MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
DESCRIPTION
The M37210M3-XXXSP/FP is a single-chip microcomputer designed with CMOS silicon gate technology. It is housed in a 52-pin shrink plastic molded DIP or a 64-pin plastic molded QFP. This single-chip microcomputer is useful for the channel selection system for TVs because it provides PWM function, OSD display function and so on. In addition to their simple instruction sets, the ROM, RAM, and I/O addresses are placed on the same memory map to enable easy programming. The features of the M37210E4-XXXSP/FP and the M37210E4SP/FP are similar to those of the M37210M4-XXXSP except that these chips have a built-in PROM which can be written electrically. The differences between the M37210M3-XXXSP/FP, the M37210 M4-XXXSP, and the M37211M2-XXXSP are the ROM size, the RAM size, and the PWM outputs as shown below. Accordingly, the following descriptions will be for the M37210M3-XXXSP/FP unless otherwise noted. Type name M37210M3-XXXSP/FP M37210M4-XXXSP M37211M2-XXXSP ROM size 12 K bytes 16 K bytes 8 K bytes RAM size 256 bytes 320 bytes 192 bytes 6-bit PWM outputs 8 8 6
PIN CONFIGURATION (TOP VIEW)
HSYNC → 1 VSYNC → 2 P60/PWM0 ← 3 P61/PWM1 ← 4 P62/PWM2 ← 5 P63/PWM3 ← 6 P00/PWM4 ↔ 7 P01/PWM5 ↔ 8 P02/PWM6 ↔ 9 P03/PWM7 ↔ 10 P42/SIN /A-D5 → 11 P41/SCLK ↔ 12 P40/SOUT (/IN ) ↔ 13 D-A ← 14 P35/INT2/A-D4 → 15 P34/INT1 → 16 P33/TIM3 → 17 P32/TIM2 → 18 P24 ↔ 19 P25 ↔ 20 P26 ↔ 21 P27 ↔ 22 CNVSS → 23 XIN → 24 XOUT ← 25 VSS
26 52 → P52/R 51 → P53/G 50 → P54/B 49 → P55/OUT 48 ↔ P20 47 ↔ P21 46 ↔ P22 45 ↔ P23 44 ↔ P04 43 ↔ P05 42 ↔ P06 41 ↔ P07 40 ↔ P10 39 ↔ P11 38 ↔ P12 37 ↔ P13 36 ↔ P14 35 ← P15/A-D1 34 ← P16/A-D2 33 ← P17/A-D3 32 ↔ P30 31 ↔ P31 30 ← RESET 29 ← OSC1 28 → OSC2 27
M37210M3-XXXSP M37210M4-XXXSP M37211M2-XXXSP
Note : After the reset, set the stack page selection bit which is set “1” to “0” because the internal RAM of the M37211M2-XXXSP is in only the zero page.
FEATURES
VCC
• Number of basic instructions ..................................................... 69 • Memory size ROM ................ 12 K bytes (M37210M3-XXXSP/FP)
16 K bytes (M37210M4-XXXSP) 8 K bytes (M37211M2-XXXSP) RAM ................. 256 bytes (M37210M3-XXXSP/FP) 320 bytes (M37210M4-XXXSP) 192 bytes (M37211M2-XXXSP) ROM for display......................................... 3 K bytes RAM for display .......................................... 72 bytes The minimum instruction execution time ........................................... 0.5µs (at 8MHz oscillation frequency) Power source voltage ..................................................... 5V ± 10% Power dissipation .............................................................. 110mW (at 4MHz oscillation frequency, VCC = 5.5V, at CRT display) Subroutine nesting ............................................... 96 levels (Max.) Interrupts ....................................................... 12 types, 12 vectors 8-bit timers .................................................................................. 4 Programmable I/O ports (Ports P0, P1, P2, P3, P4) ......................................................... 25 Output ports (ports P5, P6) .......................................................... 8 Output ports (ports P52, P5 6) ..................................................... 12 12 V withstand ports ....................................................................4 Serial I/O ............................................................ 8-bit ! 1 channel PWM output circuit ............... (14-bit ! 1, 6-bit ! 8) ... M37210M3 M37210M4 (14-bit ! 1, 6-bit ! 6) .... M37211M2
Outline 52P4B
Note : The M37211M2-XXXSP does not have the PWM6 and the PWM7.
• • • • • • • • • • • •
• A-D comparator (5-bit resolution) ................................ 5 channels • CRT display function
Display characters ..................................... 18 characters ! 2 lines (16 lines max.) Character kinds ................................................................ 96 kinds Dot structure ............................................................. 12 ! 16 dots Character size .................................................................... 3 kinds Character color kinds (It can be specified by the character) max. 7 kinds (R, G, B) Raster color (max. 7 kinds) Display layout Horizontal ..................................................................... 64 levels Vertical ....................................................................... 128 levels Bordering (horizontal and vertical)
APPLICATION
TV
1
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
PIN CONFIGURATION (TOP VIEW)
P22 P23 P04 P05 P06 P07 P10 NC P11 P12 P13 P14 NC P15/A-D1 P16/A-D2 P17/A-D3
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
P21 NC P20 P55 /OUT P54 / B P53 /G P52 /R NC NC HSYNC VSYNC P60 /PWM0 P61 /PWM1 P62 /PWM2 NC P63 /PWM3
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9
32 31 30 29 28 27 26 25
M37210M3-XXXFP
24 23 22 21 20 19 18 17
P30 NC P31 RESET OSC1 OSC2 Vcc NC NC VSS XOUT XIN CNVSS P27 NC NC
P00/PWM4 P01/PWM5 P02/PWM6 P03/PWM7 NC P42/SIN/A-D5 P41/SCLK P40/SOUT/(/IN) D-A P35/INT2/A-D4 P34/INT1 P33/TIM3 P32/TIM2 P24 P25 P26
Outline 64P6N-A
NC : No connection
2
FUNCTIONAL BLOCK DIAGRAM of M37210M3-XXXSP
(5V) (0V) (0V) VCC VSS CNVSS D-A
14 1 2 29 28
Clock input XIN HSYNC YSYNC OSC1 OSC2
30 27 26 23
Clock output XOUT
Reset input RESET
24
25
Clock generating circuit
Data bus Timer count source selection circuit 14-bit PWM circuit
Program counter PCH(8) Program counter PCL(8) ROM 12 K bytes (Note 3)
RAM 256bytes (Note 2)
Timer 1 T1 (8) 6-bit PWM circuit
PWM7
PWM6
PWM5
PWM4 PWM3
PWM2
PWM1
TIM2 Timer 3 T3 (8) TIM3 Timer 4 T4 (8)
Control signal
Instruction decoder
8-bit arithmetic and logical unit Index register X (8) Index register Y (8) Stack pointer (8)
Accumulator A(8)
Processor status register PS(8)
PWM0
Address bus
Timer 2 T2 (8)
Instruction register
CRT circuit
A-D comparator
INT1
Interrupt interval determination circuit
INT2
SI/O(8)
SIN
P0(8) 5 3
22 21 20 19 45 46 47 48
A-D4
P1(8)
P2(8)
P3(6)
SCLK SOUT
INT1, INT2
P4(3)
P6(4)
OUT
P5(4)
B G A-D5 R
A-D1
A-D2
41 42 43 44 10 9
8
7
33 34 35 36 37 38 39 40
A-D3
15 16 17 18 31 32
11 12 13
6
5
4
3
49 50 51 52
I/O port P0
I/O port P1
I/O port P2
I/O port P3
I/O port P4
Output port P6
Video signal output
Notes 1 : The M37211M2-XXXSP does not have PWM outputs of pins 9 and 10. 2 : 320 bytes for M37210M4-XXXSP and 192 bytes for M37211M2-XXXSP 3 : 16 K bytes for M37210M4-XXXSP and 8 K bytes for M37211M2-XXXSP
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
MITSUBISHI MICROCOMPUTERS
3
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
FUNCTIONS
Parameter Number of basic instructions Instruction execution time Clock frequency M37210M3-XXXSP/FP Memory size M37210M4-XXXSP M37211M2-XXXSP P0 P10 – P14 P15 – P17 P2 P30, P31 P32, P35 P40, P41 P42 P5 P6 ROM RAM ROM RAM ROM RAM I/O I/O Input I/O I/O Input I/O Input Output Output Functions 69 0.5µs (the minimum instruction execution time, at 8MHz oscillation frequency) 8MHz 12 K bytes 256 bytes 16 K bytes 320 bytes 8 K bytes 192 bytes 8-bit ! 1 (can be used as N-channel open-drain output and PWM4-PWM7)(Note) 5-bit ! 1 (CMOS 3-state output) 3-bit ! 1 (can be used as A-D input) 8-bit ! 1 (CMOS 3-state output) 2-bit ! 1 (CMOS 3-state input/output) 4-bit ! 1 (can be used as timer input pins, INT input pins and A-D input pins) 2-bit ! 1 (can be used as N-channel open-drain output and serial I/O function pins) 1-bit ! 1 (can be used as serial I/O and A-D input) 4-bit ! 1 (can be used as R, G, B, OUT pins) 4-bit ! 1 (can be used as N-channel open-drain output and PWM0-PWM3 output pins) 8-bit ! 1 8-bit timer ! 4 96 levels (max.) Two external interrupts, four internal timer interrupts, one serial I/O interrupt, one CRT interrupt, one f(XIN)/4096 interrupt, one VSYNC interrupt, BRK instruction Built-in circuit (externally connected a ceramic resonator or a quartz-crystal oscillator) 5V ± 10% 110mW (at 4MHz oscillation frequency, V CC = 5.5V, Typ.) 55mW (at 4MHz oscillation frequency, V CC = 5.5V, Typ.) 1.65mW (Max.) −10 to 70°C CMOS silicon gate process 52-pin shrink plastic molded DIP 64-pin plastic molded QFP 18 characters ! 2 lines : maximum 16 lines (by software) 12 ! 16 dots 96 kinds 3 kinds 7 kinds max, (R, G, B) : can be specified by character unit 64 levels (horizontal) ! 128 levels (vertical)
Input/Output ports
Serial I/O Timers Subroutine nesting Interrupt Clock generating circuit Power source voltage Power dissipation Operating temperature range Device structure Package M37210M3-XXXSP, M37210M4-XXXSP, M37211M2-XXXSP M37210M3-XXXFP Number of character Character dot construction Kinds of characters Character size Kinds of color Display position (horizontal, vertical) at CRT display ON at CRT display OFF at stop mode
CRT display function
Note : The M37211M2-XXXSP can be also used as PWM4 and PWM5.
