MSLU314

MSLU300 Series 1W, High Isolation SMD, Single & Dual Output DC/DC Converters Key Features Efficiency up to 79% 3000VDC Isolation Low Cost Input 5, 12 and 24VDC Output 3.3, 5, 12, 15, {5, {12 and {15VDC Temperature Performance -25] to +75] UL 94V-0 Package Material Internal SMD Construction 3000 VDC SMD $ Low Cost Low Profile I/O Isolation Minmax's MSLU300 1W DC/DC's are in "gull-wing" SMT package. The series is designed to provide high levels of isolation 3000VDC. It consists of 21 models with input voltages of 5V,12V and 24VDC which offers standard output voltages of 3.3V, 5V, 12V, 15V, {5V, {12V and {15VDC for the choice. Their impressive guaranteed efficiencies enable all models to deliver their fully rated output power from -25] to +75] without heat sinking or forced-air cooling. The MSLU300 series is an excellent selection for a variety of applications including data communication equipments, distributed power systems, telecommunication equipments and industrial robot systems. The MSLU300 units are available in tape and reel package. Absolute Maximum Ratings Parameter Input Surge Voltage ( 1000 mS ) 5VDC Input Models 12VDC Input Models 24VDC Input Models Min. -0.7 -0.7 -0.7 ----Max. 9 18 30 300 550 Unit VDC VDC VDC ] mW Environmental Specifications Parameter Operating Temperature Operating Temperature Storage Temperature Humidity Cooling Conditions Ambient Case Min. -25 -25 -25 -Max. +75 +90 +125 95 Unit ] ] ] % Lead Temperature (1.5mm from case for 10 Sec.) Internal Power Dissipation Free-Air Convection Exceeding the absolute maximum ratings of the unit could cause damage. These are not continuous operating ratings. Leadfree Reflow Solder Process as per IPC/JEDEC J-STD-020C peak temp. 245C/10 sec. 1 MINMAX REV:5 2009/01/20 MSLU300 Series Model Selection Guide Model Number Input Voltage Output Voltage Output Current Input Current Load Regulation Efficiency VDC MSLU301 MSLU302 MSLU304 MSLU305 MSLU306 MSLU308 MSLU309 MSLU311 MSLU312 MSLU314 MSLU315 MSLU316 MSLU318 MSLU319 MSLU321 MSLU322 MSLU324 MSLU325 MSLU326 MSLU328 MSLU329 5 (4.5 ~ 5.5) 12 (10.8 ~ 13.2) 24 (21.6 ~ 26.4) VDC 3.3 5 12 15 {5 {12 {15 3.3 5 12 15 {5 {12 {15 3.3 5 12 15 {5 {12 {15 Max. mA 260 200 84 67 {100 {42 {34 260 200 84 67 {100 {42 {34 260 200 84 67 {100 {42 {34 Min. mA 5 4 2 1.5 {2 {0.8 {0.7 5 4 2 1.5 {2 {0.8 {0.7 5 4 2 1.5 {2 {0.8 {0.7 @Max. Load mA (Typ.) 238 267 255 251 267 255 255 98 110 105 103 110 105 106 51 57 53 53 57 53 54 @No Load mA (Typ.) 30 15 8 %(Max.) 10 10 7 7 10 7 7 10 8 5 5 8 5 5 10 8 5 5 8 5 5 @Max. Load % (Typ.) 72 75 79 80 75 79 80 73 76 80 81 76 80 80 70 73 79 79 73 79 79 Capacitive Load Models by Vout Maximum Capacitive Load # For each output 3.3V 33 5V 33 12V 4.7 15V 4.7 {5V # 10 {12V # 2.2 {15V # 2.2 Unit uF Input Fuse Selection Guide 5V Input Models 500mA Slow - Blow Type 12V Input Models 200mA Slow - Blow Type 24V Input Models 100mA Slow - Blow Type Input Specifications Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Model 5V Input Models 12V Input Models 24V Input Models All Models Min. 4.5 10.8 21.6 --Typ. 5 12 24 --Max. 5.5 13.2 26.4 0.3 A VDC Unit Internal Capacitor REV:5 2009/01/20 MINMAX 2 MSLU300 Series Output Specifications Parameter Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20MHz) Ripple & Noise (20MHz) Ripple & Noise (20MHz) Temperature Coefficient Output Short Circuit Over Line, Load & Temp. Conditions Dual Output, Balanced Loads For Vin Change of 1% Io=20% to 100% Min. ------------0.5 Second Max. Typ. {0.1 {1.2 75 ----{0.01 Max. {1.0 {1.5 100 150 15 {0.02 Unit % % % mV P-P mV P-P mV rms %/] See Model Selection Guide General Specifications Parameter Isolation Voltage Rated Isolation Voltage Test Isolation Resistance Isolation Capacitance Switching Frequency MTBF MIL-HDBK-217F @ 25], Ground Benign Conditions 60 Seconds Flash Tested for 1 Second 500VDC 100KHz,1V Min. 3000 3300 10 --50 2 Typ. ------60 100 --Max. ------100 150 --Unit VDC VDC G[ pF KHz M Hours Notes : 1. Specifications typical at Ta=+25], resistive load, nominal input voltage, rated output current unless otherwise noted. 