MSLU129

MSLU100 Series 1W, Miniature SMD, Single & Dual Output DC/DC Converters Key Features Efficiency up to 80% 1500VDC Isolation MTBF > 2,000,000 Hours Low Cost Input 5,12 and 24VDC Output 3.3, 5, 12,15,9,{5,{12and {15VDC Temperature Performance -25] to +75] UL 94V-0 Package Material Interanl SMD Construction $ Low Profile Low Cost 1500 VDC I/O Isolation SMD Minmax's MSLU100 1W DC/DC's are in "gull-wing" SMT package, weigh a mere 1.7 grams and meet IPC/JEDEC J-STD-020C 4th & 5th chapter in solder-reflow for lead free process. The series consists of 24 models with input voltages of 5V, 12V and 24VDC which offers standard single output voltages of 3.3V, 5V, 9V,12V, 15V, {5V, {12V and {15VDC for the choice. Their impressive guaranteed efficiencies enable all models to deliver their fully rated output power from -25] to +75] without heat sinking or forced-air cooling. The MSLU100 series is an excellent selection for a wide variety of applications including data communication equipments, distributed power systems, telecommunication equipments and industrial robot systems. The MSLU100 units are available in tape and reel package. Absolute Maximum Ratings Parameter Input Surge Voltage ( 1000 mS ) 5VDC Input Models 12VDC Input Models 24VDC Input Models Min. -0.7 -0.7 -0.7 ----Max. 9 18 30 260 450 Unit VDC VDC VDC ] mW Environmental Specifications Parameter Operating Temperature Operating Temperature Storage Temperature Humidity Cooling Conditions Ambient Case Min. -25 -25 -40 --Max. +75 +90 +125 95 Unit ] ] ] % Lead Temperature (1.5mm from case for 10 Sec.) Internal Power Dissipation Free-Air Convection Exceeding the absolute maximum ratings of the unit could cause damage. These are not continuous operating ratings. Leadfree Reflow Solder Process as per IPC/JEDEC J-STD-020C peak temp. 245C/10 sec. 1 MINMAX REV:10 2008/10 MSLU100 Series Model Selection Guide Model Number Input Voltage Output Voltage Output Current Input Current Load Regulation Efficiency VDC MSLU101 MSLU102 MSLU103 MSLU104 MSLU105 MSLU106 MSLU108 MSLU109 MSLU111 MSLU112 MSLU113 MSLU114 MSLU115 MSLU116 MSLU118 MSLU119 MSLU121 MSLU122 MSLU123 MSLU124 MSLU125 MSLU126 MSLU128 MSLU129 5 ( 4.5 ~ 5.5 ) 12 ( 10.8 ~ 13.2 ) 24 ( 21.6 ~ 26.4 ) VDC 3.3 5 9 12 15 {5 {12 {15 3.3 5 9 12 15 {5 {12 {15 3.3 5 9 12 15 {5 {12 {15 Max. mA 300 200 110 84 67 {100 {42 {33 300 200 110 84 67 {100 {42 {33 300 200 110 84 67 {100 {42 {33 Min. mA 6 4 2 1.5 1 {2 {0.8 {0.7 6 4 2 1.5 1 {2 {0.8 {0.7 6 4 2 1.5 1 {2 {0.8 {0.7 @Max. Load mA (Typ.) 271 256 254 259 254 270 259 254 112 109 106 106 105 113 108 104 58 54 54 55 53 57 54 53 @No Load mA (Typ.) 30 15 8 9 % (Max.) 10 10 10 8 7 10 8 7 8 8 8 5 5 8 5 5 8 8 8 5 5 8 5 5 @Max. Load % (Typ.) 73 78 78 78 79 74 78 78 74 76 78 79 80 74 78 79 72 78 77 77 79 73 78 78 Capacitive Load Models by Vout Maximum Capacitive Load # For each output 3.3V 33 5V 33 9V 33 12V 33 15V 33 {5V 33 {12V 33 {15V 33 Unit uF Input Fuse Selection Guide 5V Input Models 500mA Slow - Blow Type 12V Input Models 200mA Slow - Blow Type 