SC-2A

PRODUCT INFORMATION 860nm 1A255 High-Performance LED Baseband Video The low thermal droop of this device allows baseband video transmission with minimum distortion. The double-lens optical system provides for optimum coupling of power into the fiber. Optical and Electrical Characteristics PARAMETER SYMBOL MIN. TYP . MAX. UNIT (25° C Case Temperature) TEST CONDITION Fiber-Coupled Power (Fig.1, 2,& 3) (Table 1) Pfiber tr, tf fc l Pl p 80 120 6 55 8 W ns MHz IF =80 mA (Note 1) Fiber: 62.5/125 m Graded Rise and Fall Time (10-90%) IF =80 mA (no bias) Bandwidth (3dBel) IF =80 mA IF =80 mA IF =80 mA IF =80 mA IF =80 mA VR=1V Index NA=0.275 Thermal Droop (nonlinearity) (Note 2) 2 840 860 50 880 % nm nm 2.2 20 V A pF Peak Wavelength Spectral Width (FWHM) Forward Voltage (Fig.5) Reverse Current Capacitance VF IR C 1.8 250 VR= 0V, f=1 MHz Note 1: Measured at the exit of 100 meters of fiber. Note 2: Transient decline in optical power due to self-heating. Ø4.7 Ø1.5 0.6 Absolute Maximum Ratings PARAMETER SYMBOL LIMIT 3.7 Storage Temperature 14 Tstg Top Ptot IF IFRM VR Tsld -55 to +125 C -55 to +125 C 250 mW 110 mA 180 mA 1.5 V 260 C Operating Temperature (derating: Fig.4) Electrical Power Dissipation (derating: Fig.4) Continuous Forward Current (f 10 kHz) 50%, f 1 MHz) 0.4 CASE CATHODE ANODE All dimensions in mm Peak Forward Current (duty cycle Reverse Voltage 2.5 5.4 BOTTOM VIEW Soldering Temperature (2mm from the case for 10 sec) The anode is in electrical contact with the case. TO-46 Package With Lens Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink Thermal Resistance - No Heat Sink Rthjc -0.5 0.3 100 400 C/W C/W %/ C nm/ C Rthja Temperature Coefficient - Optical Power dP/dTj Temperature Coefficient -W avelength d /dTj 12090.11 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 High-Performance LED 1A255 860nm Typical Fiber-Coupled Power Core Diameter/Cladding Diameter Numerical Aperture 50/125 m 0.20 62.5/125 m 0.275 100/140 m 0.29 200/230 m 0.37 RELATIVE FIBER-COUPLED POWER % 100 FIGURE 1 % 100 FIGURE 2 r z = opt. Øc = 62.5ʵm RELATIVE FIBER-COUPLED POWER 80 80 z 60 W Table 1 120 W 250 W 400 W 60 60 40 40 r 20 r = opt. Øc = 62.5ʵm z 20 0 0.5 1.0 1.5 2.0 2.5 3.0 mm 0 0 20 40 60 80 100 µm z - AXIAL DISPLACEMENT OF FIBER r - RADIAL DISPLACEMENT OF FIBER % 100 FIGURE 3 MAX. ELECTRICAL POWER DISSIPATION mW 300 FIGURE 4 SHORT WAVELENGTH LED 150¡C RELATIVE FIBER-COUPLED POWER 80 50% DUTY CYCLE 200 60 DC INFINITE HEAT SINK NO HEAT SINK 40 100 20 HEAT SINKED 0 0 40 80 120 160 200 mA 0 0 50 100 FORWARD CURRENT OPERATING TEMPERATURE mA 200 FIGURE 5 FORWARD CURRENT 100 0 0 1 2 3V FORWARD VOLTAGE Clip for SC-2A R 1.00 3.3000 5.6000 80,000 20.8200 0.5000 10,2500 10.3000 4.9500 0.5000 4.5000 5.0800 3.6450 Clip for Pigtail-3A 10.70 0.50 10.25 10.30 4.95 0.50 4.50 0.85 5.08 3.65 PRODUCT INFORMATION ST -2A Package Emitter or Detector in ST ® Package Mitel emitters and detectors can be provided in this low-profile ST ® package. The device is electrically isolated from the ST ® receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature ST-2A (Note 1) Tstg , Top -40 to +85 C Note 1: Temperature range can be extended to -55° to +125°C on request. Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink (Note 2) Rthcc Rthca Rthca 80 40 200 C/W C/W C/W Thermal Resistance - No Heat Sink (Note 2) Thermal Resistance - On PC Board (Note 2) Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance. 2-56 UNC - 2B max.0.5 3/8"-32 UNEF FIBER END MARKING SIDE SLOT SIDE 0.006 Ø2.502 +0.01 0 12.7 9.5 Ø2.5 +0 -0.004 7.89 7.6 min.12 3.9 5.4 20.1 MATING FERRULE* (not included) All Dimensions in mm *The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in ST-2A Housing (ST is a registered trademark of AT&T) 103326 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION SMA-2A Package Emitter or Detector in SMA Package Mitel emitters and detectors can be provided in this low-profile SMA package. The device is electrically isolated from the SMA receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature SMA-2A (Note 1) Tstg , Top -40 to +85 C Note 1: Temperature range can be extended to -55° to +125°C on request. Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink (Note 2) Rthcc Rthca Rthca 80 40 200 C/W C/W C/W Thermal Resistance - No Heat Sink (Note 2) Thermal Resistance - On PC Board (Note 2) Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance. 2-56 UNC - 2B max.0.5 12.7 9.5 Ø3.176 +0.01 0 1/4"-36UNS MARKING SIDE FIBER END Ø3.174 +0 -0.004 0.006 3.9 7.2 min.12 5.7 15.2 9.8 ± 0.03 MATING FERRULE* (not included) All Dimensions in mm *The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in SMA-2A Housing 103325 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION SC-2A Package Emitter or Detector in SC Package Mitel emitters and detectors can be provided in this low-profile SC package. The device is electrically isolated from the SC receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber.. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature Tstg , Top -40 to +85 C Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink (Note 1) Rthcc Rthca Rthca 125 40 200 C/W C/W C/W Thermal Resistance - No Heat Sink (Note 1) Thermal Resistance - On PC Board (Note 1) Note 1: Add Rthjc for emitter or detector to estimate the total thermal resistance. 2.5 Ø2.3 1. 4 x4 12 MARKING / SLOT SIDE 0.006 13 FIBER END Ø2.5 +0 -0.004 Ø7.5 22 18 7.95 MATING FERRULE* (not included) 8.9 min. 12 18 All Dimensions in mm * The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in SC-2A Housing 105967 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION Pigtail-3A Package Emitter or Detector in Pigtail Package Mitel emitters and detectors can be provided in this pigtail package with a wide selection of fiber types. The device is electrically isolated from the pigtail receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. A special design maximizes the return loss for detectors in this package. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature (Note 1 & 2) Tstg , Top - 40 to +85 C Note 1: Temperature range can be extended to -55/+125 C on request. Note 2: Temperature range may be limited by the specification of the fiber. Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink (Note 3) Rthcc Rthca Rthca 120 25 250 C/W C/W C/W Thermal Resistance - No Heat Sink (Note 3) Thermal Resistance - On PC-Board (Note 3) Note 3: Add Rthjc for LED to estimate the total thermal resistance. Optical Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Return Loss 10/125 m fiber (PIN only) RL 40 55 dB MARKING Ø6.00 Ø6 min.12 13 All Dimensions in mm Mechanical Outline of Diode in PIGTAIL-3A Housing 105429 1997-07-03 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION FC-2A Package Emitter or Detector in FC Package Mitel emitters and detectors can be provided in this low-profile FC package. The device is electrically isolated from the FC receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature FC-2A (Note 1) Tstg , Top -40 to +85 C Note 1: Temperature range can be extended to -55° to +125°C on request. Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink (Note 2) Rthcc Rthca Rthca 80 40 200 C/W C/W C/W Thermal Resistance - No Heat Sink (Note 2) Thermal Resistance - On PC Board (Note 2) Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance. min.12 5.6 2.0 5.50 Ø 2.2 MARKING/ SLOT SIDE 0.006 Ø 2.5 13.4 FIBER END Ø2.5 M8x0.75 Thread +0 -0.004 19 08 7.95 MATING FERRULE* (not included) 9.2 max. 0.5 All Dimensions in mm * The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in FC-2A Housing 105515 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 http://www.mitelsemi.com World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s conditions of sale which are available on request. M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE