ML6102X262XX

厂商：
MINILOGIC
封装：
描述：
ML6102X262XX - Positive Voltage Detector (Inverted Output) - Minilogic Device Corporation Limited

数据手册：

下载ML6102X262XX.pdf

立即购买

详情介绍
数据手册
价格&库存

ML6102X262XX 数据手册

ML6102 ML6102 Series Positive Voltage Detector (Inverted Output) Application Memory Battery Back-up Circuits Power Failure Detection Power-on Reset Circuit System Battery Life and Charge Voltage Monitor Features CMOS Low Power Consumption : Typical 1.0uAat Vin=2.0V Selectable Detect V oltage : 1.1V to 6.0V in 0.1V increments HighlyAccurate : Detect V oltage 1.1V to 1.9V + 3% Detect V oltage 2.0V to 6.0V + 2% Operating V oltage : 0.8V to 10.0V PackageAvailable : SOT23 (150mW), SOT89 (500mW) & TO92 (300mW) General Description The ML6102 is a group of high-precision and low-power voltage detectors. The ML6102 consists of a highly-accurate and low-power reference voltage source, a comparator, a hysteresis circuit, and an output driver. Detect voltage is very accurate and stable with N-channel open drain and CMOS, are available. Output Voltage is in inverted sense compared with ML61 series voltage detector. Block Diagram (1) CMOS Output (2) N-Channel Open Drain Output Absolute Maximum Ratings Parameter Input Voltage Output Current Output Voltage Continuous SOT-23 Total Power SOT-89 Dissipation TO-92 Operating Ambient Temperature Storage Temperature Symbol VIN IOUT VOUT Pd Ratings 10 50 VSS-0.3 ~VIN+0.3 150 500 300 Topr Tstg P1/11 -40 ~ +70 -40 ~ +70 o o Units V mA V mW C C Preliminary, June 2005 ML6102 Electrical Characteristics Parameter Detect Voltage Hysteresis Range Symbol VDF VHYS Conditions VDF = 1.1V to 1.9V VDF = 2.0V to 7.0V VDF = 1.1V to 2.9V VDF = 3.0V to 7.0V VIN = 1.0V VIN = 2.0V VIN = 3.0V VIN = 4.0V VIN = 5.0V VDF = 1.1~7.0V Nch VDS = 0.5V VIN = 1.0V VIN = 2.0V VIN = 3.0V VIN = 4.0V VIN = 5.0V Pch VDS = 1.0V VIN = 5.0V (CMOS Output) While VIN changes from 0.6V to 10V Min Typ VDF X0.97 VDF X0.98 X0.04 VDF X0.05 X0.015 VDF X0.025 0.8 1.0 1.3 1.6 2.0 0.8 1.0 3.0 5.0 11.0 13.0 -5.0 0.2 ms Max Units X1.03 V X1.02 V X0.06 V X0.035 V 2.0 2.5 uA 3.0 3.5 4.0 10.0 V Supply Current ISS Operating Voltage VIN Output Current IOUT mA Transient Delay Time (VDR -> VOUT Inversion) tDLY P2/11 Preliminary, June 2005 ML6102 Electrical Characteristics By Detector Threshold Part Number ML6102X113XX ML6102X123XX ML6102X133XX ML6102X143XX ML6102X153XX ML6102X163XX ML6102X173XX ML6102X183XX ML6102X193XX ML6102X202XX ML6102X212XX ML6102X222XX ML6102X232XX ML6102X242XX ML6102X252XX ML6102X262XX ML6102X272XX ML6102X282XX ML6102X292XX ML6102X302XX ML6102X312XX ML6102X322XX ML6102X332XX ML6102X342XX ML6102X352XX ML6102X362XX ML6102X372XX ML6102X382XX ML6102X392XX ML6102X402XX ML6102X412XX ML6102X422XX ML6102X432XX ML6102X442XX ML6102X452XX ML6102X462XX ML6102X472XX ML6102X482XX ML6102X492XX ML6102X502XX ML6102X512XX ML6102X522XX ML6102X532XX ML6102X542XX ML6102X552XX ML6102X562XX ML6102X572XX ML6102X582XX ML6102X592XX ML6102X602XX Standard Detector Accuracy Detector Threshold VDF (V) MIN. 1.067 1.164 1.261 1.358 1.455 1.552 1.649 1.746 1.843 1.960 2.058 2.156 2.254 2.352 2.450 2.548 2.646 2.744 2.842 2.940 3.038 3.136 3.234 3.332 3.430 3.528 3.626 3.724 3.822 3.920 4.018 4.116 4.214 4.312 4.410 4.508 4.606 4.704 4.802 4.900 4.998 5.096 5.194 5.292 5.390 5.488 5.586 5.684 5.782 5.880 TYP. 1.100 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000 2.100 2.200 2.300 2.400 2.500 2.600 2.700 2.800 2.900 3.000 3.100 3.200 3.300 3.400 3.500 3.600 3.700 3.800 3.900 4.000 4.100 4.200 4.300 4.400 4.500 4.600 4.700 4.800 4.900 5.000 5.100 5.200 5.300 5.400 5.500 5.600 5.700 5.800 5.900 6.000 MAX. 1.133 1.236 1.339 1.442 1.545 1.648 1.751 1.854 1.957 2.040 2.142 2.244 2.346 2.448 2.550 2.652 2.754 2.856 2.958 3.060 3.162 3.264 3.366 3.468 3.570 3.672 3.774 3.876 3.978 4.080 4.182 4.284 4.386 4.488 4.590 4.692 4.794 4.896 4.998 5.100 5.202 5.304 5.406 5.508 5.610 5.712 5.814 5.916 6.018 6.120 Hysteresis Range VHYS (V) MIN. MAX. Condition Supply Current ISS (uA) TYP. MAX. 3% VIN = 1.0V 0.8 2.0 VDF x 0.04 VDF x 0.06 VIN = 2.0V 1.0 2.5 VIN = 3.0V 1.3 3.0 2% VDF x 0.015 VDF x 0.035 VIN = 4.0V 1.6 3.5 VIN = 5.0V 2.0 4.0 P3/11 Preliminary, June 2005 ML6102 Part Number ML6102X113XX ML6102X123XX ML6102X133XX ML6102X143XX ML6102X153XX ML6102X163XX ML6102X173XX ML6102X183XX ML6102X193XX ML6102X202XX ML6102X212XX ML6102X222XX ML6102X232XX ML6102X242XX ML6102X252XX ML6102X262XX ML6102X272XX ML6102X282XX ML6102X292XX ML6102X302XX ML6102X312XX ML6102X322XX ML6102X332XX ML6102X342XX ML6102X352XX ML6102X362XX ML6102X372XX ML6102X382XX