M30620MC-A18FP

Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Description The M16C/62M group of single-chip microcomputers are built using the high-performance silicon gate CMOS process using a M16C/60 Series CPU core and are packaged in a 100-pin plastic molded QFP. These single-chip microcomputers operate using sophisticated instructions featuring a high level of instruction efficiency. With 1M bytes of address space, low voltage (2.2V to 3.6V), they are capable of executing instructions at high speed. They also feature a built-in multiplier and DMAC, making them ideal for controlling office, communications, industrial equipment, and other high-speed processing applications. The M16C/62M group includes a wide range of products with different internal memory types and sizes and various package types. Features • Memory capacity .................................. ROM (See Figure 1.1.4. ROM Expansion) RAM 10K to 20K bytes • Shortest instruction execution time ...... 100ns (f(XIN)=10MHZ, VCC=2.7V to 3.6V) 142.9ns (f(XIN)=7MHZ, VCC=2.2V to 3.6V with software one-wait) • Supply voltage ..................................... 2.7V to 3.6V (f(XIN)=10MHZ, without software wait) 2.4V to 2.7V (f(XIN)=7MHZ, without software wait) 2.2V to 2.4V (f(XIN)=7MHZ with software one-wait) • Low power consumption ...................... 28.5mW (VCC = 3V, f(XIN)=10MHZ, without software wait) • Interrupts .............................................. 25 internal and 8 external interrupt sources, 4 software interrupt sources; 7 levels (including key input interrupt) • Multifunction 16-bit timer ...................... 5 output timers + 6 input timers • Serial I/O .............................................. 5 channels (3 for UART or clock synchronous, 2 for clock synchronous) • DMAC .................................................. 2 channels (trigger: 24 sources) • A-D converter ....................................... 10 bits X 8 channels (Expandable up to 10 channels) • D-A converter ....................................... 8 bits X 2 channels • CRC calculation circuit ......................... 1 circuit • Watchdog timer .................................... 1 line • Programmable I/O ............................... 87 lines _______ • Input port .............................................. 1 line (P85 shared with NMI pin) • Memory expansion .............................. Available (to a maximum of 1M bytes) • Chip select output ................................ 4 lines • Clock generating circuit ....................... 2 built-in clock generation circuits (built-in feedback resistor, and external ceramic or quartz oscillator) Applications Audio, cameras, office equipment, communications equipment, portable equipment 1 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Pin Configuration Figures 1.1.1 and 1.1.2 show the pin configurations (top view). PIN CONFIGURATION (top view) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P10/D8 P11/D9 P12/D10 P13/D11 P14/D12 P15/D13/INT3 P16/D14/INT4 P17/D15/INT5 P20/A0(/D0/-) P21/A1(/D1/D0) P22/A2(/D2/D1) P23/A3(/D3/D2) P24/A4(/D4/D3) P25/A5(/D5/D4) P26/A6(/D6/D5) P27/A7(/D7/D6) Vss P30/A8(/-/D7) Vcc P31/A9 P32/A10 P33/A11 P34/A12 P35/A13 P36/A14 P37/A15 P40/A16 P41/A17 P42/A18 P43/A19 P07/D7 P06/D6 P05/D5 P04/D4 P03/D3 P02/D2 P01/D1 P00/D0 P107/AN7/KI3 P106/AN6/KI2 P105/AN5/KI1 P104/AN4/KI0 P103/AN3 P102/AN2 P101/AN1 AVSS P100/AN0 VREF AVcc P97/ADTRG/SIN4 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 23 45 M16C/62 Group 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 P44/CS0 P45/CS1 P46/CS2 P47/CS3 P50/WRL/WR P51/WRH/BHE P52/RD P53/BCLK P54/HLDA P55/HOLD P56/ALE P57/RDY/CLKOUT P60/CTS0/RTS0 P61/CLK0 P62/RxD0 P63/TXD0 P64/CTS1/RTS1/CLKS1 P65/CLK1 P66/RxD1 P67/TXD1 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 P96/ANEX1/SOUT4 P95/ANEX0/CLK4 P94/DA1/TB4IN P93/DA0/TB3IN P92/TB2IN/SOUT3 P91/TB1IN/SIN3 P90/TB0IN/CLK3 BYTE CNVss P87/XCIN P86/XCOUT RESET XOUT VSS XIN VCC P85/NMI P84/INT2 P83/INT1 P82/INT0 P81/TA4IN/U P80/TA4OUT/U P77/TA3IN P76/TA3OUT P75/TA2IN/W P74/TA2OUT/W P73/CTS2/RTS2/TA1IN/V P72/CLK2/TA1OUT/V P71/RxD2/SCL/TA0IN/TB5IN P70/TXD2/SDA/TA0OUT Package: 100P6S-A Figure 1.1.1. Pin configuration (top view) 2 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER PIN CONFIGURATION (top view) P13/D11 P14/D12 P15/D13/INT3 P16/D14/INT4 P17/D15/INT5 P20/A0(/D0/-) P21/A1(/D1/D0) P22/A2(/D2/D1) P23/A3(/D3/D2) P24/A4(/D4/D3) P25/A5(/D5/D4) P26/A6(/D6/D5) P27/A7(/D7/D6) Vss P30/A8(/-/D7) Vcc P31/A9 P32/A10 P33/A11 P34/A12 P35/A13 P36/A14 P37/A15 P40/A16 P41/A17 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P12/D10 P11/D9 P10/D8 P07/D7 P06/D6 P05/D5 P04/D4 P03/D3 P02/D2 P01/D1 P00/D0 P107/AN7/KI3 P106/AN6/KI2 P105/AN5/KI1 P104/AN4/KI0 P103/AN3 P102/AN2 P101/AN1 AVSS P100/AN0 VREF AVcc P97/ADTRG/SIN4 P96/ANEX1/SOUT4 P95/ANEX0/CLK4 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 12 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 34567 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 M16C/62 Group P42/A18 P43/A19 P44/CS0 P45/CS1 P46/CS2 P47/CS3 P50/WRL/WR P51/WRH/BHE P52/RD P53/BCLK P54/HLDA P55/HOLD P56/ALE P57/RDY/CLKOUT P60/CTS0/RTS0 P61/CLK0 P62/RxD0 P63/TXD0 P64/CTS1/RTS1/CLKS1 P65/CLK1 P66/RxD1 P67/TXD1 P70/TXD2/SDA/TA0OUT P71/RxD2/SCL/TA0IN/TB5IN P72/CLK2/TA1OUT/V P94/DA1/TB4IN P93/DA0/TB3IN P92/TB2IN/SOUT3 P91/TB1IN/SIN3 P90/TB0IN/CLK3 BYTE CNVss P87/XCIN P86/XCOUT RESET XOUT VSS XIN VCC P85/NMI P84/INT2 P83/INT1 P82/INT0 P81/TA4IN/U P80/TA4OUT/U P77/TA3IN P76/TA3OUT P75/TA2IN/W P74/TA2OUT/W P73/CTS2/RTS2/TA1IN/V Package: 100P6Q-A Figure 1.1.2. Pin configuration (top view) 3 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Block Diagram Figure 1.1.3 is a block diagram of the M16C/62M group. Block diagram of the M16C/62M group 8 8 8 8 8 8 8 I/O ports Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6 Port P7 Internal peripheral functions Timer Timer TA0 (16 bits) Timer TA1 (16 bits) Timer TA2 (16 bits) Timer TA3 (16 bits) Timer TA4 (16 bits) Timer TB0 (16 bits) Timer TB1 (16 bits) Timer TB2 (16 bits) Timer TB3 (16 bits) Timer TB4 (16 bits) Timer TB5 (16 bits) A-D converter (10 bits X 8 channels Expandable up to 10 channels) System clock generator XIN-XOUT XCIN-XCOUT Clock synchronous SI/O 8 Port P8 UART/clock synchronous SI/O (8 bits X 3 channels) CRC arithmetic circuit (CCITT ) (Polynomial : X16+X12+X5+1) (8 bits X 2 channels) 7 Port P85 M16C/60 series16-bit CPU core Registers Program counter PC Vector table INTB Stack pointer ISP USP Flag register FLG R0H R0L R0H R0L R1H R1L R1H R1L R2 R2 R3 R3 A0 A0 A1 A1 FB FB SB Memory ROM (Note 1) RAM (Note 2) Watchdog timer (15 bits) Port P9 8 DMAC (2 channels) Port P10 D-A converter (8 bits X 2 channels) Multiplier 8 Note 1: ROM size depends on MCU type. Note 2: RAM size depends on MCU type. Figure 1.1.3. Block diagram of M16C/62M group 4 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Performance Outline Table 1.1.1 is a performance outline of M16C/62M group. Table 1.1.1. Performance outline of M16C/62M group Item Number of basic instructions Shortest instruction execution time Performance 91 instructions 100ns(f(XIN)=10MHZ, VCC=2.7V to 3.6V) 142.9ns (f(XIN)=7MHZ, VCC=2.2V to 3.6V with software one-wait) Memory ROM (See the figure 1.1.4. ROM Expansion) capacity RAM 10K to 20K bytes I/O port P0 to P10 (except P85) 8 bits x 10, 7 bits x 1 Input port P85 1 bit x 1 Multifunction TA0, TA1, TA2, TA3, TA4 16 bits x 5 timer TB0, TB1, TB2, TB3, TB4, TB5 16 bits x 6 Serial I/O UART0, UART1, UART2 (UART or clock synchronous) x 3 SI/O3, SI/O4 (Clock synchronous) x 2 A-D converter D-A converter DMAC CRC calculation circuit Watchdog timer Interrupt Clock generating circuit Supply voltage 10 bits x (8 + 2) channels 8 bits x 2 2 channels (trigger: 24 sources) CRC-CCITT 15 bits x 1 (with prescaler) 25 internal and 8 external sources, 4 software sources, 7 levels 2 built-in clock generation circuits (built-in feedback resistor, and external ceramic or quartz oscillator) 2.7V to 3.6V (f(XIN)=10MHZ, without software wait) 2.4V to 2.7V (f(XIN)=7MHZ, without software wait) 2.2V to 2.4V (f(XIN)=7MHZ with software one-wait) 28.5mW (f(XIN) =10MHZ, VCC=3V without software wait) 3V 1mA Available (to a maximum of 1M bytes) CMOS high performance silicon gate 100-pin plastic mold QFP Power consumption I/O I/O withstand voltage characteristics Output current Memory expansion Device configuration Package 5 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Mitsubishi plans to release the following products in the M16C/62M group: (1) Support for mask ROM version and Flash memory version (2) ROM capacity (3) Package 100P6S-A : Plastic molded QFP (mask ROM and flash memory versions) 100P6Q-A : Plastic molded QFP (mask ROM and flash memory versions) ROM Size (Byte) External ROM 256K 128K 96K 64K 32K Mask ROM version Flash memory version M30624MGM-XXXFP/GP M30620MCM-XXXFP/GP M30624FGMFP/GP M30620FCMFP/GP Figure 1.1.4. ROM expansion The M16C/62M group products currently supported are listed in Table 1.1.2. Table 1.1.2. M16C/62M group Type No M30620MCM-XXXFP M30620MCM-XXXGP M30624MGM-XXXFP M30624MGM-XXXGP M30620FCMFP M30620FCMGP M30624FGMFP M30624FGMGP 256K byte 20K byte 128K byte 10K byte 256K byte ROM capacity 128K byte RAM capacity 10K byte 20K byte Package type 100P6S-A 100P6Q-A 100P6S-A 100P6Q-A 100P6S-A 100P6Q-A 100P6S-A 100P6Q-A Flash memory 3V version mask ROM version June, 2000 Remarks 6 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Description SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Type No. M 3 0 6 2 0 M C M – X X X F P Package type: FP : Package GP : 100P6S-A 100P6Q-A ROM No. Omitted for blank flash memory version ROM capacity: C : 128K bytes G : 256K bytes Memory type: M : Mask ROM version F : Flash memory version Shows RAM capacity, pin count, etc (The value itself has no specific meaning) M16C/62 Group M16C Family Figure 1.1.5. Type No., memory size, and package 7 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Electrical characteristics SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Table 1.26.1. Absolute maximum ratings Symbol Vcc AVcc Supply voltage Analog supply voltage Input voltage VI RESET, CNVSS, BYTE, P00 to P07, P10 to P17, P20 to P27, P30 to P37,P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P87, P90 to P97, P100 to P107, VREF, XIN P70, P71 Output voltage VO P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P84, P86, P87, P90 to P97, P100 to P107, XOUT Ta=25 C Parameter Condition VCC=AVCC VCC=AVCC Rated value - 0.3 to 4.6 - 0.3 to 4.6 Unit V V - 0.3 to Vcc + 0.3 V - 0.3 to 4.6 V - 0.3 to Vcc + 0.3 V Pd P70, P71 Power dissipation - 0.3 to 4.6 300 - 20 to 85 / -40 to 85 (Note) - 65 to 150 Operating ambient temperature Topr Storage temperature Tstg Note : Specify a product of -40°C to 85°C to use it. V mW C C 8 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Electrical characteristics SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Table 1.26.2. Recommended operating conditions (referenced to VCC = 2.2V to 3.6V at Ta = – 20°C to 85oC / – 40°C to 85oC(Note3) unless otherwise specified) Symbol Vcc AVcc Vss AVss Parameter Supply voltage Analog supply voltage Supply voltage Analog supply voltage HIGH input voltage P31 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P87, P90 to P97, P100 to P107, XIN, RESET, CNVSS, BYTE P70, P71 P00 to P07, P10 to P17, P20 to P27, P30 (during single-chip mode) P00 to P07, P10 to P17, P20 to P27, P30 (data input function during memory expansion and microprocessor modes) Min. 2.2 Standard Typ. 3.0 Vcc 0 0 Max. 3.6 Unit V V V V 0.8Vcc 0.8Vcc 0.8Vcc 0.5Vcc 0 0 0 Vcc 4.6 Vcc Vcc 0.2Vcc 0.2Vcc 0.16Vcc - 10.0 V V V V V V V mA VIH LOW input voltage VIL P31 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97, P100 to P107, XIN, RESET, CNVSS, BYTE P00 to P07, P10 to P17, P20 to P27, P30 (during single-chip mode) P00 to P07, P10 to P17, P20 to P27, P30 (data input function during memory expansion and microprocessor modes) HIGH peak output I OH (peak) current I OH (avg) I OL (peak) I OL (avg) P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P84, P86, P87, P90 to P97, P100 to