Suggested Layout for PCB Design PL-512 Evaluation Board TB-951-23LN+ Environmental Ratings ENV08T9 ESD RATING Human Body Model (HBM): Class 1B (Pass 500 V) in accordance with ANSI/ESD STM 5.1 - 2001 MSL RATING Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D MSL TEST FLOW CHART Start Visual Inspection Electrical Test SAM Analysis Reflow 3 cycles 260°C Soak 85°C/85RH 168 hours Bake at 125°C, 24 hours Visual Inspection Electrical Test SAM Analysis Finish NOTES A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the standard. Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com PAGE 5 OF 5