MT8982AE

® ISO-CMOS ST-BUS™ FAMILY MT8982 Small Digital Switch (MiniDX) Features • • • • • • • • ST-BUS/GCI compatible switch matrix 64 channel non-blocking time switch 2 x 32 channel serial inputs and outputs Per-channel tristate control 4-pin serial microprocessor interface Patented message mode Low power consumption (10 mW) Single 5 volt supply ISSUE 6 May 1995 Ordering Information MT8982AE 16 Pin Plastic DIP MT8982AS 16 Pin SOIC MT8982AN 20 Pin SSOP -40 to +85°C Description The MT8982 Small Digital Switch (MiniDX) is a nonblocking CMOS time switch with a capacity of up to 64 - 8 bit Time Division Multiplexed (TDM) encoded voice or data channels. It is a size-optimized version of MITEL's successful MT8980D Digital Switches, providing switching capability in cost sensitive applications such as telephone sets and digital key systems. The TDM interface to the device is via two pairs of 2048 kbit/s serial streams with 32 64 kbit/s channels per stream (ST-BUS). A serial microport provides access to the device for programming the required connections. The serial microport is compatible with most common microcontrollers. The unique message mode capability allows the MT8982 to act as a controller for other members of MITEL's ST-BUS family of components. Applications • • • • • • Cost sensitive digital switching applications Digital key telephone systems GCI/ST-BUS conversion ST-BUS device control interface ISDN telephone set support circuit Interprocessor communication STi0 STi1 Serial to Parallel Converter 64 x 8 Data Memory Output Mux Parallel to Serial Converter STo0 STo1 F0i C4i F0o Address Counters Address Mux Data Mux RxD/CSTi0 TxD/NC SCLK/CSTi1 CS/CMS MPS Address Mux ODE Serial Microport 64 x 9 Connect Memory 3-State Control Figure 1 - Functional Block Diagram 2-31 MT8982 ISO-CMOS STi0 STi1 STo0 STo1 RxD/CSTi0 TxD/NC SCLK/CSTi1 VSS 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD ODE IC MPS F0o F0i C4i CS STi0 STi1 NC STo0 STo1 RxD/CSTi0 TxD/NC NC SCLK/CSTi1 VSS 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VDD ODE IC MPS F0o NC F0i NC C4i CS 16 PIN PLASTIC/SOIC 20 PIN SSOP Figure 2 - Pin Connections Pin Description Pin # Name 16 1-2 3-4 5 20 1-2 4-5 6 STi0STi1 STo0STo1 RxD/ CSTi0 Serial TDM Input 0 and 1 (Inputs). 2048 kbit/s input data streams containing 32 8-bit channels synchronized to F0i. Serial TDM Output 0 and 1 (Outputs). 2048 kbit/s output data streams containing 32 8-bit channels synchronized to F0i. Received Data/Control Stream Input 0 (Input). When MPS is low, this pin receives serial microport data clocked in by the rising edge SCLK. When MPS is high, this pin receives a 2048 kbit/s serial TDM stream containing 32 8-bit channels, which are written into the Connect Memory locations corresponding to STo0. Transmit Data (Output). When MPS is low, serial microport data is clocked out on this pin by the falling edge of SCLK. When MPS is high this output is disabled. Serial Microport Clock/Control Stream Input 1 (Input). When MPS is low, this pin receives a clock which is used to clock data to/from a microcontroller via a serial microport. When MPS is high, this pin receives a 2048 kbit/s serial TDM stream containing 32 8-bit channels, which are written into the Connect Memory locations corresponding to STo1. Power Input. Negative supply (ground). Chip Select (Input). When MPS is low, a low on this pin enables the serial microport. A high on this pin disables RxD and tristates TxD. When MPS is high, this pin must be low. Serial TDM Clock (Input). This clock input is used to clock the TDM data into and out of the device and refreshes the internal dynamic RAM. The clock rate is 4.096 MHz and data is clocked in on the rising edge of C4i three-quarters of the way through a bit period. Frame Pulse (Input). This input is the frame synchronization pulse for the 2048 kbit/s serial TDM streams. It may be either active low stradling the frame boundary (ST-BUS) or active high at the beginning of timeslot 5 (GCI). Frame Pulse (Output). This pin outputs a frame pulse in the opposite format to F0i (GCI or ST-BUS) delayed or advanced by five channels. Microport Select (Input). When this pin is held low, the serial microport is in normal mode. When this pin is high, the microport is in serial bus mode. Internal Connection. Tie to VSS for normal operation. Output Drive Enable (Input). When