4
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
PIN DESCRIPTION
Pin VCC , VSS CNVSS RESET Name Power source voltage CNVSS Reset input Input / Output Functions Apply voltage of 5V ± 10% to VCC , and 0V to VSS. This is connected to VSS . To enter the reset state, the reset input pin must be kept at a “L” for 2 µs or more (under normal VCC conditions). If more time is needed for the crystal oscillator to stabilize, this “L” condition should be maintained for the required time. This chip has an internal clock generating circuit. To control generating frequency, an external ceramic resonator or a quartz-crystal oscillator is connected between the XIN and XOUT pins. If an external clock is used, the clock source should be connected the XIN pin and the XOUT pin should be left open. This is the timing output pin. Port P0 is an 8-bit I/O port with directional registers allowing each I/O bit to be individually programmed as input or output. At reset, this port is set to input mode. The output structure is CMOS output. The output structure is N-channel open-drain output. When PWM4, PWM5, PWM6 and PWM7 are used, P00, P0 1, P02 and P03 are in common with PWM output pins of PWM4, PWM5, PWM6 and PWM7. Ports P10, P11 , P12, P13 and P14 are 5-bit I/O ports and have basically the same functions as port P0. The output structure is CMOS output. Ports P15, P16 and P17 are 3-bit input ports and they are in common with input pins of A-D comparator (A-D1, A-D2 and A-D3). Port P2 is an 8-bit I/O port and has basically the same functions as port P0. The output structure is CMOS output. Ports P30 and P3 1 are 2-bit I/O ports and have basically the same functions as port P0. The output structure is CMOS output. Ports P3 2, P33, P34 and P35 are 4-bit input ports and ports P32 and P33 are in common with external clock input pins of timers 2 and 3. Ports P3 4 and P3 5 are in common with external interrupt input pins INT1 and INT2. Port P35 is in common with an input pin of A-D comparator (A-D4). Ports P40 and P4 1 are 2-bit I/O ports and have basically the same functions as port P0. When serial I/O is used, ports P40 and P41 are in common with SOUT pin and SCLK pin, respectively. Port P42 is an 1-bit Input port, and it is common with an input pin of A-D comparator (A-D5) and serial input pin (SIN). Port P6 is an 4-bit output port. The output structure is N-channel open-drain. This port is in common with 6-bit PWM output pins PWM0-PWM3. This is the I/O pins of the clock generating circuit for the CRT display function.
Input
XIN XOUT φ P00 – P07
Clock input Clock output Timing output I/O port P0
Input Output Output I/O
P11 – P14 P15 – P17 P20 – P27 P30, P31 P32 – P35
I/O port P1 Input port P1 I/O port P2 I/O port P3 Input port P3
I/O Input I/O I/O Input
P40, P41
I/O port P4
I/O
P42 P60 – P63 OSC1, OSC2
Input port P4 Output port P6 Clock input for CRT display Clock output for CRT display HSYNC input VSYNC input CRT output DA Output
Input Output Input Output
HSYNC VSYNC R, G, B, OUT D-A
Input Input Output Output
This is the horizontal synchronizing signal input for CRT display. This is the vertical synchronizing signal input for CRT display. This is a 4-bit output pin for CRT display. The output structure is CMOS output. This is in common with port P52 – P55. This is an output pin for 14-bit PWM.
5
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
FUNCTIONAL DESCRIPTION Central Processing Unit (CPU)
The M37210M3-XXXSP/FP uses the standard 740 family instruction set. Refer to the table of 740 family addressing modes and machine instructions or the SERIES 740 〈 Software 〉 User’s Manual for details on the instruction set. Machine-resident 740 family instructions are as follows : The FST and SLW instruction cannot be used. The MUL, DIV, WIT, and STP instruction can be used.
CPU Mode Register
The CPU mode register is allocated at address 00FB16. The CPU mode register contains the stack page selection bit.
7 11111
0 00
CPU mode register (CPUM : address 00FB16) Fix these bits to “002” Stack page selection bit (Note) 0 : Zero page 1 : 1 page Fix these bits to “11112”
Note : Please beware of this bit when programming because it is set to “1” after the reset release. Especially the internal RAM of the M37211M2-XXXSP is in the zero page, so be sure to set this bit to “0”.
Fig. 1 Structure of CPU mode register
6
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
MEMORY Special Function Register (SFR) Area
The special function register (SFR) area in the zero page contains control registers such as I/O ports and timers.
Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
Zero Page
The 256 bytes from addresses 000016 to 00FF 16 are called the zero page area. The internal RAM and the special function registers (SFR) are allocated to this area. The zero page addressing mode can be used to specify memory and register addresses in the zero page area. Access to this area with only 2 bytes is possible in the zero page addressing mode.
RAM
RAM is used for data storage and for stack area of subroutine calls and interrupts.
ROM
ROM is used for sroring user programs as well as the interrupt vector area.
Special Page
The 256 bytes from addresses FF0016 to FFFF16 are called the special page area. The special page addressing mode can be used to specify memory addresses in the special page area. Access to this area with only 2 bytes is possible in the special page addressing mode.
RAM for Display
RAM for display is used for specifing the character codes and colors to display.
ROM for Display
ROM for display is used for storing character data.
RAM (192 bytes) for RAM M37211M2 (256 bytes) for M37210M3 000016 00BF16 SFR area 00FF16
RAM (320 bytes) for M37210M4
Zero page
013F16 017F16 Not used
200016 RAM for display (Note) (72 bytes) 20B116 ROM for display (3 K bytes) ROM (16 K bytes) ROM (12 K bytes) for M37210M4 for M37210M3 300016 35FF16
Not used
Not used 380016 3DFF16 Not used C00016
D00016 E00016 ROM (8 K bytes) FF0016 for M37211M2 FFDE16 FFFF16
Interrupt vector area
Special page
Note : Refer to Table 6. Contents of CRT display RAM
Fig. 2 Memory map
7
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
00C016 00C116 00C216 00C316 00C416 00C516 00C616 00C716 00C816 00C916 00CA16 00CB16 00CC16 00CD16 00CE16 00CF16 00D016 00D116 00D216 00D316 00D416 00D516 00D616 00D716 00D816 00D916 00DA16 00DB16 00DC16 00DD16 00DE16 00DF16
Port P0 Port P0 directional register Port P1 Port P1 directional register Port P2 Port P2 directional register Port P3 Port P3 directional register Port P4 Port P4 directional register Port P5 Port P5 control register Port P6 Port P6 directional register 14DA-H register 14DA-L register PWM0 register PWM1 register PWM2 register PWM3 register PWM4 register PWM output control register 1 PWM output control register 2 Interrupt Interval determination register Interrupt Interval determination control register
Serial I/O mode register Serial I/O register
00E016 00E116 00E216 00E316 00E416 00E516 00E616 00E716 00E816 00E916 00EA16 00EB16 00EC16 00ED16 00EE16 00EF16 00F016 00F116 00F216 00F316 00F416 00F516 00F616 00F716 00F816 00F916 00FA16 00FB16 00FC16 00FD16 00FE16 00FF16
Horizontal position register Vertical position register 1 (block 1) Vertical position register 2 (block 2) Character size register Border selection register Color register 0 Color register 1 Color register 2 Color register 3 CRT control register CRT port control register A-D mode register A-D control register Timer 1 Timer 2 Timer 3 Timer 4 Timer 12 mode register Timer 34 mode register PWM5 register PWM6 register (Note) PWM7 register (Note)
CPU mode register Interrupt request register 1 Interrupt request register 2 Interrupt control register1 Interrupt control register2
Note : The M37211M2-XXXSP dose not have this register
Fig. 3 Memory map of special function register (SFR )
8
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
INTERRUPTS
Interrupts can be caused by 12 different sources consisting of 3 external, 7 internal, 1 software, and reset. Interrupts are vectored interrupts with priorities shown in Table 1. Reset is also included in the table because its operation is similar to an interrupt. When an interrupt is accepted, the registers are pushed, interrupt disable flag I is set, and the program jumps to the address specified in the vector table. The interrupt request bit is cleared automatically. The reset can never be disabled. Other interrupts are disabled when the interrupt disable flag is set.
All interrupts except the BRK instruction interrupt have an interrupt request bit and an interrupt enable bit. The interrupt request bits are in interrupt request registers 1 and 2 and the interrupt enable bits are in interrupt control registers 1 and 2. Figure 4 shows the structure of the interrupt request registers 1 and 2 and interrupt control registers 1 and 2. Interrupts other than the BRK instruction interrupt and reset are accepted when the interrupt enable bit is “1”, interrupt request bit is “1”, and the interrupt disable flag is “0”. The interrupt request bit can be reset with a program, but not set. The interrupt enable bit can be set and reset with a program. Reset is treated as a non-maskable interrupt with the highest priority. Figure 5 shows interrupts control.
Table 1. Interrupt vector addresses and priority Interrupt sources Reset CRT interrupt INT2 interrupt INT1 interrupt Timer 4 interrupt f(XIN)/4096 interrupt VSYNC interrupt Timer 3 interrupt Timer 2 interrupt Timer 1 interrupt Serial I/O interrupt BRK instruction interrupt Priority 1 2 3 4 5 6 7 8 9 10 11 12 Vector addresses FFFF16, FFFE16 FFFD16, FFFB16, FFF916, FFF516, FFF316, FFF116, FFEF16, FFED16, FFEB16, FFE916, FFDF16, FFFC16 FFFA16 FFF816 FFF416 FFF216 FFF016 FFEE16 FFEC16 FFEA16 FFE816 FFDE16 Remarks Non-maskable Active edge selectable Active edge selectable
Active edge selectable
Non-maskable software interrupt
9
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
7
0 Interrupt request register 1 (IREQ1 : address 00FC16) Timer 1 interrupt request bit Timer 2 interrupt request bit Timer 3 interrupt request bit Timer 4 interrupt request bit CRT interrupt request bit VSYNC interrupt request bit
7 0
0 Interrupt request register 2 (IREQ2 : address 00FD16) INT1 interrupt request bit INT2 interrupt request bit Serial I/O1 interrupt request bit f(XIN)/4096 interrupt request bit Fix this bit to “0” 0 : No interrupt request issued 1 : Interrupt request issued
7 00
0 Interrupt control register 1 (ICON1 : address 00FE16) Timer 1 interrupt enable bit Timer 2 interrupt enable bit Timer 3 interrupt enable bit Timer 4 interrupt enable bit CRT interrupt enable bit VSYNC interrupt enable bit Fix these bits to “0”
7 000
0 Interrupt control register 2 (ICON2 : address 00FF16) INT1 interrupt enable bit INT2 interrupt enable bit Serial I/O1 interrupt enable bit Fix this bit to “0” f(XIN)/4096 interrupt enable bit Fix these bits to “0” 0 : Interrupt disabled 1 : Interrupt enabled
Fig. 4 Structure of interrupt-related registers
Interrupt request bit Interrupt enable bit Interrupt disable flag (I) BRK instruction reset interrupt request
Fig. 5 Interrupt control
10
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
TIMERS
The M37210M3-XXXSP has 4 timers: timer 1, timer 2, timer 3 and timer 4. All timers are 8-bit timers with the 8-bit timer latch. The timer block diagram is shown in Figure 7. All of the timers count down and their divide ratio is 1/(n+1), where n is the value of timer latch. The value is set to a timer at the same time by writing a count value to the corresponding timer latch (addresses 00F016 to 00F316 : timers 1 to 4). The count value is decremented by 1. The timer interrupt request bit is set to “1” by an timer overflow at the next count pulse after the count value reaches “0016.”
set bit 0 of the timer 34 mode register (address 00F516 ) to “0” before the execution of the STP instruction (f(XIN)16 is selected as the timer 3 count source). The internal STP state is released by timer 4 overflow at these state, the internal clock is connected . Because of this, the program starts with stable clock. The structure of timer-related registers is shown in Figure 6.
7
0 Timer 12 mode register (TM12MR : address 00F416 ) Timer 1 count source selection bit 0 : f (XIN ) /16 1 : 1024µs clock Timer 2 count source selection bit 0 : Internal clock source 1 : External clock source from P32 /TIM2 pin Timer 1 count stop bit 0 : Operation 1 : Stop Timer 2 count stop bit 0 : Operation 1 : stop Timer 2 internal count source selection bit 0 : f (XIN ) /16 1 : Timer 1 overflow signal Fix this bit to “0”
(1) Timer 1
Timer 1 can select one of the following count sources: f(XIN)/16 f(XIN)/4096 The count source of timer 1 is selected by setting bit 0 of the timer 12 mode register (address 00F416 ). Timer 1 interrupt request occurs at timer 1 overflow.
• •
(2) Timer 2
Timer 2 can select one of the following count sources: f(XIN)/16 Timer 1 overflow signal External clock from the P32/TIM2 pin The count source of timer 2 is selected by setting bits 4 and 1 of the timer 12 mode register (address 00F416 ). When timer 1 overflow signal is a count source for the timer 2, the timer 1 functions as an 8bit prescaler. Timer 2 interrupt request occurs at timer 2 overflow.
• • •
(3) Timer 3
Timer 3 can select one of the following count sources: f(XIN)/16 External clock from the P33/TIM3 pin and the HSYNC pin The count source of timer 3 is selected by setting bits 5 and 0 of the timer 34 mode register (address 00F516). Timer 3 interrupt request occurs at timer 3 overflow.
7
0 Timer 34 mode register (TM34MR : address 00F516 ) Timer 3 count source selection bit 0 : f (XIN ) /16 1 : External clock source (bits) Timer 4 internal count source selection bit 0 : Timer 3 overflow signal 1 : f (XIN ) /16 Timer 3 count stop bit 0 : Operation 1 : Stop Timer 4 count stop bit 0 : Operation 1 : Stop Timer 4 count source selection bit 0 : Internal clock source 1 : f (XIN ) /2 Timer 3 external count source selection bit 0 : P33 /TIM3 pin input 1 : HSYNC pin input
• •
(4) Timer 4
Timer 4 can select one of the following count sources: f(XIN)/16 f(XIN)/2 Timer 3 overflow signal The count source of timer 3 is selected by setting bits 4 and 1 of the timer 34 mode register 2 (address 00F516). When timer 3 overflow signal is a count source for the timer 4, the timer 3 functions as an 8bit prescaler. Timer 4 interrupt request occurs at timer 4 overflow.
• • •
At reset, timers 3 and 4 are connected by hardware and “FF 16” is automatically set in timer 3; “0716” in timer 4. The f(X IN)/16 is selected as the timer 3 count source. The internal reset is released by timer 4 overflow at these state, the internal clock is connected . At execution of the STP instruction, timers 3 and 4 are connected by hardware and “FF16” is automatically set in timer 3; “0716” in timer 4. However, the f(XIN)16 is not selected as the timer 3 count source. So
Fig. 6 Structure of timer-related registers
11
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
Data bus
8
1/4096
Timer 1 latch (8) 8
XIN
1/2
1/8 T12M0 T12M2 T12M4
Timer 1 (8) 8
Timer 1 interrupt request
8
Timer 2 latch (8) 8 P32/TIM2 D.F. T12M1 T12M3 8 Timer 2 (8) Timer 2 interrupt request
8 HSYNC FF16 P33/TIM3 D.F. T34M5 Timer 3 latch (8) 8 Timer 3 (8) T34M0 T34M2 8 Timer 3 interrupt request Reset STP instruction
8 0716 Timer 4 latch (8) 8 Timer 4 (8) T34M4
Selection gate : Connected to black colored side at reset.
T34M1
Timer 4 interrupt request 8
T34M3
T12M : Timer 12 mode register T34M : Timer 34 mode register Notes 1 : “H” pulse width of external clock inputs TIM2 and TIM3 needs 4 machine cycles or more. 2 : When the external clock source is selected, timers 2 and 3 are counted at a rising edge of input signal. 3 : In the stop mode or the wait mode, external clock inputs TIM2 and TIM3 cannot be used.
Fig. 7 Timer block diagram
12
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
SERIAL I/O
M37210M3-XXXSP has a serial I/O. A block diagram of the serial I/O is shown in Figure 8. Synchronous input/output clock (SCLK), and the serial I/O pins (SOUT, SIN) are used as port P4. The serial I/O mode registers (address 00DC16) are 8-bit registers. Bits 0, 1 and 2 of these registers are used to select a synchronous clock source.
Bit 3 decides whether parts of P4 will be used as a serial I/O or not. To use P42 as a serial input, set the directional register bit which corresponds to P42 to “0”. For more information on the directional register, refer to the I/O pin section. The serial I/O function is discussed below. The function of the serial I/O differs depending on the clock source ; external clock or internal clock.
Data bus XIN 1/2 1/2
Frequency divider
Synchronization circuit
SM2
1/4 1/8 1/16 SM1 SM0
P41 latch P41/SCLK SM3 P40 latch P40/SOUT SM3 P42/SIN SM6
Selection gate : Connected to black colored side at reset.