ML6102X392XX ML6102X402XX ML6102X412XX ML6102X422XX ML6102X432XX ML6102X442XX ML6102X452XX ML6102X462XX ML6102X472XX ML6102X482XX ML6102X492XX ML6102X502XX ML6102X512XX ML6102X522XX ML6102X532XX ML6102X542XX ML6102X552XX ML6102X562XX ML6102X572XX ML6102X582XX ML6102X592XX ML6102X602XX Operating Voltage VIN (V) MIN. MAX. Pch Output Current Pch IOUT (mA) Condition TYP. Nch Output Current Nch IOUT (mA) Condition TYP. Transient Delay Time tDLY (ms) MAX. VDS = 0.5V VIN = 1.0V 1.0 VDS = 0.5V VIN = 2.0V 3.0 VDS = 1.0V 0.8V 10V VIN = 5.0V -5.0 VDS = 0.5V VIN = 3.0V 5.0 0.2 VDS = 0.5V VIN = 4.0V 11.0 VDS = 0.5V VIN = 5.0V 13.0 P4/11 Preliminary, June 2005 ML6102 Pin Configuration SOT-23-3 SOT-89-3 TO-92 Package Pin Number SOT-23-3 SOT-89-3 TO-92 1 1 1 3 2 2 2 3 3 Pin Name VOUT VIN VSS Function Supply Voltage Output Supply Voltage Input Ground P5/11 Preliminary, June 2005 ML6102 Functional Description (Refers to CMOS Output) Input Voltage (VIN ) Detect Release Voltage (VDR ) Detect Voltage (V DF ) Minimum Operating Voltage (VMIN ) Ground Voltage (VSS ) Output Voltage (VOUT ) tOL tOH tOL t OH Ground Voltage (VSS ) Notes : 1. Output cannot be specified for power supply voltage under VMIN (ie. 0.8V) because operation is not guaranteed for that range. 2. VDF : Detect Voltage for drop in power supply voltage 3. VDR : Detect Release Voltage for rise in power supply voltage 4. VHYS = VDR – VDF 5. tOL : Time lag between the time that the power supply voltage rises to the detect release voltage (VDR) and the time that the output pin (OUT) goes to “L” level. 6. tOH : Time lag between the time that the power supply voltage falls to the detect voltage (VDF) and the time that the output pin (OUT) goes to “H” level. 7. These characteristics for the N-channel open drain output are when a load resistor is connected between the OUT and IN pins. P6/11 Preliminary, June 2005 ML6102 Ordering Information Designator a Description Output Configuration C = CMOS Output N = N-Channel Output Detect Voltage eg. 30=3.0V 50=5.0V Detect Voltage Accuracy 2 = +2.0% 3 = +3.0% Package Type M = SOT-23-3 P = SOT-89 T = TO-92 b c d e Device Orientation R = Embossed Tape (Orientation of Device : Right) L = Embossed Tape (Orientation of Device : Left) B = Bag (TO-92) H = Paper Tape (TO-92) G = Lead Free Part G Marking SOT-23-3 : Designator 1 Description Type D = Voltage Detector (CMOS Output) E = Voltage Detector (N-channel Output) Output Voltage eg. 30 = 3.0V Internal Code 2,3 4 SOT-89-3 : Designator 1 Description Type D = Voltage Detector (CMOS Output) E = Voltage Detector (N-channel Output) Output Voltage eg. 30 = 3.0V Internal Code 2,3 4 TO-92 : Designator 1 Description Type D = Voltage Detector (CMOS Output) E = Voltage Detector (N-channel Output) Output Voltage eg. 30 = 3.0V Internal code Year Code eg. 05 = Year 2005 Week Code eg. 30 = Week 30 2,3 4 5, 6 7, 8 P7/11 Preliminary, June 2005 ML6102 Packaging Information (0.8) SOT-89-3 : 0.15 -0.1 -0.05 4.5 ± 0.1 1.5 ± 0.1 SOT-23-3 -0.1 0.4 -0.05 1.72 ± 0.1 2.45 ± 0.15 0 ~ 0.1 2.8 ± 0.2 1.6 +1.2 -0.0.1 (0.95) min. 0.2 0.42 ± 0.06 0.42 ± 0.06 0.49 ± 0.06 1.1 mm 4.25 max 0.4 ± 0.04 1.9 ± 0.2 2.9 ± 0.2 1.1 ± 0.1 1.5 ± 0.1 1.5 ± 0.1 1.27 1.27 ∅5.2 max 4.2 max TO-92 : Units : mm 5.3 max Recommended Pattern Layout SOT-23-3 : 2.4 12.7 min SOT-89-3 : 0.9 2.2 45º 45º 1.9 1.0 1.5 0.8 1. 0 1.0 P8/11 1.6 Preliminary, June 2005 3.7 ML6102 Tape and Reel Information SOT-23 : SIZE (mm) A B C D G H ∅ 178 ± 0.8 2 ± 0.2 ∅ 13 ± 0.2 ∅ 21 ± 0.8 8 ± 0.5 ∅ 60 3,000 pcs / reel SOT-23 Taping Specifications : 4 ± 0.1 2 ± 0.05 ∅1.5 + 0.1 -0 3.5 ± 0.05 1.75 ± 0.1 4 ± 0.1 ∅ 1.1 ± 0.1 Direction of feed 8 ± 0.2 Direction of feed “R” type [Orientation of Device: Right] Standard Type “L” type [Orientation of Device: Left] Reverse Type P9/11 Preliminary, June 2005 ML6102 SOT-89 : SIZE (mm) A B C D G H ∅ 178 ± 0.8 2 ± 0.2 ∅ 13 ± 0.2 ∅ 21 ± 0.8 12 ± 0.5 ∅ 60 1,000 pcs / reel SOT-89 Taping Specifications : 4.0 ± 0.1 2.0 ± 0.05 ∅ 1.5 + 0.1 0 5.65 ± 0.05 1.5 ± 0.1 8.0 ± 0.1 Direction of feed 12.0 ± 0.2 Direction of feed “R” type [Orientation of Device: Right] Standard Type “L” type [Orientation of Device: Left] Reverse Type P10/11 Preliminary, June 2005 ML6102 TO-92 Taping Specifications : P H1 H L1 H0 WO W2 W1 W P2 F PO D t SIZE (mm) P PO P2 F W WO W1 W2 H H0 H1 D t L1 12.7 ± 1.0 12.7 ± 0.3 6.35 ± 0.4 2.5+ 0.45 - 0.15 2,000 pcs / box 18.0 ± 1.0 6.0 ± 0.3 9.0 ± 0.5 0.5 MAX 19.0 ± 0.5 16.0 ± 0.5 32.25 MAX ∅ 4.0 ± 0.2 0.6 ± 0.2 3.5 MIN The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. P11/11 Preliminary, June 2005