this pin is held high, the STo0 and STo1 output drivers function normally. When this pin is low, STo0 and STo1 are tristated. NB: When ODE is high, individual channels on STo0 and STo1 can be tristated under software control. Power Input. Positive supply. No Connection. Description 6 7 7 9 TxD SCLK/ CSTi1 8 9 10 10 11 12 VSS CS C4i 11 14 F0i 12 13 14 15 16 17 18 19 F0o MPS IC ODE 16 20 3,8, 13,15 VDD NC 2-32 ISO-CMOS Functional Description The MT8982 (MiniDX) provides cost effective time switching capability for small size applications utilizing up to two serial Time Division Multiplexed (TDM) streams. Each TDM stream consists of 32 64 kb/s channels, giving the MiniDX a maximum capacity of 64 channels. The input framing signal may be either a ST-BUS or a GCI frame pulse. The MT8982 will output a delayed or advanced frame pulse in the opposite format to permit conversion between the two formats. The MiniDX can switch data from any channel in one of the two serial input TDM streams to any channel in either of the two serial output TDM streams. The microcontroller controlling the MiniDX writes to the MT8982 Connect Memory to establish the connection between the required input TDM channel and the selected output TDM channel(s). By reading the Connect Memory the microcontroller can check switched connections which have already been established. The MiniDX can also operate in message mode where the microcontroller transmits the data on the TDM serial stream. The microcontroller writes to the MT8982 Connect Memory to transmit data on the required output TDM channels. Reading the Data Memory of the MT8982 allows the microcontroller to receive messages from TDM input channels. These operations are useful for control of other ST-BUS components or for interprocessor communication. MT8982 formatted frame pulse is active high at the beginning of timeslot 5 (relative to the MT8982) and idles low. The MT8982 automatically determines the type of frame pulse from the level of the idle over five clock periods. A ST-BUS formatted frame pulse resets the internal address counters to zero. A GCI formatted frame pulse resets the counters to five. F0o outputs a frame pulse in the opposite format. If F0i is a ST-BUS formatted frame pulse, F0o will be a GCI formatted frame pulse delayed by five channels after F0i. If F0i is a GCI formatted frame pulse, F0o will be a ST-BUS formatted frame pulse delayed by 27 channels (32-5). During normal operation every second falling edge of the clock marks a timeslot boundary and the input data is clocked in by the rising edge, three-quarters of the way into the bit cell. The master clock must be 4.096 MHz for the F0o signal to be valid and to receive a GCI formatted F0i. Data which is output onto a TDM serial output channel may come from two sources; the Data Memory or the Connect Memory. If a channel is configured in connection mode, the source of output data is the Data Memory. If a channel is configured in message mode, the source of the output data is the Connect Memory. Data destined for a particular channel on the serial output links is read from the data or connect memory in the previous channel timeslot. This allows for delay in RAM access and parallel-to-serial conversion. Each output data channel can also be placed in tristate mode. When an output channel is in connection mode, the TDM output data is read from a Data Memory location pointed to by an address stored in the 64x8 bit Connect Memory. The Connect Memory locations are addressed sequentially, with each location corresponding to an output TDM link/ channel. In the channel time before the data is to be output, the contents of each Connect Memory location are output to the address bus of the Data Memory. The contents of the Data Memory at the selected address are then transferred to the parallelto-serial converter. The parallel-to-serial converter outputs onto the TDM serial stream during the correct channel time. By having the output channel specify the input channel, the user can route the same input channel to several output channels. This function is useful for broadcasting or resource channel uses. Hardware Description TDM Interface The MT8982 continuously receives TDM serial data at 2048 kbit/s through two serial inputs. These serial streams are then converted into a parallel format and stored sequentially