P107 HIGH average output P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, current P80 to P84, P86, P87, P90 to P97, P100 to P107 P00 to P07, P10 to P17, P20 to P27, P30 to P37, LOW peak output P40 to P47, P50 to P57, P60 to P67, P70 to P77, current P80 to P84, P86, P87, P90 to P97, P100 to P107 P00 to P07, P10 to P17, P20 to P27, P30 to P37, LOW average P40 to P47, P50 to P57, P60 to P67, P70 to P77, output current P80 to P84, P86, P87, P90 to P97, P100 to P107 Vcc=2.7V to 3.6V 0 0 0 0 0 32.768 - 5.0 mA 10.0 mA 5.0 10 10 X Vcc - 17 17.5 X Vcc - 35 10 6 X Vcc - 6.2 50 mA MHz MHz MHz MHz MHz kHz f (XIN) No wait Main clock input oscillation frequency Vcc=2.4V to 2.7V Vcc=2.2V to 2.4V Vcc=2.7V to 3.6V with wait Vcc=2.2V to 2.7V f (XcIN) Subclock oscillation frequency Note 1: The mean output current is the mean value within 100ms. Note 2: The total IOL (peak) for ports P0, P1, P2, P86, P87, P9, and P10 must be 80mA max. The total IOH (peak) for ports P0, P1, P2, P86, P87, P9, and P10 must be 80mA max. The total IOL (peak) for ports P3, P4, P5, P6, P7, and P80 to P84 must be 80mA max. The total IOH (peak) for ports P3, P4, P5, P6, P72 to P77, and P80 to P84 must be 80mA max. Note 3: Specify a product of -40°C to 85°C to use it. Note 4: Relationship between main clock oscillation frequency and supply voltage. Main clock input oscillation frequency (No wait) Main clock input oscillation frequency (With wait) Flash memory version program voltage and read operation voltage characteristics Operating maximum frequency [MHZ] 10.0 Operating maximum frequency [MHZ] 10 X VCC –17MHZ 10.0 6 X VCC –6.2MHZ Flash program voltage 7.0 Flash read operation voltage VCC=2.4V to 3.6V VCC=2.2V to 2.4V 7.0 17.5 X VCC –35MHZ VCC=2.7V to 3.6V VCC=2.7V to 3.4V 3.5 0.0 2.2 2.4 2.7 3.6 Supply voltage[V] 0.0 2.2 2.4 2.7 3.6 Supply voltage[V] (BCLK: no division) (BCLK: no division) Note 5: Execute case without wait, program / erase of flash memory by VCC=2.7V to 3.6V and f(BCLK) ≤ 6.25 MHz. Execute case with wait, program / erase of flash memory by VCC=2.7V to 3.6V and f(BCLK) ≤ 10.0 MHz. 9 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Electrical characteristics SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Table 1.26.3. Electrical characteristics (referenced to VCC = 2.7V to 3.6V, VSS = 0V at Ta = – 20oC to 85oC / – 40oC to 85oC (Note1), f(XIN) = 10MHZ without wait unless otherwise specified) Symbol VO H HIGH output voltage HIGH output voltage Parameter P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P84, P86,P87, P90 to P97, P100 to P107 XOUT XCOUT HIGHPOWER LOWPOWER HIGHPOWER LOWPOWER Measuring condition Min 2 .5 2 .5 2 .5 Standard Unit Typ. Max. V IOH=–1mA IOH=–0.1mA IOH=–50µA With no load applied With no load applied V 3 .0 1 .6 V VO H HIGH output voltage LOW output voltage VO L P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P84, P86,P87, P90 to P97, P100 to P107 XOUT HIGHPOWER LOWPOWER IOL=1mA IOL=0.1mA IOL=50µA With no load applied With no load applied 0 0 0 .5 0 .5 0 .5 V LOW output voltage V V VO L LOW output voltage Hysteresis XCOUT HIGHPOWER LOWPOWER VT+–VT– HOLD, RDY, TA0IN to TA4IN, TB0IN to TB5IN, INT0 to INT5, NMI, ADTRG, CTS0 to CTS2, SCL, SDA, CLK0 to CLK4, TA2OUT to TA4OUT, KI0 to KI3, RxD0 to RxD2, SIN3, SIN4 RESET P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97, P100 to P107, XIN, RESET, CNVss, BYTE P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97, P100 to P107, XIN, RESET, CNVss, BYTE P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P84, P86,P87, P90 to P97, P100 to P107 XIN XCIN When clock is stopped Mask ROM version In single-chip mode, the output pins are open and other pins are VSS Flash memory 3V version f(XIN)=10MHz Square wave, no division 0 .2 0 .8 V VT+–VT– II H Hysteresis HIGH input current 0 .2 1 .8 V VI=3V 4 .0 µA II L LOW input current VI=0V –4.0 µA RPULLUP RfXIN RfXCIN VRAM Pull-up resistance VI=0V 20 75 3 .0 10.0 330 kΩ MΩ MΩ V Feedback resistance Feedback resistance RAM retention voltage 2 .0 9 .5 21.25 mA f(XIN)=10MHz Square wave, no division 12.0 21.25 mA Mask ROM version, f(XCIN)=32kHz flash memory Square wave 3V version Flash memory 3V version program Flash memory 3V version erase 45.0 µA f(XIN)=10MHz Square wave, division by 2 14.0 mA f(XIN)=10MHz Square wave, division by 2 ICC Power supply current 17.0 mA Mask ROM version, f(XCIN)=32kHz When a WAIT instruction flash memory is executed. 3V version Oscillation capacity High (Note2) 2 .8 µA f(XCIN)=32kHz When a WAIT instruction is executed. Oscillation capacity Low (Note2) 0 .9 µA When clock is stopped Ta=25°C When clock is stopped Ta=85°C 1 .0 µA 20.0 Note 1: Specify a product of -40°C to 85°C to use it. Note 2: With one timer operated using fC32. 10 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Electrical characteristics SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Table 1.26.4. A-D conversion characteristics (referenced to VCC = AVCC = VREF = 2.4V to 3.6V, VSS = AVSS = 0V, at Ta = – 20oC to 85oC / – 40oC to 85oC (Note2), f(XIN)=10MHZ unless otherwise specified) Standard Symbol Parameter Measuring condition Unit Min. Typ. Max – – RLADDER tCONV VREF VI A Resolution Absolute accuracy Sample & hold function not available (8 bit) VREF =VCC VREF =VCC=3V, fAD=fAD/2 VREF =VCC 10 9.8 2.4 0 10 ±2 40 Bits LSB kΩ µs Ladder resistance Conversion time(8bit) Reference voltage Analog input voltage VCC VREF V V Note 1: Connect AVCC pin to VCC pin and apply the same electric potential. Note 2: Specify a product of –40°C to 85°C to use it. Table 1.26.5. D-A conversion characteristics (referenced to VCC = 2.4V to 3.6V, VSS = AVSS = 0V, VREF=3V, at Ta = – 20oC to 85oC / – 40oC to 85oC (Note2), f(XIN)=10MHZ unless otherwise specified) Symbol – – tsu RO IVREF Parameter Resolution Absolute accuracy Setup time Output resistance Reference power supply input current Measuring condition Standard Min. Typ. Max 8 1.0 3 4 10 20 1.0 Unit Bits % µs kΩ mA (Note1) Note 1: This applies when using one D-A converter, with the D-A register for the unused D-A converter set to “0016”. The A-D converter's ladder resistance is not included. Also, when DA register contents are not “00”, the current IVREF always flows even though Vref may have been set to be “unconnected” by the A-D control register. Note 2: Specify a product of –40°C to 85°C to use it. Table 1.26.6. Flash memory version electrical characteristics (referenced to VCC = 2.7V to 3.6V, at Ta =0oC to 60oC unless otherwise specified) Parameter Page program time Block erase time Erase all unlocked blocks time Lock bit program time Min. Standard Typ. 6 50 50 X n (Note) 6 Max 120 600 600 X n (Note) 120 Unit ms ms ms ms Note : n denotes the number of block erases. Table 1.26.7. Flash memory version program voltage and read operation voltage characteristics (Ta =0oC to 60oC) Flash program voltage VCC=2.7V to 3.6V VCC=2.7V to 3.4V Flash read operation voltage VCC=2.4V to 3.6V VCC=2.2V to 2.4V 11 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Timing requirements (referenced to VCC = 3V, VSS = 0V, at Ta = – 20oC to 85oC / – 40oC to 85oC (*) unless otherwise specified) * : Specify a product of -40°C to 85°C to use it. Table 1.26.8. External clock input Standard Symbol tc tw(H) tw(L) tr tf Parameter External clock input cycle time External clock input HIGH pulse width External clock input LOW pulse width External clock rise time External clock fall time Min. 100 40 40 Max. Unit ns ns ns 18 18 ns ns Table 1.26.9. Memory expansion and microprocessor modes Symbol tac1(RD-DB) tac2(RD-DB) tac3(RD-DB) tsu(DB-RD) tsu(RDY-BCLK ) tsu(HOLD-BCLK ) th(RD-DB) th(BCLK -RDY) th(BCLK-HOLD ) td(BCLK-HLDA) Parameter Data input access time (no wait) Data input access time (with wait) Data input access time (when accessing multiplex bus area) Data input setup time RDY input setup time HOLD input setup time Data input hold time RDY input hold time HOLD input hold time HLDA output delay time 10 9 – 90 f(BCLK) X 2 3 X 10 – 90 f(BCLK) X 2 3 X 10 9 – 90 f(BCLK) X 2 9 Standard Min. Max. (Note) (Note) (Note) 80 60 80 0 0 0 Unit ns ns ns ns ns ns ns ns ns 100 ns Note: Calculated according to the BCLK frequency as follows: tac1(RD – DB) = tac2(RD – DB) = tac3(RD – DB) = [ns] [ns] [ns] 12 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Timing requirements (referenced to VCC = 3V, VSS = 0V, at Ta = – 20oC to 85oC / – 40oC to 85oC (*) unless otherwise specified) * : Specify a product of –40°C to 85°C to use it. Table 1.26.10. Timer A input (counter input in event counter mode) Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. 150 60 60 Max. Unit ns ns ns Table 1.26.11. Timer A input (gating input in timer mode) Standard Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Min. 600 300 300 Max. Unit ns ns ns Table 1.26.12. Timer A input (external trigger input in one-shot timer mode) Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 300 150 150 Unit ns ns ns Table 1.26.13. Timer A input (external trigger input in pulse width modulation mode) Symbol tw(TAH) tw(TAL) TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 150 150 Unit ns ns Table 1.26.14. Timer A input (up/down input in event counter mode) Symbol tc(UP) tw(UPH) tw(UPL) tsu(UP-TIN) th(TIN-UP) TAiOUT input cycle time TAiOUT input HIGH pulse width TAiOUT input LOW pulse width TAiOUT input setup time TAiOUT input hold time Parameter Standard Min. Max. 3000 1500 1500 600 600 Unit ns ns ns ns ns 13 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Timing requirements (referenced to VCC = 3V, VSS = 0V, at Ta = – 20oC to 85oC / – 40oC to 85oC (*) unless otherwise specified) * : Specify a product of –40°C to 85°C to use it. Table 1.26.15. Timer B input (counter input in event counter mode) Symbol tc(TB) tw(TBH) tw(TBL) tc(TB) tw(TBH) tw(TBL) Parameter TBiIN input cycle time (counted on one edge) TBiIN input HIGH pulse width (counted on one edge) TBiIN input LOW pulse width (counted on one edge) TBiIN input cycle time (counted on both edges) TBiIN input HIGH pulse width (counted on both edges) TBiIN input LOW pulse width (counted on both edges) Min. Standard Max. Unit ns ns ns ns ns ns 150 60 60 300 160 160 Table 1.26.16. Timer B input (pulse period measurement mode) Symbol tc(TB) tw(TBH) tw(TBL) TBiIN input cycle time TBiIN input HIGH pulse width TBiIN input LOW pulse width Parameter Standard Min. 600 300 300 Max. ns ns ns Unit Table 1.26.17. Timer B input (pulse width measurement mode) Symbol tc(TB) tw(TBH) tw(TBL) TBiIN input cycle time TBiIN input HIGH pulse width TBiIN input LOW pulse width Parameter Standard Min. Max. 600 300 300 Unit ns ns ns Table 1.26.18. A-D trigger input Symbol tc(AD) tw(ADL) Parameter ADTRG input cycle time (trigger able minimum) ADTRG input LOW pulse width Standard Min. Max. 1500 200 Unit ns ns Table 1.26.19. Serial I/O Symbol tc(CK) tw(CKH) tw(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) CLKi input cycle time CLKi input HIGH pulse width CLKi input LOW pulse width TxDi output delay time TxDi hold time RxDi input setup time RxDi input hold time _______ Parameter Standard Min. 300 150 150 160 0 50 90 Max. Unit ns ns ns ns ns ns ns Table 1.26.20. External interrupt INTi inputs Symbol tw(INH) tw(INL) INTi input HIGH pulse width INTi input LOW pulse width Parameter Standard Min. 380 380 Max. Unit ns ns 14 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Switching characteristics (referenced to VCC = 3V, VSS = 0V at Ta = – 20oC to 85oC / – 40oC to 85oC (Note 3), CM15 = “1” unless otherwise specified) Table 1.26.21. Memory expansion and microprocessor modes (with no wait) Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) Parameter Address output delay time Address output hold time (BCLK standard) Address output hold time (RD standard) Address output hold time (WR standard) Chip select output delay time Chip select output hold time (BCLK standard) ALE signal output delay time ALE signal output hold time RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (BCLK standard) Data output hold time (BCLK standard) Data output delay time (WR standard) Data output hold time (WR standard)(Note2) Measuring condition Figure 1.26.1 Standard Min. Max. 60 4 0 0 60 4 