ML6206P502PHGG

ML6206 ML6206 Series Low ESR Cap. Compatible Positive Voltage Regulator Application Battery Powered Equipment Palmtops Portable Cameras and Video Recorders Reference Voltage Sources Features CMOS Low Power Consumption : Typical 1.0uAat V out=3.0V Output V oltage Range : 1.5V to 5.0V in 0.1V increments HighlyAccurate: Output V oltage + 3% for 1.5V to 1.9V Output V oltage + 2% for 2.0V to 5.0V Maximum Output Current: 250mA (within the maximum power dissipation, V out=5.0V) Small Input-Output V oltage Differential: 0.16V at 100mAand 0.4V at 200mA Input stability: Typ. 0.2%/V PackageAvailable: SOT- 23 (150mW), SOT- 89 (500mW) & TO - 92 (300mW) Reverse Battery Protection Current Limit General Description The ML6206 series are highly precise, low power consumption, high voltage, positive voltage output, three-pin regulator. It provides high output current even when the input/output voltage differential is small. The ML6206 consists of a high-precision voltage reference, an error correction circuit, a current limited output driver and reverse battery protection. Block Diagram Absolute Maximum Ratings Parameter Input Voltage Output Current Output Voltage SOT-23 Continuous TO-92 Operating Ambient Temperature Storage Temperature Total Power Dissipation SOT-89 Symbol VIN IOUT VOUT Pd Topr Tstg P1/13 Ratings 6.5 500 VSS-0.3 ~VIN+0.3 150 500 300 -40 ~ +70 -40 ~ +70 Units V mA V mW o o C C July 2008 ML6206 Pin Configuration SOT-23 SOT-89 TO-92 Package Pin Number SOT23 SOT89 TO-92 1 1 1 3 2 2 2 3 3 Pin Name VSS VIN VOUT Function Ground Power Input Output Standard Circuit Note on Use 1. Oscillation may occur as a result of the impedance present between the power supply and the IC’s input. Please use a capacitor (CIN) of at least 1uF, when the impedance is 10 ohm or more. With a large output current, Voltage output can be stabilised by increasing capacitor (CIN) size. If CIN is small and capacitor (CL) size is increased, oscillation may occur. In such cases, Voltage output can be stabilised by either increasing the size of CIN or decreasing the size of CL. 2. Please ensure that output current (IOUT) is less than Pd / (VIN-VOUT) and does not exceed the stipulated Continuous Total Power Dissipation value (Pd). Test Circuit Test Circuit 1 Test Circuit 2 P2/13 July 2008 ML6206 Electrical Characteristic ML6206P153 VOUT(T)=1.5V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Current Limiter Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Ishort Conditions IOUT=30mA VIN=2.5V VIN=2.5V, VOUT(E) ≥1.35V VIN=2.5V, 1mA≤IOUT≤100mA IOUT=100mA IOUT=200mA VIN=2.5V IOUT=30mA VOUT(T)+1.0V≤VIN≤6V VIN = VOUT+1.5V, VOUT=VSS Min 1.455 200 35 250 500 1.0 0.01 1.2 100 0.30 6.5 Typ 1.500 Max 1.545 Units V mA mV mV mV uA %V V mA Circuit 1 1 1 1 1 2 1 1 ML6206P302 VOUT(T)=3.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Current Limiter Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Ishort Conditions IOUT=30mA VIN=4.0V VIN=4.0V, VOUT(E) ≥2.7V VIN=4.0V, 1mA≤IOUT≤100mA IOUT=100mA IOUT=200mA VIN=4.0V IOUT=30mA VOUT(T)+1.0V≤VIN≤6V VIN = VOUT+1.5V, VOUT=VSS Min 2.940 270 25 120 260 1.0 0.01 1.2 100 0.30 6.5 Typ 3.000 Max 3.060 Units V mA mV mV mV uA %V V mA Circuit 1 1 1 1 1 2 1 1 ML6206P332 VOUT(T)=3.3V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Current Limiter Symbol VOUT(E) (Note 2) IOUT max ∆VOUT Vdif1 Vdif2 ISS ∆VOUT ∆VIN * VOUT VIN Ishort Conditions IOUT=30mA VIN=4.3V VIN=4.3V, VOUT(E) ≥2.97V VIN=4.3V, 1mA≤IOUT≤100mA IOUT=100mA IOUT=200mA VIN=4.3V IOUT=30mA VOUT(T)+1.0V≤VIN≤6V VIN = VOUT+1.5V, VOUT=VSS Min 2.234 270 25 120 260 1.0 0.01 1.2 100 0.30 6.5 Typ 3.300 Max 3.366 Units V mA mV mV mV uA %V V mA Circuit 1 1 1 1 1 2 1 1 Note : 1. VOUT(T) = Specified Output Voltage. 