Serial I/O counter (8) SM5 : LSB↔MSB Serial I/O shift register (8) (address 00DD16) 8
Serial I/O interrupt request
Fig. 8 Serial I/O block diagram
13
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
The serial I/O counter is set to 7 when data is stored in the serial I/O register. At each falling edge of the transfer clock, serial data is output to SOUT. During the rising edge of this clock, data can be input from SIN and the data in the serial I/O register will be shifted 1 bit. Transfer direction can be selected by bit 5 of serial I/O mode register. After the transfer clock has counted 8 times, the serial I/O register will be empty and the transfer clock will remain at a high level. At this time the interrupt request bit will be set. External clock- If an external clock is used, the interrupt request will be sent after the transfer clock has counted 8 times but transfer clock will not stop. Due to this reason, the external clock must be controlled from the outside. The external clock should not exceed 1MHz at a duty cycle
of 50%. The timing diagram is shown in Figure 9. When using an external clock for transfer, the external clock must be held at “H” level when the serial I/O counter is initialized. When switching between the internal clock and external clock, the switching must not be performed during transfer. Also, the serial I/O counter must be initialized after switching. Notes 1: On programming, note that the serial I/O counter is set by writing to the serial I/O register with the bit managing instructions as SEB and CLB instructions. 2: When an external clock is used as the synchronizing clock, write transmit data to the serial I/O register at “H” of the transfer clock input level.
Sync. clock Transfer clock Serial I/O register write signal Serial I/O output SOUT Serial I/O input SIN D0 D1 D2 D3 D4 D5 D6
(Note 1) D7
Notes 1 : If internal clock is selected, the Sout pin is at high impedance after transfer is completed. 2 : When an external clock is used as the synchronous clock, write the transmit data to the serial I/O shift register at “H” of the transfer clock input level.
Interrupt request bit set
Fig. 9 Serial I/O timing (for LSB first)
14
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
7
0 Serial l/O mode register (SM : address 00DC16) Internal synchronous clock selection bits 00 : f (XIN) /4 01 : f (XIN) /16 10 : f (XIN) /32 11 : f (XIN) /64 Synchronous clock selection bit 0 : External clock 1 : Internal clock Serial l/O port selection bit 0 : P40, P41 1 : SOUT1,S CLK signal output pins Fix this bit to “0” Transfer direction selection bit 0 : LSB first 1 : MSB first Serial input pin selection bit 0 : Input from SIN pin 1 : Input from SOUT pin
Serial I/O common transmission/reception mode. Write 1 to bit 6 of serial I/O mode register, and signals SIN and SOUT switch internal to be able to serial data transmission/reception. Figure 11 shows signals on serial I/O common transmission/reception mode. Note : Receive the serial data after writing “FF16 ” to the serial I/O register.
Fig. 10 Structure of serial I/O mode register
P41/SCLK
clock1
P40/SOUT (/IN)
Input or output “1” SM6
The transmission mode
Serial I/O shift register “0” The reception mode Port P42 data
P42/SIN
Fig. 11 Signals on serial I/O common transmission/reception mode
15
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
PWM OUTPUT CIRCUIT (1) Introduction
The M37210M3-XXXSP/FP and M37210M4-XXXSP are equipped with one 14-bit PWM (DA) and eight 6-bit PWMs (PWM0-PWM7), and the M37211M2-XXXSP is equipped with six 6-bit PWMs (PWM0-PWM5). The 14-bit resolution gives DA the minimum resolution bit width of 500ns (for f(XIN) = 4MHz) and a repeat period of 8192µs. PWM0-PWM7 have a 6-bit resolution with minimum resolution bit width of 16 ms and repeat period of 1024µs. Block diagram of the PWM is shown in Figure 16. The PWM timing generator section applies individual control signals to DA and PWM0-7 using clock input XIN divided by 2 as a reference signal.
within one period in the circuit internal section. Refer to Figure 13 (a). Six different pulses can be output from the PWM. These can be selected by bits 0 through 5. Depending on the content of the 6-bit PWM latch, pulses from 5 to 0 are selected. The PWM output is the difference of the sum of each of these pulses. Several examples are shown in Figure 13 (b). Changes in the contents of the PWM latch allows the selection of 64 lengths of high-level area outputs varying from 0/64 to 63/64. A length of entirely high-level output cannot be output, i.e. 64/64.
(5) 14-bit PWM Operation
The output example of the 14-bit PWM is shown in Figure 14. The 14-bit PWM divides the data within the PWM latch into the lower 6 bits and higher 8 bits. A high-level area within a length DH times τ is output every short area of t = 256 τ =128µs as determined by data DH of the higher 8 bits. Thus, the time for the high-level area is equal to the time set by the lower 8 bits or that plus τ. As a result, the short-area period t ( = 128µ s, approx. 7.8 kHz) becomes an approximately repetitive period.
(2) Data Setting
The output pins PWM0-3 are in common with port P6 and PWM4-7 are in common with port P00-P03. For PWM output, each PWM output selection bit (bit 1 to 7 of PWM output control register 1, bit 0, 1 of PWM output control register 2, should be set. When DA is used for output, first set the higher 8-bit of the DA-H register (address 00CE16), then the lower 6-bit of the DA-L register (address 00CF16). When one of the PWM0-7 is used for output, set the 6-bit in the PWM0-7 register (address 00D0 16 t o 00D416, 00F616 t o 00F816), respectively.
(6) Output after Reset
At reset the output of port P6 is in the high impedance state and the contents of the PWM register and latch are undefined. Note that after setting the PWM register, its data is transferred to the latch. Table 2. Relation between the low-order 6 bits of data and high-level area increase space
6 low-order bits of data Area longer by τ than that of other tm (m = 0 to 63)
LSB
(3) Transferring Data from Registers to PWM Circuit
The data written to the PWM registers. 8 bits of the DA-H register is transferred to 14-bit PWM circuit when writing to lower 6 bits of the DA-L register.
(4) Operation of the 6-bit PWMs
The timing diagram of the eight 6-bit PWMs (PWM0-7) is shown in Figure 13. One period (T) is composed of 64 (26) segments. There are six different pulse types configured from bits 0 to 5 representing the significance of each bit. These are output
000000 000001 000010 000100 001000 010000 100000
Nothing m = 32 m = 16, 48 m = 8, 24, 40, 56 m = 4, 12, 20, 28, 36, 44, 52, 60 m = 2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 50, 54, 58, 62 m = 1, 3, 5, 7, ................................................... 57, 59, 61, 63
16
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
Data bus Selection gate : connected to black colored side at reset.
bit 0
DA-H register (address 00CE16)
bit 7
Pass gate
(14-bit)
MSB
DA-L register (address 00CF16)
LSB
8
6
14
6
PN2 PN4 14-bit PWM circuit PW1 XIN 1/2 PW0 PWM0 register (address 00D016)
bit 5 bit 0
DA D-A
Timing generator for PWM
8
PN3 6-bit PWM circuit
P60 D60 PW2 P61 D61 PW3 P62 D62 PW4 P63 D63 PW5 P00 D00 PW6 P01 D01 PW7 P02 D02 PN0 P03 D03 PN1
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
PWM6(Note)
PWM7(Note)
Note : The M37211M2-XXXSP can not output the PWM.
Inside of
is as same contents with the others.
PW : PWM output control register 1 PN : PWM output control register 2 D0 : Port P0 direction register P0 : Port P0 D6 : Port P6 directional register P6 : Port P6
Fig. 12 PWM block diagram
17
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
1 Bit 5
3
5
7
9
19
39
59
Bit 4 2 Bit 3 4 Bit 2 8 Bit 1 16 Bit 0 32 48
24 40 56
6
10
14
18
22
26
30
34
38
42
46
50
54
58
62
12
20
28
36
44
52
60
(a) Pulses showing the weight of each bit
0016 (0) 0116 (1) 0616 (24) 3F16 (63) T = 64t PWM output t = 10µs T = 1024µs
f (XIN) = 4MHz
(b) Example of 6-bit PWM output
Fig. 13 6-bit PWM timing
18
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
Set “2C16” to DA-H register
Set “2816” to DA-L register
[DA-H register] 0 bit 7
0
1
0
1
1
0
0 bit 0
[DA-L register]
1
0
1
0
0
0 bit 0
After writing of DA-L bit 13 [DA latch] 0 0 1 0 1 1 0 0 1 0 1 0 0
After writing bit 0 0
These bits decide “H” level area of fundamental waveform “H” level area of bit bit ( fundamental waveform ) = ( Minimum 0.5µs ) ! ( High-order 8latch ) durations value of DA
These bits decide smaller intervals tm in which “H” level area is [“H” level area of fundamental waveform plus r]
Fundamental waveform
0.5µs ! 44
Waveform of smaller intervals tm specified by the lower 6 bits
0.5µs ! 45
0.5µs 14-bit 2C 2B 2A … 03 02 01 00 PWM output 8-bit counter 14-bit 2C 2B 2A … 03 02 01 00 PWM output 8-bit counter
FF FE FD … D6 D5 D4 D3 … 02 01 00
FF FE FD … D6 D5 D4 D3 … 02 01 00
The fundamental waveform of smaller intervals tm which is not specified by the lower 6 bits is not changed
0.5µs ! 45
τ = 0.5µs
14-bit PWM output
t0
Low-order 6-bit output of DA latch
t1
t2
t3
t4
t5
t59
t60
t61
t62
t63
T = 8192µs
Fig. 14 14-bit PWM output example (f (XIN) = 4MHz)
19
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
7
0 PWM output control register 1 (PW : address 00D516) DA, PWM count source STOP bit 0 : Supply 1 : Stop DA/PN4 output selection bit 0 : DA (14-bit PWM) output 1 : PN4 (general-purpose) output P60/PWM0 output selection bit 0 : P60 (general-purpose) output 1 : PWM0 (6-bit PWM) output P61/PWM1 output selection bit 0 : P61 (general-purpose) output 1 : PWM1 (6-bit PWM) output P62/PWM2 output selection bit 0 : P62 (general-purpose) output 1 : PWM2 (6-bit PWM) output P63/PWM3 output selection bit 0 : P63 (general-purpose) output 1 : PWM3 (6-bit PWM) output P00/PWM4 output selection bit 0 : P00 (general-purpose) output 1 : PWM4 (6-bit PWM) output P01/PWM5 output selection bit 0 : P01 (general-purpose) output 1 : PWM5 (6-bit PWM) output
Note : Fix this bit to “0” (M37211M2-XXXSP).