24V Input Models 100mA Slow - Blow Type Input Specifications Parameter Input Voltage Range Model 5V Input Models 12V Input Models 24V Input Models Reverse Polarity Input Current Input Filter All Models Min. 4.5 10.8 21.6 --Typ. 5 12 24 --Max. 5.5 13.2 26.4 0.3 A VDC Unit Internal Capacitor REV:10 2008/10 MINMAX 2 MSLU100 Series Output Specifications Parameter Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20MHz) Ripple & Noise (20MHz) Ripple & Noise (20MHz) Temperature Coefficient Output Short Circuit Over Line, Load & Temp. Conditions Dual Output , Balanced Loads For Vin Change of 10% Io=20% to 100% Min. ------------0.5 Second Max. Typ. {0.1 {1.2 60 ----{0.01 Max. {1.0 {1.5 120 150 15 {0.02 Unit % % % mV P-P mV P-P mV rms %/] See Model Selection Guide General Specifications Parameter Isolation Voltage Rated Isolation Voltage Test Isolation Resistance Isolation Capacitance Switching Frequency MTBF Moisture Sensitivity Level (MSL) TEMPERATURE MIL-HDBK-217F @ 25], Ground Benign IPC/JEDEC J-STD-20 Conditions 60 Seconds Flash Tested for 1 Second 500VDC 100KHz,1V Min. 1500 1650 1000 --50 2000 Typ. ------40 100 --LEVEL 2 Max. ------100 140 --Unit VDC VDC M[ pF KHz K Hours Notes : 1. Specifications typical at Ta=+25], resistive load, nominal input voltage, rated output current unless otherwise noted. 2. Ripple & Noise measurement bandwidth is 0-20 MHz. 3. These power converters require a minimum output loading to maintain specified regulation. 4. Operation under no-load conditions will not damage these modules; however, they may not meet all specifications listed. 5 All DC/DC converters should be externally fused at the front end for protection. 6. Other input and output voltage may be available, please contact factory. 7. Specifications subject to change without notice. 8. It is not recommended to use water-washing process on SMT units. Block Diagram +Vo +Vin Bipolar Push-Pull Inverter -Vin -Vo -Vin +Vin Bipolar Push-Pull Inverter +Vo Com. -Vo 3 MINMAX REV:10 2008/10 MSLU100 Series 3.3V & 5V output types. +20% +15% +10% +5% Vnom -5% -10% 0% Max. Typ. Min. All other types. +20% +15% +10% +5% Vnom -5% -10% 100% +20% +15% +10% Max. +20% +15% +10% +5% Vnom Min. Output Voltage(%) Output Voltage(%) +5% Vnom -5% -10% 0% Typ. -5% -10% 100% 20% 40% 60% 80% 20% 40% 60% 80% Output Load Current (%) Output Load Current (%) Tolerance Envelopes Graph (3.3V & 5V Output) 100 90 Efficiency (%) Tolerance Envelopes Graph (All other Output) 100 90 Efficiency (%) 80 70 60 50 80 70 60 50 Low Nom Input Voltage (V) High Low Nom Input Voltage (V) High Efficiency vs Input Voltage (Single Output) 90 80 Efficiency (%) Efficiency (%) 10 20 40 60 80 70 60 50 40 30 20 100 Efficiency vs Input Voltage (Dual Output) 90 80 70 60 50 40 30 20 10 20 40 60 80 100 Load Current (%) Load Current (%) Efficiency vs Output Load (Single Output) 100 100LFM 80 Output Power (%) 400LFM 200LFM Efficiency vs Output Load (Dual Output) 60 Natural convection 40 20 0 -25 ~ 50 60 70 80 ] 90 100 110 Ambient Temperature Derating Curve