60 —4 60 0 60 0 80 4 (Note1) 0 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note 1: Calculated according to the BCLK frequency as follows: td(DB – WR) = 10 9 f(BCLK) X 2 – 80 [ns] Note 2: This is standard value shows the timing when the output is off, and doesn't show hold time of data bus. Hold time of data bus is different by capacitor volume and pull-up (pull-down) resistance value. Hold time of data bus is expressed in t = –CR X ln (1 – VOL / VCC) by a circuit of the right figure. For example, when VOL = 0.2VCC, C = 30pF, R = 1kΩ, hold time of output “L” level is t = – 30pF X 1kΩ X ln (1 – 0.2VCC / VCC) = 6.7ns. Note 3: Specify a product of –40°C to 85°C to use it. R DBi C P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 30pF Figure 1.26.1. Port P0 to P10 measurement circuit 15 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Switching characteristics (referenced to VCC = 3V, VSS = 0V at Ta = – 20oC to 85oC / – 40oC to 85oC (Note 3), CM15 = “1” unless otherwise specified) Table 1.26.22. Memory expansion and microprocessor modes (when accessing external memory area with wait) Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) Parameter Address output delay time Address output hold time (BCLK standard) Address output hold time (RD standard) Address output hold time (WR standard) Chip select output delay time Chip select output hold time (BCLK standard) ALE signal output delay time ALE signal output hold time RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (BCLK standard) Data output hold time (BCLK standard) Data output delay time (WR standard) Data output hold time (WR standard)(Note2) Measuring condition Figure 1.26.1 Standard Min. Max. 60 4 0 0 60 4 60 –4 60 0 60 0 80 4 (Note1) 0 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note 1: Calculated according to the BCLK frequency as follows: td(DB – WR) = 10 f(BCLK) 9 – 80 [ns] Note 2: This is standard value shows the timing when the output is off, and doesn't show hold time of data bus. Hold time of data bus is different by capacitor volume and pull-up (pull-down) resistance value. Hold time of data bus is expressed in t = –CR X ln (1 – VOL / VCC) by a circuit of the right figure. For example, when VOL = 0.2VCC, C = 30pF, R = 1kΩ, hold time of output “L” level is t = – 30pF X 1kΩ X ln (1 – 0.2VCC / VCC) = 6.7ns. Note 3: Specify a product of –40°C to 85°C to use it. R DBi C 16 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Switching characteristics (referenced to VCC = 3V, VSS = 0V at Ta = – 20oC to 85oC / – 40oC to 85oC (Note 2), CM15 = “1” unless otherwise specified) Table 1.26.23. Memory expansion and microprocessor modes (when accessing external memory area with wait, and select multiplexed bus) Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) th(RD-CS) th(WR-CS) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) td(BCLK-ALE) th(BCLK-ALE) td(AD-ALE) th(ALE-AD) td(AD-RD) td(AD-WR) tdZ(RD-AD) Parameter Address output delay time Address output hold time (BCLK standard) Address output hold time (RD standard) Address output hold time (WR standard) Chip select output delay time Chip select output hold time (BCLK standard) Chip select output hold time (RD standard) Chip select output hold time (WR standard) RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (BCLK standard) Data output hold time (BCLK standard) Data output delay time (WR standard) Data output hold time (WR standard) ALE signal output delay time (BCLK standard) ALE signal output hold time (BCLK standard) ALE signal output delay time (Address standard) ALE signal output hold time(Address standard) Post-address RD signal output delay time Post-address WR signal output delay time Address output floating start time Measuring condition Figure 1.26.1 Standard Min. Max. 60 4 (Note 1) (Note 1) 60 4 (Note 1) (Note 1) 60 0 60 0 80 4 (Note 1) (Note 1) 60 –4 (Note 1) 40 0 0 8 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note 1: Calculated according to the BCLK frequency as follows: th(RD – AD) = 10 9 f(BCLK) X 2 th(WR – AD) = 10 9 [ns] f(BCLK) X 2 10 9 f(BCLK) X 2 [ns] th(RD – CS) = [ns] th(WR – CS) = 10 9 f(BCLK) X 2 10 9 [ns] td(DB – WR) = X3 – 80 f(BCLK) X 2 th(WR – DB) = 10 9 [ns] f(BCLK) X 2 10 9 [ns] – 45 td(AD – ALE) = f(BCLK) X 2 [ns] Note 2: Specify a product of –40°C to 85°C to use it. 17 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER VCC = 3V tc(TA) tw(TAH) TAiIN input tw(TAL) tc(UP) tw(UPH) TAiOUT input tw(UPL) TAiOUT input (Up/down input) During event counter mode TAiIN input (When count on falling edge is selected) TAiIN input (When count on rising edge is selected) th(TIN–UP) tsu(UP–TIN) tc(TB) tw(TBH) TBiIN input tw(TBL) tc(AD) tw(ADL) ADTRG input tc(CK) tw(CKH) CLKi tw(CKL) th(C–Q) TxDi td(C–Q) RxDi tw(INL) INTi input tw(INH) tsu(D–C) th(C–D) Figure 1.26.2. VCC=3V timing diagram (1) 18 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER VCC = 3V Memory Expansion Mode and Microprocessor Mode (Valid only with wait) BCLK RD (Separate bus) WR, WRL, WRH (Separate bus) RD (Multiplexed bus) WR, WRL, WRH (Multiplexed bus) RDY input tsu(RDY–BCLK) th(BCLK–RDY) (Valid with or without wait) BCLK tsu(HOLD–BCLK) HOLD input th(BCLK–HOLD) HLDA output td(BCLK–HLDA) P0, P1, P2, P3, P4, P50 to P52 Hi–Z td(BCLK–HLDA) Note: The above pins are set to high-impedance regardless of the input level of the BYTE pin and bit (PM06) of processor mode register 0 selects the function of ports P40 to P43. Measuring conditions : • VCC=3V • Input timing voltage : Determined with VIL=0.6V, VIH=2.4V • Output timing voltage : Determined with VOL=1.5V, VOH=1.5V Figure 1.26.3. VCC=3V timing diagram (2) 19 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER VCC = 3V Memory Expansion Mode and Microprocessor Mode (With no wait) Read timing BCLK td(BCLK–CS) 60ns.max th(BCLK–CS) 4ns.min CSi tcyc th(RD–CS) 0ns.min th(BCLK–AD) 4ns.min td(BCLK–AD) ADi BHE ALE RD 60ns.max td(BCLK–ALE) th(BCLK–ALE) 60ns.max –4ns.min th(RD–AD) 0ns.min th(BCLK–RD) 0ns.min td(BCLK–RD) 60ns.max tac1(RD–DB) DB Hi–Z th(RD–DB) tSU(DB–RD) 80ns.min 0ns.min Write timing BCLK td(BCLK–CS) 60ns.max th(BCLK–CS) 4ns.min CSi tcyc th(WR–CS) 0ns.min td(BCLK–AD) 60ns.max th(BCLK–AD) 4ns.min ADi BHE ALE td(BCLK–ALE) th(BCLK–ALE) 60ns.max –4ns.min th(WR–AD) 0ns.min WR,WRL, WRH DB td(BCLK–WR) 60ns.max td(BCLK–DB) 80ns.max Hi–Z th(BCLK–WR) 0ns.min th(BCLK–DB) 4ns.min td(DB–WR) (tcyc/2–80)ns.min th(WR–DB) 0ns.min Figure 1.26.4. VCC=3V timing diagram (3) 20 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Memory Expansion Mode and Microprocessor Mode (When accessing external memory area with wait) Read timing BCLK td(BCLK–CS) 60ns.max VCC = 3V th(BCLK–CS) 4ns.min CSi tcyc th(RD–CS) 0ns.min td(BCLK–AD) ADi BHE ALE td(BCLK–RD) 60ns.max 60ns.max th(BCLK–AD) 4ns.min td(BCLK–ALE) 60ns.max th(RD–AD) 0ns.min th(BCLK–ALE) –4ns.min th(BCLK–RD) 0ns.min RD tac2(RD–DB) DB Hi–Z th(RD–DB) tSU(DB–RD) 80ns.min 0ns.min Write timing BCLK td(BCLK–CS) 60ns.max th(BCLK–CS) 4ns.min CSi tcyc th(WR–CS) 0ns.min td(BCLK–AD) ADi BHE ALE td(BCLK–WR) WR,WRL, WRH td(BCLK–DB) 80ns.max 60ns.max 60ns.max th(BCLK–AD) 4ns.min td(BCLK–ALE) 60ns.max th(WR–AD) 0ns.min th(BCLK–ALE) –4ns.min th(BCLK–WR) 0ns.min th(BCLK–DB) 4ns.min DBi th(WR–DB) td(DB–WR) (tcyc–80)ns.min 0ns.min Measuring conditions : • VCC=3V • Input timing voltage : Determined with VIL=0.48V, VIH=1.5V • Output timing voltage : Determined with VOL=1.5V, VOH=1.5V Figure 1.26.5. VCC=3V timing diagram (4) 21 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Timing SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER VCC = 3V Memory Expansion Mode and Microprocessor Mode (When accessing external memory area with wait, and select multiplexed bus) Read timing BCLK td(BCLK–CS) 60ns.max tcyc th(BCLK–CS) th(RD–CS) (tcyc/2)ns.min 4ns.min CSi td(AD–ALE) (tcyc/2–45)ns.min ADi /DBi Address tdz(RD–AD) 8ns.max tac3(RD–DB) Data input Address th(ALE–AD) 40ns.min th(RD–DB) tSU(DB–RD) 80ns.min 0ns.min td(AD–RD) 0ns.min td(BCLK–AD) ADi BHE ALE RD 60ns.max th(BCLK–AD) 4ns.min td(BCLK–ALE) 60ns.max th(BCLK–ALE) –4ns.min th(RD–AD) (tcyc/2)ns.min th(BCLK–RD) 0ns.min td(BCLK–RD) 60ns.max Write timing BCLK td(BCLK–CS) 60ns.max tcyc th(BCLK–CS) th(WR–CS) (tcyc/2)ns.min 4ns.min CSi td(BCLK–DB) 80ns.max th(BCLK–DB) 4ns.min Data output Address ADi /DBi Address td(AD–ALE) (tcyc/2–60)ns.min td(BCLK–AD) ADi BHE ALE 60ns.max td(DB–WR) (tcyc*3/2–80)ns.min th(WR–DB) (tcyc/2)ns.min th(BCLK–AD) 4ns.min td(BCLK–ALE) th(BCLK–ALE) 60ns.max –4ns.min td(AD–WR) 0ns.min th(WR–AD) (tcyc/2)ns.min th(BCLK–WR) 0ns.min td(BCLK–WR) WR,WRL, WRH 60ns.max Measuring conditions : • VCC=3V • Input timing voltage : Determined with VIL=0.48V,VIH=1.5V • Output timing voltage : Determined with VOL=1.5V,VOH=1.5V Figure 1.26.6. VCC=3V timing diagram (5) 22 Mitsubishi microcomputers Usage precaution Usage Precaution Timer A (timer mode) M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER (1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the value of the counter. Reading the timer Ai register with the reload timing gets “FFFF16”. Reading the timer Ai register after setting a value in the timer Ai register with a count halted but before the counter starts counting gets a proper value. Timer A (event counter mode) (1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the value of the counter. Reading the timer Ai register with the reload timing gets “FFFF16” by underflow or “000016” by overflow. Reading the timer Ai register after setting a value in the timer Ai register with a count halted but before the counter starts counting gets a proper value. (2) When stop counting in free run type, set timer again. Timer A (one-shot timer mode) (1) Setting the count start flag to “0” while a count is in progress causes as follows: • The counter stops counting and a content of reload register is reloaded. • The TAiOUT pin outputs “L” level. • The interrupt request generated and the timer Ai interrupt request bit goes to “1”. (2) The timer Ai interrupt request bit goes to “1” if the timer's operation mode is set using any of the following procedures: • Selecting one-shot timer mode after reset. • Changing operation mode from timer mode to one-shot timer mode. • Changing operation mode from event counter mode to one-shot timer mode. Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0” after the above listed changes have been made. Timer A (pulse width modulation mode) (1) The timer Ai interrupt request bit becomes “1” if setting operation mode of the timer in compliance with any of the following procedures: • Selecting PWM mode after reset. • Changing operation mode from timer mode to PWM mode. • Changing operation mode from event counter mode to PWM mode. Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0” after the above listed changes have been made. (2) Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop counting. If the TAiOUT pin is outputting an “H” level in this instance, the output level goes to “L”, and the timer Ai interrupt request bit goes to “1”. If the TAiOUT pin is outputting an “L” level in this instance, the level does not change, and the timer Ai interrupt request bit does not becomes “1”. Timer B (timer mode, event counter mode) (1) Reading the timer Bi register while a count is in progress allows reading , with arbitrary timing, the value of the counter. Reading the timer Bi register with the reload timing gets “FFFF16”. Reading the timer Bi register after setting a value in the timer Bi register with a count halted but before the counter starts counting gets a proper value. 