2. Ripple & Noise measurement bandwidth is 0-20 MHz. 3. These power converters require a minimum output loading to maintain specified regulation. 4. Operation under no-load conditions will not damage these modules; however, they may not meet all specifications listed. 5. All DC/DC converters should be externally fused on the front end for protection. 6. Other input and output voltage may be available, please contact factory. 7. Specifications subject to change without notice. 8. It is not recommended to use water-washing process on SMT units. Block Diagram Single Output Dual Output +Vo +Vin Bipolar Push-Pull Inverter -Vin -Vo -Vin +Vin Bipolar Push-Pull Inverter +Vo Com. -Vo 3 MINMAX REV:5 2009/01/20 MSLU300 Series 3.3V & 5V output types. +20% +15% +10% +5% Vnom -5% -10% 0% Max. Typ. Min. All other types. +20% +15% +10% +5% Vnom -5% -10% 100% +20% +15% +10% Max. +20% +15% +10% +5% Vnom Min. Output Voltage(%) Output Voltage(%) +5% Vnom -5% -10% 0% Typ. -5% -10% 100% 20% 40% 60% 80% 20% 40% 60% 80% Output Load Current (%) Output Load Current (%) Tolerance Envelopes Graph (3.3V & 5V Output) Tolerance Envelopes Graph (All other Output) REV:5 2009/01/20 MINMAX 4 MSLU300 Series Test Configurations Peak-to-Peak Output Noise Measurement Test Use a Cout 0.33uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out To Oscilloscope Single Output DC / DC +Converter + Lin -Vin Battery -Out Cin Copper Strip +Vin +Out Resistive Cout Scope Load DC / DC Current Load Converter Probe Copper Strip -Vin -Out + DC Power Source -Vin +Vin Single Output DC / DC Converter -Out +Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 1.0uF capacitors at the output. Cout Load +Vin Dual Output DC / DC Converter -Vin +Out Com. -Out Copper Strip Cout Copper Strip Cout Copper Strip Scope Scope Resistive Load + DC Power Source -Vin +Vin +Out Dual Output Com. DC / DC Converter -Out Cout Load Design & Feature Considerations Maximum Capacitive Load The MSLU300 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. The maximum capacitance can be found in the data sheet. Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90° C. The derating curves are determined from measurements obtained in an experimental apparatus. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0[ at 100 KHz) capacitor of a 2.2uF for the 5V input devices, a 1.0uF for the 12V input devices and a 0.47uF for the 24V devices. + DC Power Source + Cin -Vin -Out +Vin DC / DC Converter +Out Load Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT 5 MINMAX REV:5 2009/01/20 MSLU300 Series Mechanical Dimensions Connecting Pin Patterns Top View ( 2.54 mm / 0.1 inch grids ) 12 11 10 8 7 0.25 [0.01] 5.08mm 0~4 8.0 R0 .5 1.9mm 1 2 3 5 6 ( Magnification of A ) 16.3 [0.64] 15.9 [0.63] 15.6 [0.61] 12mm 1.8 2.54 2.54 [0.07] [0.100] [0.100] 5.08 [0.200] 2.54 [0.100] 2.54mm 7.67 [0.30] 8.0 [0.31] 10.1mm 1.0mm Min. 0.6 [0.02] 0.33 [0.01] 1.5 { 0.1 [0.06 {0.004] 5.5 [0.22] 5.5 [0.22] 1.5 { 0.1 [0.06 { 0.004] 11.0 { 0.2 [0.43 { 0.008] Tolerance Millimeters X.X{0.25 X.XX{0.13 Inches X.XX{0.01 X.XXX{0.005 {0.002 Pin {0.05 Pin Connections Pin 1 2 3 5 6 7 8 10 11 12 Single Output -Vin +Vin NA -Vout NA NA +Vout NA NA NA Dual Output -Vin +Vin NA Common -Vout NA +Vout NA NA NA Physical Characteristics Case Size : 16.3*8.0*7.67 mm 0.64*0.31*0.30 inches Non-Conductive Black Plastic 2g UL94V-0 Case Material Weight Flammability : : : NA : Not Available for Electrical Connection REV:5 2009/01/20 MINMAX 6