AGF-10S12

AGF-10 Series 10 Watts Universal Input Range AC/DC Power Modules Single Outputs Key Features High Efficiency up to 76% 90~264VAC, 47~440Hz Universal Input Range Single Output Modules I/O Isolation 3000VAC EMI Complies With EN55022 Class B and FCC part 15, level B EMC Complies With EN61000 MTBF > 300,000 Hours Meets IEC / EN / UL 60950-1 Safety Standards Meets IEC61140 Safety Class II Operating Temperature 71] (Reference to Derating Curve) ~ 90 264 VAC Universal Voltage 3000 VAC I/O Isolation OVP Protection EMI EN55022 EMC EN61000 AGF-10 is a 10 Watts series of AC-DC power modules. These modules have wide input range of 90~264VAC and are available in output voltages of 3.3V, 5V, 12V, 15V and 24V with efficeincy as high as 76% . Other features include continuous short circuit protection, overvoltage protection, output current limitation, EMC meets EN61000-4(-2,-3,-4), EMI meets EN55022 level B conducted noise compliance minimize design-in time, cost and eliminate the need for external components. The AGF-10 meets IEC / EN / UL 60950-1 safety approval qualifies this product for worldwide markets. The series is a wide variety of applications in commercial and industrial electronic equipment, and MTBF is up to 300,000 hours. Environmental Specifications Parameter Operating Temperature Storage Temperature Humidity Cooling Conducted EMI Conducted EMC Conditions Ambient Min. -25 -40 --Free-Air Convection EN55022 Class B EN6100-4-2 EN6100-4-3 EN6100-4-4 Max. +71 +85 +95 Unit ] ] % 1 MINMAX REV:5 2009/02/16 AGF-10 Series Model Selection Guide Model Number Output Voltage Output Current Max. mA 2500 2000 833 667 417 Min. mA 250 200 83 67 42 Input Current 115VAC, 60Hz @Max. Load @No Load mA (Typ.) mA (Typ.) 171 15 201 15 191 15 193 15 201 15 Capacitive Load Max. uF 2200 2200 1000 1000 680 Efficiency @Max. Load % (Typ.) 70 72 76 75 72 AGF-10S03 AGF-10S05 AGF-10S12 AGF-10S15 AGF-10S24 VDC 3.3 5 12 15 24 Input Fuse Selection Guide All Models External Fuse (Recommended) 1.5A Slow - Blow Type Input Specifications Parameter Input Voltage Range Input Frequency Range Inrush Current (Cold Start at 25]) Model All Models 115VAC 230VAC Min. 90 47 ----Typ. --------Max. 264 440 15 30 Unit VAC Hz A A Output Specifications Parameter Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20MHz) Over Voltage Protection Temperature Coefficient Overshoot Current limitation Short circuit protection 85VAC, Hiccup technique, auto-recovery Vin=Min. to Max. Io=Min. to Max. 3.3 & 5.0VDC Output Models Other Output Models Zener diode clamp Conditions Min. ----------------105 Typ. {1.0 {0.5 {0.5 1.5 0.8 120 {0.01 ----Max. {2.0 {1.0 {1.0 1.8 1.0 --{0.02 5 --Unit % % % %Vpp of Vo %Vpp of Vo % of Vo %/] % % Hiccup mode, indefinite (automatic recovery) General Specifications Parameter Isolation Voltage Rated Isolation Voltage Test Isolation Resistance Switching Frequency Hold-up Time MTBF 115VAC, 60Hz MIL-HDBK-217F @ 25], Ground Benign Conditions Input to Output, 60 Seconds Input to output, Flash Tested for 1 Second 500VDC Min. 3000 4700 100 ----330 Typ. ------125 15 --Max. ------------Unit VAC VDC M[ KHz ms K Hours REV:5 2009/02/16 MINMAX 2 AGF-10 Series Note : 1. Specifications typical at Ta=+25], resistive load, 115VAC, 60Hz input voltage, rated output current unless otherwise noted. 2. Ripple & Noise measurement bandwidth is 0-20 MHz. 3. These power modules require a minimum output loading to maintain specified regulation. 4. Operation under no-load conditions will not damage these devices; however they may not meet all listed specifications. 5. All AC/DC modules should be externally fused at the front end for protection. 6. Other input and output voltage may be available, please contact factory. 7. Specifications subject to change without notice. Block Diagram L EMI Filter and Inrush Current Limiter Rectifier Switching Device Rectifier OVP +Vo N Fuse -Vo Control Circuit Isolation Ref.Amp Derating Curve 100 80 Output Power (%) 60 40 25% 20 0 -25 ～ 10 20 30 40 50 60 70 Ambient Temperature ] 3 MINMAX REV:5 2009/02/16 AGF-10 Series Mechanical Dimensions Physical Characteristics Case Size 23.5 [0.93] 10.0 [0.39] 0.7 [0.03] : 52.4*27.2*23.5 mm 2.06*1.07*0.93 inches Plastic resin + Fiberglass 54g UL94V-0 10.16 [0.40] 10.16 [0.40] Case Material Weight Flammability : : : 45.72 [1.80] 52.4 [2.06] 1.0 [0.04] 5 4 3 Bottom Side 2 1 20.32 [0.80] 27.2 [1.07] Tolerance Millimeters X.X{0.5 X.XX{0.25 5.0 [0.20] Inches X.XX{0.02 X.XXX{0.01 {0.04 Pin {0.1 Pin Connections Pin 1 2 3 4 5 Function AC(N) - AC Neutral AC(L) - AC Line +Vout -Vout No Pin REV:5 2009/02/16 MINMAX 4