in a 64x8 bit Data Memory. The sequential addressing is generated by an internal counter that is reset by the input 8 kHz frame pulse (F0i) which marks the frame boundaries of the incoming serial data stream. This counter increments with each timeslot so that it matches the binary count of the timeslot of the incoming data. The TDM timeslot count always corresponds to the ST-BUS channel positions. An extra address bit is used to differentiate between the two input data streams. The input 8 kHz frame pulse may be either ST-BUS or GCI formatted. A ST-BUS formatted frame pulse is an active low signal which straddles the frame boundary. It idles high the rest of the time. A GCI 2-33 MT8982 ISO-CMOS Microcontroller Interface The MT8982 is controlled via a synchronous, serial microport. The microport is compatible with Intel's MCS-51 serial port Mode 0 specifications, Motorola's Serial Peripheral Interface (SPI) specifications, and National's MicroWire specifications. The port consists of a transmit data line (TxD), a receive data line (RxD), a chip select line (CS), and a synchronous clock input (SCLK). All memory locations and control functions on the MiniDX are accessed through this port. The microport may also be configured in serial bus mode where data is clocked into the Connect Memory in the same way as STi0 and STi1 are clocked into Data Memory. In serial microport mode, CS must be low to enable a microport access. SCLK clocks the serial microport data in or out through RxD and TxD, LSB first. The TxD output driver is tristated when it is inactive. This allows RxD and TxD to be connected together for a single TxD/RxD line as used in the INTEL MCS-51 microcontrollers. Figure 3 shows a serial microport access cycle. A microport access cycle (microcycle) begins with a falling edge on CS. Eight bits of data are clocked into RxD by the rising edge of SCLK. Two of these eight bits indicate whether the microcycle operation is a read or a write, the rest of the bits are used for addressing. These eight bits are defined as the command/ address byte (Table 1). If the microcyle operation is a write, another eight bits are clocked When an output channel is in message mode, the data for the output channel originates from the microcontroller. The microcontroller writes data to the Connect Memory location which corresponds to the output link and channel number. The contents of the Connect Memory are transferred directly to the serial-to-parallel converter one channel time before it is to be output. The Connect Memory data is output MSB first, repetitively once per frame, until it is changed by the microcontroller. If the output channel is configured in tristate mode, the TDM serial stream output will be placed in high impedance during that channel time. This mode is entered by configuring the channel into connection mode and then setting the tristate control bit. All channels on both output TDM streams can be tristated by pulling pin 16 (ODE) low. This overrides the individual channel programming. The Data and Connect Memories are dynamic memories. They are refreshed by the sequential addressing generated by C4i. RxD COMMAND/ADDRESS Œ DATA INPUT/OUTPUT Œ  COMMAND/ADDRESS D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 TxD D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 SCLK  CS Ž Œ Minimum delay between accesses equals 3.0 µsec.  The Mini Dx: - latches received data in on the rising edge of SCLK - outputs transmit data on the falling edge of SCLK Ž The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted. Subsequent byte is always data.  Subsequent write microcycles may flow without raising CS. CS must go high after a read microcycle.  Figure 3 - Serial Microport Timing 2-34 ISO-CMOS into RxD by the rising edges of the next eight SCLK cycles. If the operation is a read, eight data bits are clocked from TxD by the falling edges of the next eight SCLK cycles. The rising edge of CS tristates TxD after the last transmitted bit. Successive write microcycles can take place while CS remains low, with each microcycle following the sequence of a command/address byte followed by a data byte. CS must go high after a read microcycle. Note that a command/address byte must always follow the high to low transition on CS. When the MPS input is pulled high and the CS input is pulled low, the microport is