7
0 PWM output control register 2 (PN : address 00D616) P02/PWM6 output selection bit (Note) 0 : P02 (general-purpose) output 1 : PWM6 (6-bit PWM) output P03/PWM7 output selection bit (Note) 0 : P03(general-purpose) output 1 : PWM7 (6-bit PWM) output DA output polarity selection bit 0 : Positive polarity 1 : Negative polarity 6-bit PWM output polarity selection bit 0 : Positive polarity 1 : Negative polarity D-A pin general-purpose output register 0 : Output “L” 1 : Output “H”
Fig.15 Structure of PWM output control registers 1 and 2
20
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
A-D COMPARATOR
Block diagram of A-D comparator is shown in Figure 18. A-D comparator consists of 5-bit D-A converter and comparator. The A-D control register can generate 1/64 V CC-step internal analog voltage based on the settings of bits 0 to 4. Table 3 gives the relation between the descriptions of A-D control register bits 0 to 4 and the generated internal analog voltage. The comparison result of the analog input voltage and the internal analog voltage is stored in the A-D control register, bit 5. After selection of an analog input pin by bits 0-2 of A-D mode register (address 00EE16), the digital value corresponding to the internal analog voltage to be compared is then written in the A-D control register, bit 0 to 3 and an analog input pin is selected. After 16 machine cycle, the voltage comparison is completed. 7 0 A-D control register (ADC : address 00EF16) D-A converter set bits (refer to table 3) Strage bit of comparison result 0 : Input voltage < reference voltage 1 : Input voltage > reference voltage
Fig. 16 Structure of A-D control register Table 3. Relationship between the contents of A-D control register and reference voltage A-D control register Bit4 0 0 0 …………………… Bit 3 0 0 0 …………………… Bit 2 0 0 0 …………………… Bit 1 0 0 1 …………………… Bit 0 0 1 0 …………………… Reference voltage Vref 1/64 VCC 3/64 VCC 5/64 VCC …………………… 27/64 VCC 29/64 VCC 31/64 VCC Bit 0
7
0 A-D mode regiser (ADM : address 00EE16) A-D input pin selection bits 0 0 0 : A-D1 0 0 1 : A-D2 0 1 0 : A-D3 0 1 1 : A-D4 1 0 0 : A-D5 101: These are not 110: available 111:
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
Fig. 17 Structure of A-D mode register
Data bus
A-D mode register Comparator control Bits 0 to 2
P15/A-D1 P16/A-D2 P17/A-D3 P35/A-D4 P42/A-D5
A-D control register Analog signal switch Comparator Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
Switch tree
Resistor ladder
Fig. 18 A-D comparator block diagram
21
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
CRT DISPLAY FUNCTIONS (1) Outline of CRT Display Functions
Table 4 outlines the CRT display functions of the M37210M3-XXXSP. The M37210M3-XXXSP incorporates a 18 columns ! 2 lines CRT display control circuit. CRT display is controlled by the CRT display control register. Up to 96 kinds of characters can be displayed, and colors can be specified for each character. Four colors can be displayed on one screen. A combination of up to 7 colors can be obtained by using each output signal (R, G and B). Characters are displayed in a 12 ! 16 dot configuration to obtain smooth character patterns (refer to Figure 19). The following shows the procedure how to display characters on the CRT screen. Table 4. Outline of CRT display functions Parameter Number of display character Character configuration Kinds of character Character size Kinds of color Color Coloring unit Display expansion Raster coloring Functions 18 characters ! 2 lines 12 ! 16 dots (refer to Figure 19) 96 3 kinds 1 screen : 4 kinds A character Possible (multiline display) Possible (maximum 7 kinds)
Set the character to be displayed in display RAM. Set the display color by using the color register. Specify the color register in which the display color is set by using the display RAM. Specify the vertical position and character size by using the vertical position register and the character size register. Specify the horizontal position by using the horizontal position register. Write the display enable bit to the designated block display flag of the CRT control register. When this is done, the CRT starts operation according to the input of the VSYNC signal. The CRT display circuit has an extended display mode. This mode allows multiple lines (more than 3 lines) to be displayed on the screen by interrupting the display each time one line is displayed and rewriting data in the block for which display is terminated by software. Figure 21 shows a block diagram of the CRT display control circuit. Figure 20 shows the structure of the CRT display control register.
7
0 CRT control register (CC : address 00EA16) Display of all blocks control bit (Note) 0 : Display of all blocks off 1 : Display of all blocks on Display of block 1 control bit 0 : Display of block 1 off 1 : Display of block 1 on Display of block 2 control bit 0 : Display of block 2 off 1 : Display of block 2 on
12 dots
Note : Display is controlled by logical product (AND) between the allblocks display control bit and each block display control bit
Fig. 20 Structure of CRT control register
16 dots
Fig. 19 CRT display character configuration
22
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
OSC1
OSC2
HSYNC VSYNC
(Address 00EA16) CRT control register (Addresses 00E116 to 00E216) Vertical position registers Display oscillation circuit
(Address 00E416) Character size register Display position control circuit (Address 00E016) Horizontal position register (Address 00E516) Border selection register
Display control circuit
RAM for display 9 bits × 18 × 2
ROM for display 12 bits × 16 × 96
(Addresses 00E616 to 00E916)
Color registers
Shift register 12 bits
Shift register 12 bits
(Address 00EC16) CRT port control register Data bus R
Output circuit
G
B
OUT
Fig. 21 Block diagram of CRT display control circuit
23
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(2) Display Position
The display positions of characters are specified in units called a “block”. There are two blocks, block 1 and block 2. Up to 18 characters can be displayed in one block (refer to (4) Memory for Display). The display position of each block in both horizontal and vertical directions can be set by software. The horizontal direction is common to all blocks, and is selected from 64-step display positions in units of 4Tc (Tc = oscillating cycle for display). The display position in the vertical direction is selected from 128-step display positions for each block in units of four scanning lines. Block 2 is displayed after the display of block 1 perfectly (fig. 24(a)). Then if the display of block 2 starts during the display of block 1, only block 1 is displayed. As same, when multiline display, block 1 is displayed after the display of block 2 perfectly (fig. 24(b)). The vertical position can be specified from 128-step positions (four scanning lines per step) for each block by setting values 0016 to 7F16 to bits 0 to 6 in the vertical position register (addresses 00E116 and 00E215). Figure 22 shows the structure of the vertical position register.
7
0 Vertical position registers 1, 2 (CV1 : address 00E116) (CV2 : address 00E216) The vertical display start positions 128-step positions (0016 to 7F16)
Fig. 22 Structure of vertical position registers The horizontal direction is common to all blocks, and can be specified from 64-step display positions (4Tc per step (Tc = oscillating cycle for display) by setting values 0016 to 3F16 to bits 0 to 5 in the horizontal position register (address 00E016 ). Figure 23 shows the structure of the horizontal position register.
7
0 Horizontal position register (HR : address 00E016)
The horizontal display start positions 64-step positions (0016 to 3F16)
Fig. 23 Structure of horizontal position register
24
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(RH) CV1 Block 1 CV2 Block 2
(a) Example when each block is separated
CV1 CV2 Block 1
Block 2 CV1 Block 1 (second)
No display
No display
(b) Example when block 2 overlaps with block 1
Fig. 24 Display position
25
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(3) Character Size
The size of characters to be displayed can be selected from three sizes for each block. Use the character size register (address 00E416) to set a character size. The character size in block 1 can be specified by using bits 0 and 1 in the character size register ; the character size in block 2 can be specified by using bits 2 and 3. Figure 25 shows the structure of the character size register. The character size can be selected from three sizes : small size, medium size and large size. Each character size is determined by the number of scanning lines in the height (vertical) direction and the cycle of display oscillation ( = Tc) in the width (horizontal) direction. The small size consists of [one scanning line] ! [1 Tc] ; the medium size consists of [two scanning lines] ! [2 Tc] ; and the large size consists of [three scanning lines] ! [3 Tc]. Table 5 shows the relationship between the set values in the character size register and the character sizes. 7 0 Character size register (CS : address 00E416) Character size of block 1 selection bits 00 : Minimum size 01 : Medium size 10 : Large size 11 : This is not available Character size of block 2 selection bits 00 : Minimum size 01 : Medium size 10 : Large size 11 : This is not available
Fig. 25 Structure of character size register
Table 5. The relationship between the set values of the character size register and the character sizes Set values of the character size register CSn0 CSn1 0 0 1 1 0 1 0 1 Character size Minimum Medium Large Width (horizontal) direction Tc : oscillating cycle for display 1 Tc 2 Tc 3 Tc This is not available Height (vertical) direction scanning lines 1 2 3
Note : The display start position in the horizontal direction is not affected by the character size. In other words, the horizontal display start position is common to all blocks even when the character size varies with each block (refer to Figure 26).
