CM400DU-12F

MITSUBISHI IGBT MODULES CM400DU-12F HIGH POWER SWITCHING USE CM400DU-12F ¡IC ................................................................... 400A ¡VCES ............................................................ 600V ¡Insulated Type ¡2-elements in a pack APPLICATION General purpose inverters & Servo controls, etc OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm 108 93 ±0.25 14 14 Tc measured point 14 RTC E2 G2 6 C2E1 E2 RTC C1 48 ±0.25 CM G1 E1 6 CIRCUIT DIAGRAM C2E1 E2 C1 25 3-M6 NUTS 4-φ6. 5 MOUNTING HOLES 25 21.5 2.5 4 18 7 18 7 18 2.8 0.5 0.5 0.5 0.5 7.5 29 +1.0 –0.5 22 LABEL 8.5 4 Aug. 1999 G1 E1 15 62 E2 G2 MITSUBISHI IGBT MODULES CM400DU-12F HIGH POWER SWITCHING USE MAXIMUM RATINGS (Tj = 25°C) Symbol VCES VGES IC ICM IE ( Note 1) IEM ( Note 1) PC ( Note 3) Tj Tstg Viso — — Parameter Collector-emitter voltage Gate-emitter voltage Collector current Emitter current Maximum collector dissipation Junction temperature Storage temperature Isolation voltage Torque strength Weight G-E Short C-E Short TC = 25°C Pulse TC = 25°C Pulse TC = 25°C Conditions Ratings 600 ±20 400 800 400 800 960 –40 ~ +150 –40 ~ +125 2500 3.5 ~ 4.5 3.5 ~ 4.5 400 Unit V V A A W °C °C V N•m N•m g (Note 2) (Note 2) Main terminal to base plate, AC 1 min. Main Terminal M6 Mounting holes M6 Typical value ELECTRICAL CHARACTERISTICS (Tj = 25°C) Symbol ICES VGE(th) IGES VCE(sat) Cies Coes Cres QG td(on) tr td(off) tf trr ( Note 1) Qrr (Note 1) VEC(Note 1) Rth(j-c)Q Rth(j-c)R Rth(c-f) Rth(j-c’)Q RG Parameter Collector cutoff current Gate-emitter threshold voltage Gate leakage current Collector-emitter saturation voltage Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Turn-on delay time Turn-on rise time Turn-off delay time Turn-off fall time Reverse recovery time Reverse recovery charge Emitter-collector voltage Thermal resistance*1 Test conditions VCE = VCES, VGE = 0V IC = 40mA, VCE = 10V VGE = VCES, VCE = 0V Tj = 25°C IC = 400A, VGE = 15V Tj = 125 °C VCE = 10V VGE = 0V VCC = 300V, I C = 400A, VGE = 15V VCC = 300V, IC = 400A VGE1 = VGE2 = 15V RG = 3.1Ω, Inductive load switching operation IE = 400A IE = 400A, VGE = 0V IGBT part (1/2 module) FWDi part (1/2 module) Case to fin, Thermal compoundapplied*2 (1/2 module) Tc measured point is just under the chips Min. — 5 — — — — — — — — — — — — — — — — — — 3.1 Limits Typ. — 6 — 1.6 1.6 — — — 2480 — — — — — 7.7 — — — 0.04 — — Max. 1 7 40 2.2 — 110 7.2 4.0 — 400 200 700 250 200 — 2.6 0.13 0.18 — 0.076V3 31 Unit mA V µA V nF nC ns ns µC V °C/W Ω Contact thermal resistance Thermal resistance External gate resistance Note 1. IE, VEC, t rr, Q rr, die/dt represent characteristics of the anti-parallel, emitter to collector free-wheel diode. (FWDi). 2. Pulse width and repetition rate should be such that the device junction temp. (T j) does not exceed Tjmax rating. 3. Junction temperature (Tj) should not increase beyond 150°C. 4. Pulse width and repetition rate should be such as to cause negligible temperature rise. *1 : Tc measured point is indicated in OUTLINE DRAWING. *2 : Typical value is measured by using Shin-etsu Silicone “G-746”. *3 : If you use this value, Rth(f-a) should be measured just under the chips. Aug. 1999 MITSUBISHI IGBT MODULES CM400DU-12F HIGH POWER SWITCHING USE PERFORMANCE CURVES OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 800 700 Tj=25°C VGE=20V 9.5 15 11 10 3 VGE = 15V 2.5 2 1.5 1 0.5 0 Tj = 25°C Tj = 125°C 0 200 400 600 800 600 500 400 300 200 100 9 8.5 8 7.5 0 0 0.5 1 1.5 2 2.5 3 3.5 4 COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) 103 EMITTER CURRENT IE (A) 7 5 3 2 5 Tj = 25°C Tj = 25°C 4 3 IC = 800A IC = 400A IC = 160A 102 7 5 3 2 2 1 0 6 8 10 12 14 16 18 20 101 0 0.5 1 1.5 2 2.5 3 3.5 4 GATE-EMITTER VOLTAGE VGE (V) EMITTER-COLLECTOR VOLTAGE VEC (V) CAPACITANCE–VCE CHARACTERISTICS (TYPICAL) 103 CAPACITANCE Cies, Coes, Cres (nF) 7 5 3 2 HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) 103 7 5 3 2 td(off) td(on) tf 102 7 5 3 2 Cies SWITCHING TIMES (ns) 102 7 5 3 2 tr Conditions: VCC = 300V VGE = ±15V RG = 3.1Ω Tj = 125°C 101 7 5 3 2 101 7 5 3 2 VGE = 0V Cres Coes 100 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 COLLECTOR-EMITTER VOLTAGE VCE (V) 100 0 10 2 3 5 7101 2 3 5 7102 2 3 5 7103 COLLECTOR CURRENT IC (A) Aug. 1999 MITSUBISHI IGBT MODULES CM400DU-12F HIGH POWER SWITCHING USE REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) REVERSE RECOVERY TIME trr (ns) REVERSE RECOVERY CURRENT lrr (A) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j–c) (°C/W) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part & FWDi part) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 101 7 IGBT part: 5 Per unit base = Rth(j–c) = 0.13°C/W 3 FWDi part: 2 Per unit base = Rth(j–c) = 0.18°C/W 100 7 5 3 2 7 5 3 2 7 5 3 2 3 2 103 7 5 3 2 Conditions: VCC = 300V VGE = ±15V RG = 3.1Ω Tj = 25°C 102 1 7 5 3 2 Irr trr 10–1 10–1 7 5 3 2 7 5 3 2 10–2 Single Pulse TC = 25°C 10–2 101 1 10 2 3 5 7 102 2 3 5 7 103 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 TMIE (s) EMITTER CURRENT IE (A) GATE CHARGE CHARACTERISTICS (TYPICAL) 20 GATE-EMITTER VOLTAGE VGE (V) 18 16 14 12 10 8 6 4 2 0 0 IC = 400A VCC = 200V VCC = 300V 500 1000 1500 2000 2500 3000 3500 GATE CHARGE QG (nC) Aug. 1999