CM400DY-24NF

MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE CM400DY-24NF ¡IC ................................................................... 400A ¡VCES ......................................................... 1200V ¡Insulated Type ¡2-elements in a pack APPLICATION General purpose inverters & Servo controls, etc OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm Tc measured point (Base plate) 110 93±0.25 14 14 14 4 E2 G2 80 62±0.25 6 G1 E1 C2E1 E2 C1 3-M6 NUTS 25 25 21.5 4-φ6.5 MOUNTING HOLES 6 30 (20.5) 15 18 7 18 7 18 TAB #110. t=0.5 8.5 +1.0 –0.5 C2E1 E2 C1 CIRCUIT DIAGRAM G1 E1 29 LABEL 21.2 E2 G2 Mar.2003 MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE MAXIMUM RATINGS (Tj = 25°C) Symbol VCES VGES IC ICM IE (Note 1) IEM (Note 1) PC (Note 3) Tj Tstg Viso — — — Parameter Collector-emitter voltage Gate-emitter voltage Collector current Emitter current Maximum collector dissipation Junction temperature Storage temperature Isolation voltage Torque strength Weight G-E Short C-E Short DC, TC’ = 111°C*3 Pulse Pulse TC = 25°C Conditions Ratings 1200 ±20 400 800 400 800 1470 –40 ~ +150 –40 ~ +125 2500 3.5 ~ 4.5 3.5 ~ 4.5 580 Unit V V A A A A W °C °C V N•m N•m g (Note 2) (Note 2) Main Terminal to base plate, AC 1 min. Main Terminal M6 Mounting holes M6 Typical value ELECTRICAL CHARACTERISTICS (Tj = 25°C) Symbol ICES VGE(th) IGES VCE(sat) Cies Coes Cres QG td(on) tr td(off) tf trr (Note 1) Qrr (Note 1) VEC(Note 1) Rth(j-c)Q Rth(j-c)R Rth(c-f) Rth(j-c’)Q RG Parameter Collector cutoff current Gate-emitter threshold voltage Gate leakage current Collector-emitter saturation voltage Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Turn-on delay time Turn-on rise time Turn-off delay time Turn-off fall time Reverse recovery time Reverse recovery charge Emitter-collector voltage Thermal resistance*1 Contact thermal resistance Thermal resistance External gate resistance Test conditions VCE = VCES, VGE = 0V IC = 40mA, VCE = 10V VGE = VGES, VCE = 0V Tj = 25°C IC = 400A, VGE = 15V Tj = 125°C VCE = 10V VGE = 0V VCC = 600V, IC = 400A, VGE = 15V VCC = 600V, IC = 400A VGE1 = VGE2 = 15V RG = 0.73Ω, Inductive load switching operation IE = 400A IE = 400A, VGE = 0V IGBT part (1/2 module) FWDi part (1/2 module) Case to fin, Thermal compound Applied*2 (1/2 module) Tc measured point is just under the chips Min. — 6 — — — — — — — — — — — — — — — — — — 0.73 Limits Typ. — 7 — 1.8 2.0 — — — 2700 — — — — — 16 — — — 0.02 — — Max. 1 8 0.5 2.5 — 94 8 1.8 — 600 160 700 350 250 — 3.2 0.085 0.15 — 0.034*3 7.3 Unit mA V µA V nF nF nF nC ns ns ns ns ns µC V °C/W °C/W °C/W °C/W Ω *1 : Tc measured point is shown in page OUTLINE DRAWING. *2 : Typical value is measured by using Shin-etsu Silicone “G-746”. *3 : Tc’ measured point is just under the chips. If you use this value, Rth(f-a) should be measured just under the chips. Note 1. IE, VEC, trr & Qrr represent characteristics of the anti-parallel, emitter to collector free-wheel diode (FWDi). 2. Pulse width and repetition rate should be such that the device junction temp. (Tj) does not exceed Tjmax rating. 3. Junction temperature (Tj) should not increase beyond 150°C. Mar.2003 MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE PERFORMANCE CURVES OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 800 700 600 500 400 300 200 100 0 0 VGE = 20V 12 15 13 Tj = 25°C 4 VGE = 15V 3 11 2 10 9 2 4 6 8 10 1 Tj = 25°C Tj = 125°C 0 0 100 200 300 400 500 600 700 800 COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) 103 7 10 Tj = 25°C EMITTER CURRENT IE (A) 8 5 3 2 6 102 7 5 3 2 4 IC = 400A IC = 800A IC = 160A 2 Tj = 25°C Tj = 125°C 0 1 2 3 4 5 0 6 8 10 12 14 16 18 20 101 GATE-EMITTER VOLTAGE VGE (V) EMITTER-COLLECTOR VOLTAGE VEC (V) CAPACITANCE–VCE CHARACTERISTICS (TYPICAL) 103 CAPACITANCE Cies, Coes, Cres (nF) 7 5 3 2 7 5 3 2 7 5 3 2 7 5 3 2 HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) 104 7 5 3 2 102 Cies SWITCHING TIME (ns) 103 7 5 3 2 td(off) td(on) tf 101 Coes Cres 102 7 5 3 2 100 tr Conditions: VCC = 600V, VGE = ±15V, RG = 0.73Ω Tj = 125°C, Inductive load 2 3 5 7 102 2 3 5 7 103 VGE = 0V 10–1 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 COLLECTOR-EMITTER VOLTAGE VCE (V) 101 1 10 COLLECTOR CURRENT IC (A) Mar.2003 MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE REVERSE RECOVERY TIME trr (ns) REVERSE RECOVERY CURRENT lrr (A) REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 103 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j–c) 7 5 3 2 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part & FWDi part) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 100 7 5 3 2 Single Pulse TC = 25°C 10–1 7 5 3 2 Irr trr 10–1 7 5 3 2 102 7 5 3 2 101 1 10 2 3 5 7 102 Conditions: VCC = 600V VGE = ±15V RG = 0.73Ω Tj = 25°C Inductive load 23 5 7 103 IGBT part: 10–2 Per unit base = 7 5 Rth(j– c) = 0.085°C/W FWDi part: 3 Per unit base = 2 Rth(j– c) = 0.15°C/W –3 10 10–2 7 5 3 2 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 EMITTER CURRENT IE (A) TMIE (s) GATE CHARGE CHARACTERISTICS (TYPICAL) 20 GATE-EMITTER VOLTAGE VGE (V) IC = 400A 16 VCC = 400V VCC = 600V 12 8 4 0 0 500 1000 2000 3000 4000 1500 2500 3500 GATE CHARGE QG (nC) Mar.2003