26
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(4) Memory for Display
There are two types of memory for display : ROM of CRT display (addresses 300016 to 35FF16 , 380016 to 3DFF16) used to store character dot data (masked) and display RAM (addresses 200016 t o 20B116) used to specify the colors of characters to be displayed. The following describes each type of display memory. ROM for display (addresses 300016 to 35FF16 and 380016 to 3DFF16) The CRT display ROM contains dot pattern data for characters to be displayed. For characters stored in this ROM to be actually displayed, it is necessary to specify them by writing the character code inherent to each character (code determined based on the addresses in the CRT display ROM) into the CRT display RAM.
The CRT display ROM has a capacity of 3K bytes. Because 32 bytes are required for one character data, the ROM can contain up to 96 kinds of characters. The CRT display ROM space is broadly divided into two areas. The [vertical 16 dots] × [horizontal (left side) 8 dots] data of display characters are stored in addresses 300016 to 35FF 16 ; the [vertical 16 dots] × [horizontal (right side) 4 dots] data of display characters are stored in addresses 380016 to 3DFF16 (refer to Figure 27). Note however that the four upper bits in the data to be written to addresses 380016 to 3DFF16 must be set to “1” (by writing data F016 to FF16).
Table 6. Character code list Character code Contained up address of character data Left 8 dots lines Right 4 dots lines 300016 to 300F16 301016 to 301F16 302016 to 302F16 303016 to 303F16 : 310016 to 310F16 380016 to 380F16 381016 to 381F16 382016 to 382F16 383016 to 383F16 : 390016 to 390F16
Minimum
0016
0116
Medium 0216
0316 : 1016 Large
1116 Horizontal display start position : 4F16 Fig. 26 Display start position of each character size (horizontal direction) 5016 : 5D16
311016 to 311F16 : 34F016 to 34FF 16
391016 to 391F16 : 3CF0 16 to 3CFF16
350016 to 350F16 : 35D016 to 35DF 16 35E0 16 to 35EF16 35E0 16 to 35FF 16
3D0016 to 3D0F 16 : 3DD016 to 3DDF16 3DE016 to 3DEF16 3DF0 16 to 3DFF16
5E16
5F16
27
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
The character code used to specify a character to be displayed is determined based on the address in the CRT display ROM in which that character is stored. Assume that data for one character is stored at addresses 3XX016 to 3XXF16 (XX denotes 0016 to 5F16) and addresses 3YY016 to 3YYF16 (YY denotes 8016 to DF16), then the character code for it is “XX16”.
In other words, character code for any given character is configured with two middle digits of the four-digit (hexnotated) addresses 300016 to 35FF16 where data for that character is stored. Table 6 lists the character codes.
bit 7 3XX016 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3XXF16 0
0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0
0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0
0 0 0 0 0 1 1 1 0 0 1 0 0 0 0 0
0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 0
0 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0
0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 0
bit 0 0 0 0 0 0 1 1 1 0 0 1 0 0 0 0 0
bit 7 3XX016+80016 1 1 11 11 11 11 11 11 11 11 11 11 11 11 11 11 3XXF16+80016 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
bit 3 00 00 00 00 00 00 00 00 10 10 10 01 01 01 00 00
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Fig. 27 Display character stored area
28
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
RAM for display (address 200016 to 20B116 ) The CRT display RAM is allocated at addresses 200016 to 20B116 , and is divided into a display character code specifying part and display color specifying part for each block. Table 7 shows the contents of the CRT display RAM. When a character is to be displayed at the first character (leftmost) position in block 1, for example, it is necessary to write the character code to the seven low-order bits (bits 0 to 6) in address 200016 and the color register No. to the two low-order bits (bits 0 and 1) in address 208016. The color register No. to be written here is one of the four color registers in which the color to be displayed is set in advance. For details on color registers, refer to (5) Color Registers. The structure of the CRT display RAM is shown in Figure 27. Table 7. The contents of the CRT display RAM Block Display position (from left) 1st character 2nd character 3rd character : 16th character 17th character 18th character Not used 1st character 2nd character Block 2 3rd character : 16th character 17th character 18th character Not used Character code specification 200016 200116 200216 : 200F16 201016 201116 201216 : 201F16 202016 202116 202216 : 202F16 203016 203116 203216 : 203F16 Color specification 208016 208116 208216 : 208F16 209016 209116 209216 : 209F16 20A0 16 20A116 20A2 16 : 20AF16 20B0 16 20B116 20B2 16 : 20BF16
Block 1
29
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
Block 1 [Character specification] 1st character : 200016 to 18th character : 201116 7 0
Character code (0016 to 5F16) Specify 96 characters
[Color specification] 1st character : 208016 to 18th character : 209116 10
Specify color select mode 00 : Color register 0 specification 01 : Color register 1 specification 10 : Color register 2 specification 11 : Color register 3 specification
Block 2 [Character specification] 1st character : 202016 to 18th character : 203116 7 0
Character code (0016 to 5F16) Specify 96 characters
[Color specification] 1st character : 20A016 to 18th character : 20B116 10
Color register specification 00 : Color register 0 specification 01 : Color register 1 specification 10 : Color register 2 specification 11 : Color register 3 specification
Fig. 28 Structure of the CRT display RAM
30
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(5) Color Registers
The color of a displayed character can be specified by setting the color to one of the four color registers (CO0 to CO3 : addresses 00E616 to 00E9 16) and then specifying that color register with the CRT display RAM. There are three color outputs : R, G and B. By using a combination of these outputs, it is possible to set 23 -1 (when no output) = 7 colors. However, because only four color registers are available, up to four colors can be displayed at one time. R, G and B outputs are set by using bits 1 to 3 in the color register. Bit 5 is used to specify whether a character output or blank output. Figure 29 shows the structure of the color register.
(6) Multiline Display
The M37210M3-XXXSP can normally display two lines on the CRT screen by displaying two blocks at different vertical positions. In addition, it allows up to 16 lines to be displayed by using a CRT interrupt. The CRT interrupt works in such a way that when display of one block is terminated, an interrupt request is generated. In other words, character display for a certain block is initiated when the scanning line reaches the display position for that block (specified with vertical position register) and when the range of that block is exceeded, an interrupt is applied. Note : A CRT interrupt does occurs at the end of display regardless of display on or off. In other words, even if a block is set to off display with the display control bit of the CRT control register (address 00EA16 ), a CRT interrupt request occurs (refer to Figure 30).
7
0
Color registers 0,1,2,3 (CO0 : address 00E616) (CO1 : address 00E716) (CO2 : address 00E816) (CO3 : address 00E916) B signal output selection bit 0 : No character is output 1 : Character is output G signal output selection bit 0 : No character is output 1 : Character is output R signal output selection bit 0 : No character is output 1 : Character is output OUT signal output selection bit (Note) 0 : OUT pin outputs character 1 : OUT pin outputs blank
Note : When the character bordering function is used, the contents of this bit (bit 5) are invalied, and the OUT pin output becomes a border output.
Fig. 29 Structure of color registers
31
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
Block 1 (on display) “CRT interrupt” Block 2 (on display) “CRT interrupt” Block 1’ (on display) “CRT interrupt” Block 2’ (on display) “CRT interrupt” On display (“CRT interrupt” works after block)
Block 1 (off display) “CRT interrupt” Block 2 (off display) “CRT interrupt” Block 1’ (off display) “CRT interrupt” Block 2’ (off display) “CRT interrupt” Off display (“CRT interrupt” occurs after block)
(Note) : That is to say, “CRT interrupt” occurs even when it is off display by setting the display control flag of the CRT control register (address 00EA16 ).
Fig. 30 Timing of CRT interrupt
32
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(7) Character Border Function
An border of a one clock (one dot) equivalent size can be added to a character to be displayed in both horizontal and vertical directions. The border is output from the OUT pin. In this case, bit 5 in the color register (contents output from the OUT pin) is nullified, and the border is output from the OUT pin instead.
Border can be specified in units of block by using the border select register (address 00E516 ). Table 8 shows the relationship between the values set in the border select register and the character border function. Figure 32 shows the structure of the border select register.
Table 8. The relationship between the value set in the border selection register and the character border function Border selection register MDn0 0 1 Functions Ordinary Border including character Example of output R, G, B output OUT output R, G, B output OUT output
7
0 Border selection register (MD : address 00E516) Block 1 OUT signal output border selection bit 0 : Same output as R, G, B is output 1 : Border output Block 2 OUT signal output border selection bit 0 : Same output as R, G, B is output 1 : Border output
Fig. 32 Structure of border selection register
is border. is display by character data.
Fig. 31 Example of border
33
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
(8) CRT Output Pin Control
CRT output pins R, G, B and OUT are respectively shared with port P52, P53, P54 and P55. When the corresponding bits in the port P5 control register (address 00CB16) are cleared to “0”, the pins are set for CRT output ; when the bits are set to “1”, the pins function as port P5 (general- purpose output pins). The polarities of CRT outputs (R, G, B and OUT, as well as HSYNC and VSYNC) can be specified by using the CRT port control register (address 00EC16). Use bits 0 to 4 in the CRT port control register to set the output polarities of HSYNC , VSYNC , R/G/B and OUT. When these bits are cleared to “0”, a positive polarity is selected ; when the bits are set to “1”, a negative polarity is selected. Bits 5 to 7 in the CRT port control register are used to specify pin by pin whether normal video signals or R-MUTE, G-MUTE, and BMUTE signals are output from each pin (R, G, B). When set for RMUTE, G-MUTE, and B-MUTE outputs, the whole background colors of the screen become red, green, and blue. Figure 33 shows the structure of the CRT port control register.