23 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Usage precaution SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Timer B (pulse period/pulse width measurement mode) (1) If changing the measurement mode select bit is set after a count is started, the timer Bi interrupt request bit goes to “1”. (2) When the first effective edge is input after a count is started, an indeterminate value is transferred to the reload register. At this time, timer Bi interrupt request is not generated. A-D Converter (1) Write to each bit (except bit 6) of A-D control register 0, to each bit of A-D control register 1, and to bit 0 of A-D control register 2 when A-D conversion is stopped (before a trigger occurs). In particular, when the Vref connection bit is changed from “0” to “1”, start A-D conversion after an elapse of 1 µs or longer. (2) When changing A-D operation mode, select analog input pin again. (3) Using one-shot mode or single sweep mode Read the correspondence A-D register after confirming A-D conversion is finished. (It is known by AD conversion interrupt request bit.) (4) Using repeat mode, repeat sweep mode 0 or repeat sweep mode 1 Use the undivided main clock as the internal CPU clock. Stop Mode and Wait Mode ____________ (1) When returning from stop mode by hardware reset, RESET pin must be set to “L” level until main clock oscillation is stabilized. (2) When switching to either wait mode or stop mode, instructions occupying four bytes either from the WAIT instruction or from the instruction that sets the every-clock stop bit to “1” within the instruction queue are prefetched and then the program stops. So put at least four NOPs in succession either to the WAIT instruction or to the instruction that sets the every-clock stop bit to “1”. Interrupts (1) Reading address 0000016 • When maskable interrupt is occurred, CPU read the interrupt information (the interrupt number and interrupt request level) in the interrupt sequence. The interrupt request bit of the certain interrupt written in address 0000016 will then be set to “0”. Reading address 0000016 by software sets enabled highest priority interrupt source request bit to “0”. Though the interrupt is generated, the interrupt routine may not be executed. Do not read address 0000016 by software. (2) Setting the stack pointer • The value of the stack pointer immediately after reset is initialized to 000016. Accepting an interrupt before setting a value in the stack pointer may become a factor of runaway. Be sure to set a value in the stack pointer before accepting an interrupt. _______ When using the NMI interrupt, initialize the stack point at the beginning of a program. Concerning _______ the first instruction immediately after reset, generating any interrupts including the NMI interrupt is prohibited. _______ (3) The NMI interrupt _______ _______ • The NMI interrupt can not be disabled. Be sure to connect NMI pin to Vcc via a pull-up resistor if unused. _______ • Do not get either into stop mode with the NMI pin set to “L”. 24 Mitsubishi microcomputers Usage precaution M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER (4) External interrupt _______ _______ • When the polarity of the INT0 to INT5 pins is changed, the interrupt request bit is sometimes set to "1". After changing the polarity, set the interrupt request bit to "0". (5) Rewrite the interrupt control register • To rewrite the interrupt control register, do so at a point that does not generate the interrupt request for that register. If there is possibility of the interrupt request occur, rewrite the interrupt control register after the interrupt is disabled. The program examples are described as follow: Example 1: INT_SWITCH1: FCLR I AND.B #00h, 0055h NOP NOP FSET I ; Disable interrupts. ; Clear TA0IC int. priority level and int. request bit. ; Four NOP instructions are required when using HOLD function. ; Enable interrupts. Example 2: INT_SWITCH2: FCLR I AND.B #00h, 0055h MOV.W MEM, R0 FSET I ; Disable interrupts. ; Clear TA0IC int. priority level and int. request bit. ; Dummy read. ; Enable interrupts. Example 3: INT_SWITCH3: PUSHC FLG FCLR I AND.B #00h, 0055h POPC FLG ; Push Flag register onto stack ; Disable interrupts. ; Clear TA0IC int. priority level and int. request bit. ; Enable interrupts. The reason why two NOP instructions (four when using the HOLD function) or dummy read are inserted before FSET I in Examples 1 and 2 is to prevent the interrupt enable flag I from being set before the interrupt control register is rewritten due to effects of the instruction queue. • When a instruction to rewrite the interrupt control register is executed but the interrupt is disabled, the interrupt request bit is not set sometimes even if the interrupt request for that register has been generated. This will depend on the instruction. If this creates problems, use the below instructions to change the register. Instructions : AND, OR, BCLR, BSET Noise (1) Insert bypass capacitor between VCC and VSS pin for noise and latch up countermeasure. • Insert bypass capacitor (about 0.1 µF) and connect short and wide line between VCC and VSS lines. 25 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) Usage precaution SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Notes on the microprocessor mode and transition after shifting from the microprocessor mode to the memory expansion mode • Microprocessor mode In microprocessor mode, the SFR, internal RAM, and external memory space can be accessed. For that reason, the internal ROM area cannot be accessed. • Memory expansion mode In memory expansion mode, external memory can be accessed in addition to the internal memory space (SFR, internal RAM, and internal ROM). However, after the reset has been released and the operation of shifting from the microprocessor mode has started (“H” applied to the CNVSS pin), the internal ROM area cannot be accessed even if the CPU shifts to the memory expansion mode. 26 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER GZZ-SH13-95B Mask ROM number Date : Note : Please complete all items marked g . ) Receipt MITSUBISHI ELECTRIC-CHIP 16-BIT MICROCOMPUTER M30620MCM-XXXFP/GP MASK ROM CONFIRMATION FORM Section head signature Supervisor signature g Customer Date issued g1. Check sheet Date : Mitsubishi processes the mask files generated by the mask file generation utilities out of those held on the floppy disks you give in to us, and forms them into masks. Hence, we assume liability provided that there is any discrepancy between the contents of these mask files and the ROM data to be burned into products we produce. Check thoroughly the contents of the mask files you give in. Prepare 