下载 PDF

ML6102X262XX

物料型号： - ML6102系列，包括多种型号，如ML6102X113XX、ML6102X123XX等，具体型号根据检测电压的不同而有所区别。

器件简介： - ML6102是一款高精度、低功耗的电压检测器。它由一个高精度和低功耗的参考电压源、一个比较器、一个滞后电路和一个输出驱动器组成。检测电压非常准确和稳定，提供N沟道开漏和CMOS输出版本，输出电压与ML61系列电压检测器相比是反向的。

引脚分配： - SOT-23-3封装：1脚为VOUT（供电电压输出），2脚为VSS（地），3脚为VIN（供电电压输入）。 - SOT-89-3封装：1脚为VOUT，2脚为VIN，3脚为VSS。 - TO-92封装：1脚为VOUT，2脚为VIN，3脚为VSS。

参数特性： - 工作电压范围：0.8V至10.0V。 - 功耗：典型值为1.0μA（在2.0V供电下）。 - 检测电压精度：1.1V至1.9V为±3%，2.0V至6.0V为±2%。 - 滞后范围：根据检测电压不同，滞后范围在0.04V至0.06V之间。

功能详解： - ML6102用于检测电源电压，并在电压下降到设定的检测电压时提供输出。它适用于电池后备电路、电源失效检测、上电复位电路等应用。

应用信息： - 适用于存储器电池后备电路、电源失效检测、系统电池寿命和充电电压监测等。

封装信息： - 提供SOT23（150mW）、SOT89（500mW）和TO92（300mW）三种封装形式。每种封装都有详细的布局图和胶带规格。

ML6102X262XX 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“ML6102X262XX”相匹配的价格&库存，您可以联系我们找货