7
0 Polarity register (CRTP : address 00EC16) HSYNC input polarity selection bit 0 : Positive polarity 1 : Negative polarity VSYNC input polarity selection bit 0 : Positive polarity 1 : Negative polarity R/G/B output polarity selection bit 0 : Positive polarity 1 : Negative polarity OUT output polarity selection bit 0 : Positive polarity 1 : Negative polarity R pin output switch bit 0 : R signal output 1 : R-MUTE signal output G pin output switch bit 0 : G signal output 1 : G-MUTE signal output B pin output switch bit 0 : B signal output 1 : B-MUTE signal output
Fig. 33 Structure of CRT port control register
34
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
INTERRUPT INTERVAL DETERMINATION FUNCTION
The M37210M3-XXXSP incorporates an interrupt interval determination circuit. This interrupt interval determination circuit has an 8-bit binary up counter as shown in Figure 34. Using this counter, it determines an interval or a pulse width on the INT1 or INT2 (refer to Figure 36). The following describes how the interrupt interval is determined. 1. The interrupt input to be determined (INT1 input or INT2 input) is selected by using bit 2 in the interrupt interval determination control register (address 00D816 ). When this bit is cleared to “0”, the INT1 input is selected ; when the bit is set to “1”, the INT2 input is selected. 2. When the INT1 input is to be determined, the polarity is selected by using bit 3 of the interrupt interval determination control register ; when the INT2 input is to be determined, the polarity is selected by using bit 4 of the interrupt interval determination control register. When the relevant bit is cleared to “0”, determination is made of the interval of a positive polarity (rising transition) ; when the bit is set to “1”, determination is made of the interval of a negative po-
larity (falling transition). 3. The reference clock is selected by using bit 1 of the interrupt interval determination control register. When the bit is cleared to “0”, a 64ms clock is selected ; when the bit is set to “1”, a 32µ s clock is selected (based on an oscillation frequency of 4MHz in either case). 4. Simultaneously when the input pulse of the specified polarity (rising or falling transition) occurs on the INT1 pin (or INT2 pin), the 8bit binary up counter starts counting up with the selected reference clock (64µs or 32µ s). 5. Simultaneously with the next input pulse, the value of the 8-bit binary up counter is loaded into the determination register (address 00D716) and the counter is immediately reset (0016 ). The reference clock is input in succession even after the counter is reset, and the counter restarts counting up from “0016”. 6. When count value “FE16 ” is reached, the 8-bit binary up counter stops counting. Then, simultaneously when the next reference clock is input, the counter sets value “FF16 ” to the determination register.
32µs 64µs RE1 INT2 Interrupt interval determination register RE2 8 Address 00D716 Control circuit 8-bit binary up counter RE0 8
INT1 (Note)
Selection gate : Connected to black colored side at reset.
Data bus
RE : Interrupt interval determination control register Note : The pulse width of external interrupt INT1 and INT2 needs 5 or more machine cycles.
Fig. 34 Block diagram of interrupt interval determination circuit
35
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
7
0 Interrupt interval determination control register (RE : address 00D816) Interrupt interval determination circuit operation control bit 0 : Stop 1 : Operation Reference clock selection bit (At f (XIN) = 4MHZ) 0 : 64ms 1 : 32ms External interrupt input pin selection bit 0 : INT1 input 1 : INT2 input INT1 pin input polarity switch bit 0 : Positive polarity input 1 : Negative polarity input INT2 pin input polarity switch bit 0 : Positive polarity input 1 : Negative polarity input Interrupt interval determination mode switch bit 0 : Interrupt interval determination mode 1 : Pulse width determination mode
Fig. 35 Structure of interrupt space distinguish control register
INT1 or 2 input RE5 0 0 1 1 RE4 (RE3) 0 1 0 1 count interval
REi : Bitsi ( i = 3, 4, 5) of interrupt space distinguish control register (address 00D816 )
Fig. 36 Interrupt space distinguish control register setting value and the measuring interval
36
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
RESET CIRCUIT
The M37210M3-XXXSP is reset according to the sequence shown in Figure 39. It starts the program from the address formed by using the content of address FFFF1 6 as the high order address and the content of the address FFFE16 as the low order address, when the RESET pin is held at “L” level for no less than 2µs while the power voltage is 5V ± 10% and the crystal oscillator oscillation is stable and then returned to “H” level. The internal initializations following reset are shown in Figure 37. An example of the reset circuit is shown in Figure 38. The reset input voltage must be kept below 0.6V until the supply voltage surpasses 4.5V. Power source voltage 0V Reset input voltage 0V
Power on 4.5V
0.6V
27 1 5
M51953AL
Vcc
30
RESET
4 3 0.1 F 26 Vss
M37210M4-XXXSP Fig. 38 Example of reset circuit
Address (1) Port P0 directional register (2) Port P1 directional register (3) Port P2 directional register (4) Port P3 (5) Port P3 directional register (6) Port P4 (7) Port P4 directional register (8) Port P5 (9) Port P5 directional register (10) Port P6 (11) Port P6 directional register (12) 14DA-L register (13) PWM0 register (14) PWM1 register (15) PWM2 register (16) PWM3 register (17) PWM4 register (18) PWM output control register 1 (19) PWM output control register 2(Note 2) (20) Interrupt interval determination register ( 0 0 C 1 16) … ( 0 0 C 3 16) … ( 0 0 C 5 16) … ( 0 0 C 6 16) … ( 0 0 C 7 16) … ( 0 0 C 8 16) … ( 0 0 C 9 16) … ( 0 0 C A 16) … ( 0 0 C B 16) … ( 0 0 C C 16) … ( 0 0 C D 16) … ( 0 0 C F 16) … ( 0 0 D 0 16) … ( 0 0 D 1 16) … ( 0 0 D 2 16) … ( 0 0 D 3 16) … ( 0 0 D 4 16)… ( 0 0 D 5 16) … ( 0 0 D 6 16) … ( 0 0 D 7 16) … 0016 00000 0016 000000 0000000 000000 0000 1111 1111 000 00 0016 0016 0016 (30) Color register 2 (31) Color register 3 (32) CRT control register (33) CRT port control register (34) A-D mode register (35) A-D control register (36) Timer 1 (37) Timer 2 (38) Timer 3 (39) Timer 4 (40) Timer 12 mode register (41) Timer 34 mode register (42) PWM5 register (43) PWM6 register (Note 3) (44) PWM7 register (Note 3) (45) CPU mode register (46) Interrupt request register 1 (47) Interrupt request register 2 (48) Interrupt control register 1 (49) Interrupt control register 2 (50) Processor status register (51) Program counter ( 0 0 E 8 16) … ( 0 0 E 9 16) … ( 0 0 E A 16) … ( 0 0 E C 16) … 0 0 0 0 ( 0 0 E E 16)… ( 0 0 E F 16)… ( 0 0 F 0 16) … ( 0 0 F 1 16) … ( 0 0 F 2 16) … ( 0 0 F 3 16) … ( 0 0 F 4 16) … ( 0 0 F 5 16) … ( 0 0 F 6 16) … ( 0 0 F 7 16) … ( 0 0 F 8 16) … ( 0 0 F B 16)… 1 1 1 1 1 1 0 0 ( 0 0 F C 16) … ( 0 0 F D 16) … 0 000000 0 000 0 0 000 000 000 000 000 00000 FF16 0716 FF16 0716 000000 000000
( 0 0 F E 16) … 0 0 0 0 0 0 0 0 ( 0 0 F F 16) … 0 0 0 0 0 ( P S )… ( P C M)… ( P C L)… 1
Contents of address F F F F 16 Contents of address F F F E 16
… (21) Interrupt interval determination control register ( 0 0 D 8 16) (22) Serial I/O mode register (23) Horizontal position register (24) Vertical position register 1 (25) Vertical position register 2 (26) Character size register (27) Border selection register (28) Color register 0 (29) Color register 1 ( 0 0 D C 16) … ( 0 0 E 0 16) … ( 0 0 E 1 16) … ( 0 0 E 2 16) … ( 0 0 E 4 16) … ( 0 0 E 5 16) … ( 0 0 E 6 16) … ( 0 0 E 7 16) …
Notes 1 : Since the contents of both registers other than those listed above and the RAM are undefined at reset, it is necessary to set initial values. “0” is read from all bits which is not used.
0 0 000 000
2 : The M37211M2-XXXSP is
000
3 : The M37211M2-XXXSP dose not have this register.
Fig. 37 Internal state at reset
37
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
XIN φ RESET Internal RESET SYNC Address Data ? ? ? ? 00,S 00,S-1 00,S-2 FFFE FFFF PCH PCL PS ADL
ADH, ADL
Reset address from the vector table ADH
32768 count of XIN clock cycle (Note 3)
Note 1 : f (XIN ) and f ( φ ) are in the relationship : f (XIN) = 2 · f ( φ ). 2 : A question mark (?) indicates an undefined state that depends on the previous state. 3 : Immediately after a reset, FF16 is automatically set in timer 3 and 0716 in timer 4 and timer 4, timer 3 and the clock (f (XIN) divided by 16) are connected in series. Reset state is canceled by the overflow signal of timer 4.