put into serial bus mode. Pins RxD and SCLK become CSTi0 and CSTi1, respectively, and are configured as 2048 kbit/ s serial streams with 32 channels each. The frame and timeslot boundaries are determined by F0i and C4. Each channel on CSTi0 and CSTi1 is stored in the connect memory address corresponding to the link and channel number. The Data Memory and the Connect Memory cannot be read when the microport is in serial bus mode. Device Timing MT8982 During each TDM timeslot, eight read or write operations occur internally in the MT8982. These are shown in Figure 4. During the first two bit periods, data received in the previous timeslot on the two input TDM streams is loaded into the Data Memory. Bit periods 2 and 6 are serial microport access windows; data may be read from, or written to any accessible memory location. During bit periods 3 and 5, data is read from the connect memory for the next timeslot on links 0 and 1 respectively. The Data Memory locations which are addressed by the previous reads of the connect memory are accessed during bit periods 4 and 7. When the microport is in serial bus mode, bit periods 2 and 6 have a slightly different function. Data from the previous timeslot of CSTi0 and CSTi1 respectively is written to the corresponding connect memory locations. The transfer of information from the input TDM streams to the output TDM streams results in a delay through the MT8982. This delay is dependent only on the combination of source and destination Description Bit 7 2-6 Name Stream Ch0-Ch4 Stream. This is the most significant bit of the address for the memory location that is to be accessed. It corresponds to one of the TDM serial streams (0-1). Channel 0-4. These bits are the five least significant bits of the address for the memory location that is to be accessed. The binary value of these bits correspond to a TDM channel (0-31). Command Select 0-1. These two bits define the four command operations for the MT8982. The destination addressed by the command is defined in bits 2-7 of the Command/Address byte. Cmd0-Cmd1 0-0 0-1 1-0 1-1 Read from Connect Memory. Write to Connect Memory and set connection mode. Read Data Memory. Write to Connect Memory and set message mode. Table 1. Command Address Byte Description Unused. Output Drive Enable. When this bit is set, the addressed TDM channel is placed in tristate. When low, the output is enabled. Input Stream. This bit defines the input TDM stream from which the output data is sourced (0-1). Source Channel 0-4. The binary value of these bits defines the input channel from which the output data is sourced (0-31). Table 2. Connect Memory Connection Mode Data Byte 2-35 0-1 Cmd0-Cmd1 Bit 7 6 5 0-4 Name NA ODE STi SC0-SC4 MT8982 ISO-CMOS Channel 31 Channel 0 F0i C4 Bit 0 Microport Mode Wr DM Link 0 Ch 31 Bit 1 Wr DM Link 1 Ch 31 Bit 2 µP Bit 3 Rd CM Link 0 Ch 1 Bit 4 Rd DM Link 0 Ch 1 Bit 5 Rd CM Link 1 Ch 1 Bit 6 µP Bit 7 Rd DM Link 1 Ch 1 Serial Port Mode Wr CM Link 0 Ch 31 Wr CM Link 1 Ch 31 Figure 4 - Internal Memory Access Windows channels and is not dependent on the input and output streams. The delays are given in Table 3. The maximum delay is one frame plus one channel; the minimum delay is two channels. Input Channel n n Output Channel m = n, n+1 m > n+1 Device Programming Microport Mode In serial microport mode, the MT8982 is programmed and read using microcycles which consist of a command/address byte followed by a data byte. The Command/Address Byte is shown in Table 1. Bits 0 and 1 are the command bits (Cmd0-1), and are used to indicate the type of microcycle access. The microcontroller can read the Data Memory, read or write the Connect Memory, and set per-channel message or connection mode. Bits 2 to 6 of the command/address byte (Ch0-Ch4) correlate to a channel on a TDM stream (0-31). Bit 7 (STREAM) correlates to stream 0 or stream 1. These bits address the corresponding Data Memory or Connect Memory location. The microcycle operations selected command/address byte are as follows: Read Connect Memor y (Cmd0-1: 0,0) Bits 0 to 7 of the addressed Connect Memory location will be transmitted to the microcontroller in the following data byte. Depending on what the last Connect Memory write mode was, the data transmitted could be a message byte or a Connection Mode data byte. by the Delay m- n + 32 channels m- n channels n m