3.5 inches 2HD (IBM format) floppy disks. And store only one mask file in a floppy disk. Microcomputer type No. : M30620MCM-XXXFP M30620MCM-XXXGP File code : (hex) Mask file name : .MSK (alpha-numeric 8-digit) g2. Mark specification The mark specification differs according to the type of package. After entering the mark specification on the separate mark specification sheet (for each package), attach that sheet to this masking check sheet for submission to Mitsubishi. For the M30620MCM-XXXFP, submit the 100P6S mark specification sheet. For the M30620MCM-XXXGP, submit the 100P6Q mark specification sheet. g3. Usage Conditions For our reference when of testing our products, please reply to the following questions about the usage of the products you ordered. (1) Which kind of XIN-XOUT oscillation circuit is used? Ceramic resonator External clock input What frequency do not use? f(XIN) = MHZ Quartz-crystal oscillator Other ( ) Issuance signature Company name TEL ( Submitted by Supervisor 27 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER GZZ-SH13-95B Mask ROM number MITSUBISHI ELECTRIC-CHIP 16-BIT MICROCOMPUTER M30620MCM-XXXFP/GP MASK ROM CONFIRMATION FORM (2) Which kind of XCIN-XCOUT oscillation circuit is used? Ceramic resonator External clock input What frequency do not use? f(XCIN) = kHZ Quartz-crystal oscillator Other ( ) (3) Which operation mode do you use? Single-chip mode Microprocessor mode (4) Which operating supply voltage do you use? (Circle the operating voltage range of use) 2.2 2.4 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 Memory expansion mode (V) (5) Which operating ambient temperature do you use? (Circle the operating temperature range of use) -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 (°C) (6) Do you use I2C (Inter IC) bus function? Not use Use (7) Do you use IE (Inter Equipment) bus function? Not use Use Thank you cooperation. g4. Special item (Indicate none if there is not specified item) 28 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER GZZ-SH13-48B Mask ROM number Date : Note : Please complete all items marked g . ) Receipt MITSUBISHI ELECTRIC-CHIP 16-BIT MICROCOMPUTER M30624MGM-XXXFP/GP MASK ROM CONFIRMATION FORM Section head signature Supervisor signature g Customer Date issued g1. Check sheet Date : Mitsubishi processes the mask files generated by the mask file generation utilities out of those held on the floppy disks you give in to us, and forms them into masks. Hence, we assume liability provided that there is any discrepancy between the contents of these mask files and the ROM data to be burned into products we produce. Check thoroughly the contents of the mask files you give in. Prepare 3.5 inches 2HD (IBM format) floppy disks. And store only one mask file in a floppy disk. Microcomputer type No. : M30624MGM-XXXFP M30624MGM-XXXGP File code : (hex) Mask file name : .MSK (alpha-numeric 8-digit) g2. Mark specification The mark specification differs according to the type of package. After entering the mark specification on the separate mark specification sheet (for each package), attach that sheet to this masking check sheet for submission to Mitsubishi. For the M30624MGM-XXXFP, submit the 100P6S mark specification sheet. For the M30624MGMXXXGP, submit the 100P6Q mark specification sheet. g3. Usage Conditions For our reference when of testing our products, please reply to the following questions about the usage of the products you ordered. (1) Which kind of XIN-XOUT oscillation circuit is used? Ceramic resonator External clock input What frequency do not use? f(XIN) = MHZ Quartz-crystal oscillator Other ( ) Issuance signature Company name TEL ( Submitted by Supervisor 29 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER GZZ-SH13-48B Mask ROM number MITSUBISHI ELECTRIC-CHIP 16-BIT MICROCOMPUTER M30624MGM-XXXFP/GP MASK ROM CONFIRMATION FORM (2) Which kind of XCIN-XCOUT oscillation circuit is used? Ceramic resonator External clock input What frequency do not use? f(XCIN) = kHZ Quartz-crystal oscillator Other ( ) (3) Which operation mode do you use? Single-chip mode Microprocessor mode (4) Which operating supply voltage do you use? (Circle the operating voltage range of use) 2.2 2.4 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 Memory expansion mode (V) (5) Which operating ambient temperature do you use? (Circle the operating temperature range of use) -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 (°C) (6) Do you use I2C (Inter IC) bus function? Not use Use (7) Do you use IE (Inter Equipment) bus function? Not use Use Thank you cooperation. g4. Special item (Indicate none if there is not specified item) 30 Mitsubishi microcomputers M16C / 62M Group (Low voltage version) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Differences between M16C/62M (Low voltage version) and M30624FGLFP/GP Item Memory area M16C/62M (Low voltage version) 1 Mbyte fixed M30624FGLFP/GP Memory expansion 1.2 Mbytes mode 4 Mbytes mode CTS/RTS separate function Serial I/O No CTS/RTS separate function IIC bus mode Analog or digital delay is selected as SDA delay Only analog delay is selected as SDA delay Memory version Mask ROM version Flash memory version Flash memory version only Standard serial I/O mode (Flash memory version) Clock synchronized Clock asynchronized Clock synchronized only 31 Keep safety first in your circuit designs! q Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials q q q q q q q q These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http:// www.mitsubishichips.com). When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semicon ductor product distributor for further details on these materials or the products con tained therein. MITSUBISHI SEMICONDUCTORS M16C/62M Group (Low voltage version) Specifications REV.B Jun. First Edition 2000 Edition by Committee of editing of Mitsubishi Semiconductor Published by Mitsubishi Electric Corp., Kitaitami Works This book, or parts thereof, may not be reproduced in any form without permission of Mitsubishi Electric Corporation. ©2000 MITSUBISHI ELECTRIC CORPORATION