CM150DU-24NFH_09

MITSUBISHI IGBT MODULES CM150DU-24NFH HIGH POWER SWITCHING USE CM150DU-24NFH ¡IC ................................................................... 150A ¡VCES ......................................................... 1200V ¡Insulated Type ¡2-elements in a pack APPLICATION High frequency switching use (30kHz to 60kHz). Gradient amplifier, Induction heating, power supply, etc. OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm TC measured point 94 7 17 80 ±0.25 23 23 2–φ6.5 MOUNTING HOLES 4 E2 G2 24 C2E1 E2 C1 18 G1E1 4 11 48 12 3–M5NUTS 12mm deep 16 2.5 25 2.5 16 13.5 E2 G2 TAB 7.5 4 #110. t=0.5 C2E1 E2 13 CM C1 G1 E1 30 –0.5 +1 LABEL 21.2 CIRCUIT DIAGRAM Feb. 2009 MITSUBISHI IGBT MODULES CM150DU-24NFH HIGH POWER SWITCHING USE MAXIMUM RATINGS Symbol VCES VGES IC ICM IE (Note 1) IEM (Note 1) PC (Note 3) PC’ (Note 3) Tj Tstg Viso — — — (Tj = 25°C, unless otherwise specified) Parameter Collector-emitter voltage Gate-emitter voltage Collector current Emitter current Maximum collector dissipation Maximum collector dissipation Junction temperature Storage temperature Isolation voltage Mounting torque Weight G-E Short C-E Short Operation Pulse Operation Pulse TC = 25°C TC’ = 25°C*4 Conditions (Note 2) (Note 2) (Note 2) (Note 2) Terminals to base plate, f = 60Hz, AC 1 minute Main terminals M5 screw Mounting M6 screw Typical value Ratings 1200 ±20 150 300 150 300 650 960 –40 ~ +150 –40 ~ +125 2500 2.5 ~ 3.5 3.5 ~ 4.5 310 Unit V V A A A A W W °C °C Vrms N•m N•m g ELECTRICAL CHARACTERISTICS Symbol ICES VGE(th) IGES VCE(sat) Cies Coes Cres QG td(on) tr td(off) tf trr (Note 1) Qrr (Note 1) VEC(Note 1) Rth(j-c)Q Rth(j-c)R Rth(c-f) Rth(j-c’)Q Rth(j-c’)R RG Parameter Collector cutoff current (Tj = 25°C, unless otherwise specified) Test conditions VCE = VCES, VGE = 0V IC = 15mA, VCE = 10V ±VGE = VGES, VCE = 0V IC = 150A, VGE = 15V VCE = 10V VGE = 0V VCC = 600V, IC = 150A, VGE = 15V VCC = 600V, IC = 150A VGE = ±15V RG = 2.1Ω, Inductive load IE = 150A IE = 150A, VGE = 0V IGBT part (1/2 module) FWDi part (1/2 module) Case to heat sink, Thermal compound Applied*2 (1/2 module) IGBT part (1/2 module) FWDi part (1/2 module) Tj = 25°C Tj = 125°C Min. — 4.5 — — — — — — — — — — — — — — — — — — — 2.1 Limits Typ. — 6 — 5.0 5.0 — — — 680 — — — — — 7.5 — — — 0.07 — — — Max. 1 7.5 0.5 6.5 — 24 2.0 0.45 — 150 80 400 150 150 — 3.5 0.19 0.35 — 0.13*3 0.21*3 21 Unit mA V µA V nF nF nF nC ns ns ns ns ns µC V K/W K/W K/W K/W K/W Ω Gate-emitter threshold voltage Gate leakage current Collector-emitter saturation voltage Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Turn-on delay time Turn-on rise time Turn-off delay time Turn-off fall time Reverse recovery time Reverse recovery charge Emitter-collector voltage Thermal resistance*1 Contact thermal resistance Thermal resistance*4 External gate resistance *1 : Case temperature (TC) measured point is shown in page OUTLINE DRAWING. *2 : Typical value is measured by using thermally conductive grease of λ = 0.9[W/(m • K)]. *3 : If you use this value, Rth(f-a) should be measured just under the chips. *4 : Case temperature (TC’) measured point is just under the chips. Note 1. IE, VEC, trr & Qrr represent characteristics of the anti-parallel, emitter-collector free-wheel diode (FWDi). 2. Pulse width and repetition rate should be such that the device junction temperature (Tj) does not exceed Tjmax rating. 3. Junction temperature (Tj) should not increase beyond 150°C. 4. No short circuit capability is designed. Feb. 2009 2 MITSUBISHI IGBT MODULES CM150DU-24NFH HIGH POWER SWITCHING USE PERFORMANCE CURVES OUTPUT CHARACTERISTICS (TYPICAL) 300 COLLECTOR CURRENT IC (A) TRANSFER CHARACTERISTICS (TYPICAL) 300 COLLECTOR CURRENT IC (A) Tj = 25°C 250 200 150 100 50 0 VGE=20 (V) 14 13 15 12 VCE = 10V 250 200 150 100 50 0 11 10 9 8 0 2 4 6 8 10 Tj = 25°C Tj = 125°C 0 5 10 15 20 COLLECTOR-EMITTER VOLTAGE VCE (V) GATE-EMITTER VOLTAGE VGE (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat) (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat) (V) 9 VGE = 15V 8 Tj = 25°C Tj = 125°C 7 6 5 4 3 2 1 0 0 50 100 150 200 250 300 10 Tj = 25°C IC = 300A 8 6 IC = 150A 4 IC = 60A 2 0 6 8 10 12 14 16 18 20 COLLECTOR CURRENT IC (A) GATE-EMITTER VOLTAGE VGE (V) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) 103 EMITTER CURRENT IE (A) 7 5 3 2 CAPACITANCE CHARACTERISTICS (TYPICAL) 102 CAPACITANCE Cies, Coes, Cres (nF) 7 5 3 2 Tj = 125°C Tj = 25°C Cies 101 7 5 3 2 102 7 5 3 2 100 7 5 3 2 Coes Cres VGE = 0V 101 0 1 2 3 4 5 10–1 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 COLLECTOR-EMITTER VOLTAGE VCE (V) Feb. 2009 3 EMITTER-COLLECTOR VOLTAGE VEC (V) MITSUBISHI IGBT MODULES CM150DU-24NFH HIGH POWER SWITCHING USE HALF-BRIDGE SWITCHING TIME CHARACTERISTICS (TYPICAL) 103 7 5 SWITCHING TIME (ns) 3 2 5 3 2 5 3 td(off) td(on) tf tr Conditions: VCC = 600V VGE = ±15V RG = 2.1Ω Tj = 125°C Inductive load 23 5 7 103 102 7 5 3 2 Irr trr 2 102 7 5 3 2 102 7 101 7 5 3 2 100 1 10 2 3 5 7 102 101 1 10 2 3 5 7 102 Conditions: 5 VCC = 600V VGE = ±15V 3 RG = 2.1Ω 2 Tj = 25°C Inductive load 101 23 5 7 103 COLLECTOR CURRENT IC (A) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 100 EMITTER CURRENT IE (A) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi part) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 100 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth(j – c) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth(j – c) 7 5 3 2 Single Pulse TC = 25°C 10–1 7 5 3 2 7 5 3 2 Single Pulse TC = 25°C 10–1 7 5 3 2 10–1 7 5 3 2 10–1 7 5 3 2 10–2 7 5 3 Per unit base = 2 10–2 7 5 3 2 10–2 7 5 3 Per unit base = 2 10–2 7 5 3 2 Rth(j–c) = 0.19K/W 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 TIME (s) 10–3 Rth(j–c) = 0.35K/W 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 TIME (s) GATE CHARGE CHARACTERISTICS (TYPICAL) 20 GATE-EMITTER VOLTAGE VGE (V) IC = 150A VCC = 400V 15 VCC = 600V 10 5 0 0 200 400 600 800 1000 GATE CHARGE QG (nC) Feb. 2009 4 REVERSE RECOVERY CURRENT Irr (A) REVERSE RECOVERY TIME trr (ns) REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 103 103 Tj = 25°C 7 7