SP8830ADG

1.5GHz ÷ 10 Prescaler Advance Information DS3690 Issue 3.3 June 1999 SP8830 Features q q Ordering Information SP8830 A DG SP8830 B DG DES9157201/AC/DGAZ (SMD) High Speed Operation 1·5GHz Silicon Technology for Low Phase Noise (Typically Better Than 2140dBc / Hz at 10kHz) Very Low Power Dissipation: 150mW (Typ.) Single 5V Supply Operation High Input Sensitivity Very Wide Operating Frequency Range Available as DESC SMD 5962 - 9157201MPA q q q q q q Temperature Range: 255°C to 1125°C (A Grade) 240°C to 185°C (B Grade) Absolute Maximum Ratings Description The SP8830 is one of a range of very high speed low power prescalers for professional and military applications. The device features a complementary output stage with on chip current sources for the emitter follower outputs. Supply voltage, VCC Clock input voltage Storage temperature range Junction temperature - 6.5V 2.5V p-p 65° C to +150°C + 175°C 1 1·25k 1k 2k 7 6 1·25k VCC OUTPUT OUTPUT 42 INPUT INPUT 2 45 1mA 0·8mA 3 0·8mA 5 GND Figure 1 SP8830 block diagram SP8830 Advance Information VCC INPUT INPUT NC 1 2 3 4 8 7 6 5 NC OUTPUT OUTPUT GND DG8 Figure 2 Pin connections Electrical Characteristics Unless otherwise stated, the Electrical Characteristics are guaranteed over specified supply, frequency and temperature range Supply voltage, VCC -4·75V to +5·25V Temperature, TAMB = -55°C to +125°C (A Grade), -40°C to +85°C (B Grade) Characteristic Supply current, ICC Input sensitivity, 100MHz to 1500MHz Input impedance (series equivalent) Output voltage with fIN = 100MHz Output voltage with fIN = 1500MHz Pin Min. 1 2, 3 Value Typ. 40 Max. 50 100 Units mA mV Ω pF V p-p V p-p RMS sinewave, measured in 50Ω system. See Figs 3 and 4. See Fig. 5 Conditions 2, 3 6, 7 6, 7 0·7 50 2 1 0·4 400 * Tested as specified VIN (mV RMS INTO 50 Ω ) 150 GUARANTEED * OPERATING WINDOW in table of Electrical Characteristics 100 50 100 500 1000 FREQUENCY (MHz) 1500 2000 Figure 3 Typical input sensitivity 2 Advance Information SP8830 POWER METER SIGNAL GENERATOR COAXIAL SWITCH 50 Ω 15V 1 8 FROM 0·1µ OUTPUT 50 Ω 1k 3p Output load for amplitude measurements 1n 2 3 7 6 5 SP8830 RATIO COUNTER 0·1µ 1n 4 Figure 4 Test circuit j1 j 0.5 j2 j 0.2 j5 0 0.2 0.5 1 2 5 100MHz 2j 5 2j 0.2 1500MHz 1000MHz 2j 1 2j 2 500MHz 2j 0.5 Figure 5 Typical input impdance, normalised to 50Ω 3 http://www.mitelsemi.com World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s conditions of sale which are available on request. M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE