CM50DY-28H

MITSUBISHI IGBT MODULES CM50DY-28H MEDIUM POWER SWITCHING USE INSULATED TYPE A B C F F K E2 G2 Q - DIA. (2 TYP.) D M G1 E1 J C2E1 E2 C1 N (3 TYP.) R S - M5 THD (3 TYP.) R R TAB#110 t=0.5 H L H P E G Description: Mitsubishi IGBT Modules are designed for use in switching applications. Each module consists of two IGBTs in a half-bridge configuration with each transistor having a reverse-connected super-fast recovery free-wheel diode. All components and interconnects are isolated from the heat sinking baseplate, offering simplified system assembly and thermal management. Features: Low Drive Power Low VCE(sat) Discrete Super-Fast Recovery Free-Wheel Diode High Frequency Operation Isolated Baseplate for Easy Heat Sinking Applications: AC Motor Control Motion/Servo Control UPS Welding Power Supplies Ordering Information: Example: Select the complete part module number you desire from the table below -i.e. CM50DY-28H is a 1400V-(VCES), 50 Ampere Dual IGBT Module. Type CM Current Rating Amperes 50 VCES Volts (x 50) 28 G2 E2 C2E1 E2 C1 E1 G1 Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J Inches 3.70 3.150±0.01 1.57 1.34 1.22 Max. 0.90 0.85 0.79 0.71 Millimeters 94.0 80.0±0.25 40.0 34.0 31.0 Max. 23.0 21.5 20.0 18.0 Dimensions K L M N P Q R S Inches 0.67 0.63 0.51 0.47 0.28 0.256 Dia. 0.16 M5 Metric Millimeters 17.0 16.0 13.0 12.0 7.0 Dia. 6.5 4.0 M5 Sep.1998 MITSUBISHI IGBT MODULES CM50DY-28H MEDIUM POWER SWITCHING USE INSULATED TYPE Absolute Maximum Ratings, Tj = 25 °C unless otherwise specified Ratings Junction Temperature Storage Temperature Collector-Emitter Voltage (G-E SHORT) Gate-Emitter Voltage (C-E SHORT) Collector Current (TC = 25°C) Peak Collector Current Emitter Current** (TC = 25°C) Peak Emitter Current** Maximum Collector Dissipation (TC = 25°C, Tj ≤ 150°C) Mounting Torque, M5 Main Terminal Mounting Torque, M6 Mounting Weight Isolation Voltage (Main Terminal to Baseplate, AC 1 min.) *Pulse width and repetition rate should be such that the device junction temperature (Tj) does not exceed Tj(max) rating. **Represents characteristics of the anti-parallel, emitter-to-collector free-wheel diode (FWDi). Symbol Tj Tstg VCES VGES IC ICM IE IEM Pc – – – Viso CM50DY-28H –40 to 150 –40 to 125 1400 ±20 50 100* 50 100* 400 1.47 ~ 1.96 1.96 ~ 2.94 190 2500 Units °C °C Volts Volts Amperes Amperes Amperes Amperes Watts N·m N·m Grams Vrms Static Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Collector-Cutoff Current Gate Leakage Current Gate-Emitter Threshold Voltage Collector-Emitter Saturation Voltage Symbol ICES IGES VGE(th) VCE(sat) QG VEC Test Conditions VCE = VCES, VGE = 0V VGE = VGES, VCE = 0V IC = 5mA, VCE = 10V IC = 50A, VGE = 15V IC = 50A, VGE = 15V, Tj = 150°C Total Gate Charge Emitter-Collector Voltage VCC = 800V, IC = 50A, VGE = 15V IE = 50A, VGE = 0V Min. – – 5.0 – – – – Typ. – – 6.5 3.1 2.95 255 – Max. 1.0 0.5 8.0 4.2** – – 3.8 Units mA µA Volts Volts Volts nC Volts ** Pulse width and repetition rate should be such that device junction temperature rise is negligible. Dynamic Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Input Capacitance Output Capacitance Reverse Transfer Capacitance Resistive Load Switching Times Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Symbol Cies Coes Cres td(on) tr td(off) tf trr Qrr IE = 50A, diE/dt = –100A/µs IE = 50A, diE/dt = –100A/µs VCC = 800V, IC = 50A, VGE1 = VGE2 = 15V, RG = 6.3Ω VGE = 0V, VCE = 10V Test Conditions Min. – – – – – – – – – Typ. – – – – – – – – 0.5 Max. 10 3.5 2.0 100 250 150 500 300 – Units nF nF nF ns ns ns ns ns µC Diode Reverse Recovery Time Diode Reverse Recovery Charge Thermal and Mechanical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Thermal Resistance, Junction to Case Thermal Resistance, Junction to Case Contact Thermal Resistance Symbol Rth(j-c) Rth(j-c) Rth(c-f) Test Conditions Per IGBT Per FWDi Per Module, Thermal Grease Applied Min. – – – Typ. – – – Max. 0.31 0.70 0.075 Units °C/W °C/W °C/W Sep.1998 MITSUBISHI IGBT MODULES CM50DY-28H MEDIUM POWER SWITCHING USE INSULATED TYPE OUTPUT CHARACTERISTICS (TYPICAL) TRANSFER CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 100 COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 80 15 Tj = 25oC VGE = 20V 100 13 12 VCE = 10V Tj = 25°C Tj = 125°C 5 VGE = 15V Tj = 25°C Tj = 125°C 80 4 11 60 60 3 40 10 40 2 20 7 9 8 20 0 1 0 0 2 4 6 8 10 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) 0 0 4 8 12 16 20 0 20 40 60 80 100 GATE-EMITTER VOLTAGE, VGE, (VOLTS) COLLECTOR-CURRENT, IC, (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE VS. VCE (TYPICAL) 10 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 102 Tj = 25°C Tj = 25°C EMITTER CURRENT, IE, (AMPERES) CAPACITANCE, Cies, Coes, Cres, (nF) 102 8 IC = 100A IC = 50A 101 Cies 6 101 100 Coes 4 2 10-1 VGE = 0V Cres IC = 20A 0 0 4 8 12 16 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 100 1.0 1.5 2.0 2.5 3.0 3.5 4.0 10-2 10-1 100 101 102 EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CURRENT, Irr, (AMPERES) GATE CHARGE, VGE 104 REVERSE RECOVERY TIME, t rr, (ns) 103 Irr 101 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) IC = 50A 103 SWITCHING TIME, (ns) td(off) tf 16 VCC = 600V VCC = 800V t rr 12 102 td(on) 102 100 8 101 tr VCC = 800V VGE = ±15V RG = 6.3Ω Tj = 125°C di/dt = -100A/µsec Tj = 25°C 4 100 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 101 100 101 EMITTER CURRENT, IE, (AMPERES) 10-1 102 0 0 100 200 300 400 GATE CHARGE, QG, (nC) Sep.1998 MITSUBISHI IGBT MODULES CM50DY-28H MEDIUM POWER SWITCHING USE INSULATED TYPE NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.31°C/W NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 10-3 10-2 10-1 100 101 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 10-3 10-2 10-1 100 101 101 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.7°C/W 10-1 10-1 10-1 10-1 10-2 10-2 10-2 10-2 10-3 10-5 TIME, (s) 10-4 10-3 10-3 10-3 10-5 TIME, (s) 10-4 10-3 10-3 Sep.1998