REV:10 2008/10 MINMAX 4 MSLU100 Series Test Configurations Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0[ at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + Battery + Lin Current Probe +Vin +Out Load Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0[ at 100 KHz) capacitor of a 2.2uF for the 5V input devices, a 1.0uF for the 12V input devices and a 0.47uF for the 24V input devices. DC / DC Converter -Vin -Out Cin + DC Power Source + Cin +Vin DC / DC Converter -Vin +Out Load -Out Peak-to-Peak Output Noise Measurement Test Use a Cout 0.33uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin Single Output DC / DC Converter -Vin -Out +Out Copper Strip Cout Resistive Scope Load Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 3.3uF capacitors at the output. + DC Power Source -Vin +Vin Single Output DC / DC Converter -Out +Out +Vin Dual Output DC / DC Converter -Vin +Out Com. Copper Strip Cout Cout Scope Resistive Load Scope -Out Cout Load Design & Feature Considerations + +Vin +Out Dual Output Com. DC / DC Converter -Vin -Out Cout Load Maximum Capacitive Load The MSLU100 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. For optimum performance we recommend 33uF maximum capacitive load. The maximum capacitance can be found in the data sheet. DC Power Source - 5 MINMAX REV:10 2008/10 MSLU100 Series Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90° C. The derating curves are determined from measurements obtained in an experimental apparatus. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT REV:10 2008/10 MINMAX 6 MSLU100 Series Mechanical Dimensions Single Output Connecting Pin Patterns Top View ( 2.54 mm / 0.1 inch grids ) 8 2.1 [0.08] 5 0.28[0.01] 1.0 .5 R0 7.62mm 1.6mm 0~4 1 2 4 2.1 [0.08] 3.04 [0.12] 2.54 [0.10] 5.08 [0.2] ( Magnification of A ) 10.8mm 13.7 [0.54] 13.3 [0.52] 13.0 [0.51] 0.3C 8.0 [0.31] 0.1 [0.004] 4.65 [0.18] 1.6 [0.06] 6.7 [0.26] 7.0 [0.28] 2.54mm 1.0mm Min 0.3 [0.01] 0.6 [0.024] 1.5{ 0.1[0.06] 5.5 [0.22] 1.5 {0.1 [0.06] 0.15 5.5 [0.22] 11.0 { 0.2 [0.43] Dual Output 0.28 [0.01] R0 .5 10 2.1 [0.08] 7 1.0 1 2 4 5 7.62mm 1.6mm ( Magnification of A ) 2.1 [0.08] 3.04 [0.12] 2.54 [0.10] 5.08 [0.2] 16.24 [0.64] 15.85 [0.62] 15.55 [0.61] 0.3C 8.0 [0.31] 2.54 [0.10] 0~4 10.8mm 0.1 [0.004] 4.65 [0.18] 6.7 [0.26] 7.0 [0.28] 2.54mm 1.5 { 0.1 [0.06] 5.5 [0.22] 11.0{ 0.2[0.43] 0.15 1.0mm Min 1.6 [0.06] 0.6 [0.02] Tolerance Millimeters X.X{0.25 X.XX{0.10 0.3 [0.01] 1.5{ 0.1[0.06] Inches X.XX{0.01 X.XXX{0.004 {0.002 Pin {0.05 7 MINMAX REV:10 2008/10 MSLU100 Series Pin Connections Pin 1 2 3 4 5 6 7 8 9 10 Singles -Vin +Vin No Pin -Vout +Vout No Pin No Pin NA Dual -Vin +Vin No Pin Common -Vout No Pin +Vout No Pin No Pin NA Flammability NA: Not Available for Electrical Connection : UL94V-0 Weight : 1.7g (Single Output) 2.0g (Dual Output) Case Material : Non-Conductive Black Plastic Case Size (Dual) : 16.24*8.0*6.7 mm 0.64*0.31*0.26 inches Physical Characteristics Case Size (Single) : 13.7*8.0*6.7mm 0.54*0.31*0.26 inches REV:10 2008/10 MINMAX 8