2. VOUT(E) = Effective Output Voltage (i.e. the output voltage when (VOUT(T)+1.0V) is provided at the VIN pin while maintaining a certain IOUT value). 3. Vdif = VIN1(Note 4) – VOUT(E) 4. VIN1 = The input voltage at the time 98% of VOUT (E) is output (input voltage has been gradually reduced). P3/13 July 2008 ML6206 Typical Performance Characteristics 1) Output Voltage vs. Output Current ML6206P153 ML6206P302 2) Current Limit ML6206P153 ML6206P302 ML6206P502 P4/13 July 2008 ML6206 3) Output Voltage vs. Input Voltage ML6206P153 ML6206P302 4) Supply Current vs. Input Voltage ML6206P153 ML6206P302 5) Output Voltage vs. Ambient Temperature ML6206P153 ML6206P302 P5/13 July 2008 ML6206 6) Supply Current vs. Ambient Temperature ML6206P153 ML6206P302 7) Input Transient Response 1 ML6206P153 P6/13 July 2008 ML6206 ML6206P302 8) Input Transient Response 2 ML6206P153 ML6206P302 P7/13 July 2008 ML6206 9) Load Transient Response ML6206P153 ML6206P302 P8/13 July 2008 ML6206 10) Power Supply Rejection Ratio ML6206P153 ML6206P302 ML6206P302 Ordering Information Designator ①② ③ Description Output Voltage eg. 30=3.0V 50=5.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Package Type M = SOT-23 P = SOT-89 T = TO-92 Device Orientation R = Embossed Tape (Orientation of Device : Right) L = Embossed Tape (Orientation of Device : Left) B = Bag (TO-92) H = Paper Tape (TO-92) G = ROHS Part GG = Green Part ML6206P①②③④⑤⑥ ④ ⑤ ⑥ P9/13 July 2008 ML6206 Packaging Information SOT-23 : (0.8) 4.5 ± 0.1 SOT-89 : 1.5 ± 0.1 0.15 -0.1 -0.1 -0.05 0.4 -0.05 1.72 ± 0.1 2.45 ± 0.15 0 ~ 0.1 2.8 ± 0.2 1.6 +1.2 -0.0.1 (0.95) min. 0.2 0.42 ± 0.06 0.42 ± 0.06 0.49 ± 0.06 1.1 mm 4.25 max 0.4 ± 0.04 1.9 ± 0.2 2.9 ± 0.2 1.1 ± 0.1 1.5 ± 0.1 1.5 ± 0.1 TO-92 : 1.27 1.27 ∅5.2 max 5.3 max 4.2 max Units : mm 12.7 min Recommended Pattern Layout 2.2 SOT-23 : 2.4 SOT-89 0.9 45º 45º 1.9 0.8 1.0 1. 0 1.6 1.0 P10/13 1.5 3.7 July 2008 ML6206 Tape and Reel Information SOT-23 : SIZE (mm) A B C D G H ∅ 178 ± 0.8 2 ± 0.2 ∅ 13 ± 0.2 ∅ 21 ± 0.8 8 ± 0.5 ∅ 60 3,000 pcs / reel SOT-23 Taping Specifications : 4 ± 0.1 2 ± 0.05 ∅1.5 + 0 .1 -0 3.5 ± 0.05 1.75 ± 0.1 4 ± 0.1 ∅ 1.1 ± 0.1 Direction of feed 8 ± 0.2 Direction of feed “R” type [Orientation of Device: Right] Standard Type “L” type [Orientation of Device: Left] Reverse Type P11/13 July 2008 ML6206 SOT-89 : SIZE (mm) A B C D G H ∅ 178 ± 0.8 2 ± 0.2 ∅ 13 ± 0.2 ∅ 21 ± 0.8 12 ± 0.5 ∅ 60 SOT-89 Taping Specifications : 4.0 ± 0.1 2.0 ± 0.05 ∅ 1.5 + 0.1 0 1,000 pcs / reel 5.65 ± 0.05 1.5 ± 0.1 8.0 ± 0.1 Direction of feed 12.0 ± 0.2 Direction of feed “R” type [Orientation of Device: Right] Standard Type “L” type [Orientation of Device: Left] Reverse Type P12/13 July 2008 ML6206 TO-92 Taping Specifications : P H1 H L1 H0 WO W2 W1 W P2 F PO t D P PO P2 F W WO W1 W2 H H0 H1 D t L1 SIZE (mm) 12.7 ± 1.0 12.7 ± 0.3 6.35 ± 0.4 2.5 -0.15 +0.45 2,000 pcs / box 18.0 ± 1.0 6.0 ± 0.3 9.0 ± 0.5 0.5 MAX 19.0 ± 0.5 16.0 ± 0.5 32.25 MAX ∅ 4.0 ± 0.2 0.6 ± 0.2 3.5 MIN MiniLogic reserves the rights to change the information and specification s without prior notice. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. P13/13 July 2008