Fig. 39 Reset sequence
38
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
I/O PORTS
(1) Port P0 Port P0 is an 8-bit I/O port with N-channel open-drain output. As shown in the memory map (Figure 3), port P0 can be accessed at zero page memory address 00C016. Port P0 has a directional register (address 00C116) which can be used to program each individual bit as input (“0”) or as output (“1”). If the pins are programmed as output, the output data is latched to the port register and then output. When data is read from the output port the output pin level is not read, only the latched data in the port register is read. This allows a previously output value to be read correctly even though the output voltage level is shifted up or down. Pins set as input are in the floating state and the signal levels can thus be read. When data is written into the input port, the data is latched only to the port latch and the pin still remains in the floating state. Ports P0 0-P03 are in common with 6-bit PWM outputs PWM4PWM7. For the M37211M2, ports P00 and P0 1 are in common with 6-bit PWM outputs PWM4 and PWM5. (2) Port P1 Port P1 has basically the same function as port P0 except the output structure is CMOS output. But, pins P1 5-P1 7 are input ports and in common with analog input pins A-D1-A-D3. (3) Port P2 Port P2 has basically the same function as port P1.
(4) Port P3 Port P3 are a 2-bit I/O port and a 4-bit input port with function similar to port P2, but the output structure of P30, P31 is CMOS output. P32, P33 are in common with the external clock input pins of timer 2 and 3. P34, P3 5 are in common with the external interrupt input pins INT1, INT2 and P35 with the analog input pin of A-D comparator A-D4. (5) Port P4 Port P4 are a 2-bit I/O port and a 1-bit input port with function similar to port P2, but the output structure is N-channel opendrain output. When a serial I/O function is selected, P40-P4 2 are in common with pins SOUT, SCLK and SIN. (6) OSC1, OSC2 pins Clock input/output pins for CRT display function. (7) HSYNC, VSYNC pins HSYNC is a horizontal synchronizing signal input pin for CRT display. VSYNC is a vertical synchronizing signal input pin for CRT display. (8) R, G, B, OUT pins This is an 4-bit output pin for CRT display and in common with P52-P55. (9) Port P6 Port P6 is an 4-bit output port with function similar to port P0, but the output structure is N-channel opendrain output. This port is in common with 6-bit PWM output pin PWM0-PWM3. (10) D-A pin This is a 14-bit PWM output pin.
39
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
Port P0 Directional register
N-channel open-drain output
Port P0 Data bus Port latch
Port P10 – P14, P2, P30, P31 CMOS 3-state output Directional register
Data bus
Port latch
Port P10 – P14, P2, P30, P31
Port P40,P41 Directional register SIN/SCLK
N-channel open-drain output
Port P40,P41 Data bus Port latch
Note : P40 , P41 can also be used as serial I/O pins.
Fig. 40 I/O pin block diagram (1)
40
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
N-channel open-drain output Port P6 Port P6 Data bus Port latch
Note : P6 can also be used as 6-bit PWM output pins.
D-A, R, G, B, OUT CMOS output HSYNC, VSYNC Schmitt input
Internal circuit
HSYNC, VSYNC
Internal circuit
D-A, R, G, B, OUT
Note : Pins R, G, B, and OUT can also be used as output ports P52 – P55.
Port P15 – P17
Data bus
Port P15 – P17
TIM2, TIM3, INT1, INT2, or SIN Data bus
Ports P32 – P35, P42
Note : P15 – P17 are in common with input Pins for A-D comparator. P32, P33 are in common with timer inputs. P34, P35 are in common with external interrupt inputs. P42 is in common with input pins of serial I/O pins.
Fig. 41 I/O pin block diagram (2)
41
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
CLOCK GENERATING CIRCUIT
The built-in clock generating circuit is shown in Figure 44. When the STP instruction is executed, the internal clock φ stops oscillating at “H” level. At the same time, timers 3 and 4 are connected in hardware and “FF16” is set in the timer 3, “0716 ” is set in the timer 4. Select f(XIN)/16 as the timer 3 count source (set bit 0 of the timer 34 mode register to “0” before the execution of the STP instruction). And besides, set the timer 3 and timer 4 interrupt enable bits to disabled (“0”) before execution of the STP instruction. The oscillator is restarted when an external interrupt is accepted. However, the internal clock φ keeps its “H” level until timer 4 overflows. This is because the oscillator needs a set-up period if a ceramic resonator or a quartz-crystal oscillator is used. When the WIT instruction is executed, the internal clock φ stops in the “H” level but the oscillator continues running. This wait state is cleared when an interrupt is accepted (Note). Since the oscillation does not stop, the next instructions are executed at once. To return from the stop or the wait state, set the interrupt enable bit to “1” before executing the STP or the WIT instruction. Note : In the wait mode, the following interrupts are invalid. (1) VSYNC interrupt (2) CRT interrupt (3) Timer 2 interrupt using P32/TIM2 pin input as count source (4) Timer 3 interrupt using P33/TIM3 pin input as count source (5) Timer 4 interrupt using f(XIN)/2 as count source The circuit example using a ceramic resonator (or a quartz crystal oscillator) is shown in Figure 42. Use the circuit constants in accordance with the resonator manufacture’s recommended values.
The example of external clock usage is shown in Figure 43 XIN is the input, and XOUT is open.
M37210M3-XXXSP XIN 24 XOUT 25
CIN
COUT
Fig. 42 Ceramic resonator circuit example
M37210M3-XXXSP XIN 24 Vcc External oscillation circuit Vss
Fig. 43 External clock input circuit example
Interrupt request Reset Interrupt disable flag I Reset WIT instruction R R STP instruction S S Q Q Q S
STP instruction
R
Internal clock φ
T34M0 1/2 1/8 Timer 3
Timer 4
T34M2 XIN XOUT TIM3
Selection gate: Connected to black colored side at reset.
Fig. 44 Clock generating circuit block diagram
42
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
PROGRAMMING NOTES
(1) The divide ratio of the timer is 1/ (n + 1). (2) Even though the BBC and BBS instructions are executed immediately after the interrupt request bits are modified (by the program), those instructions are only valid for the contents before the modification. At least one instruction cycle is needed (such as an NOP) between the modification of the interrupt request bits and the execution of the BBC and BBS instructions. (3) After the ADC and SBC instructions are executed (indecimal operation mode), one instruction cycle (such as an NOP) is needed before the SEC, CLC, or CLD instructions are executed. (4) An NOP instruction is needed immediately after the execution of a PLP instruction. (5) In order to avoid noise and latch-up, connect a bypass capacitor ( ≈ 0.1µ F) directly between the VCC pin and VSS pin using a thick wire.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production. (1) Mask ROM Order Confirmation Form (2) Mark Specification Form (3) Data to be written to ROM, in EPROM form (28-pin DIP type 27256, three identical copies)
PROM Programming Method
The built-in PROM of the blank One Time PROM version and built-in EPROM version can be read or programmed with a general-purpose PROM programmer using a special programming adapter.
Product M37210E4SP M37210E4FP
Name of Programming Adapter PCA4754 PCA4756
The PROM of the blank One Time PR OM version is not tested or screened in the assembly process and f ollowing processes. To ensure proper operation after programming, the procedure shown in Figure 45 is recommended to verify programming.
Programming with PROM programmer
Screening (Caution) (150 for 40 hours)
Verification with PROM programmer
Functional check in target device
Caution : The screening temperature is far higher than the storage temperature. Never expose to 150°C exceeding 100 hours.
Fig. 45 Programming and testing of One Time PROM version
43
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
ABSOLUTE MAXIMUM RATINGS
Symbol VCC VI VI Parameter Power source voltage Input voltage CNVSS Input voltage P00 – P07, P1 0 – P17, P2 0 – P27 , P30 – P35, P4 0 – P42, H SYNC, VSYNC, RESET, OSC1, XIN Output voltage P10 – P14, P20 – P27, P30 , P31, P40, P41, R, G, B, OUT, D-A, XOUT, OSC2 Output voltage P60 – P63, P00 – P07 “H” average output current R, G, B, OUT, P10 – P14, P20 – P23, P3 0, P31, D-A “L” average output current R, G, B, OUT, P10 – P1 4, P20 – P23, P3 0, P31, P4 0, P4 1 D-A “L” average output current P60 – P63 , P00 – P07 “L” average output current P24 – P27 Power dissipation Operating temperature Storage temperature Conditions Ratings – 0.3 to 6 – 0.3 to 6 – 0.3 to VCC + 0.3 Unit V V V
All voltages are based on VSS. Output transistors are cut off.
VO VO IOH
– 0.3 to V CC + 0.3 – 0.3 to 13 0 to 1 (Note 1)
V V mA
IOL1 IOL2 IOL3 Pd Topr Tstg
0 to 2 (Note 2) 0 to 1 (Note 2) 0 to 10 (Note 3) 550 – 10 to 70 – 40 to 125
mA mA mA mW °C °C
Ta = 25°C
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VSS VIH Parameter
(VCC = 5V ± 10%, Ta = –10 to 70°C unless otherwise noted) Limits Typ. 5.0 0 Unit V V V
VIL VIL IOH IOL1 IOL2 IOL3 fCPU fCRT fhs fhs
Power source voltage (Note 4) During the CPU and the CRT operation Power source voltage “H” input voltage P00 – P07, P1 0 – P17, P2 0 – P27 , P30 – P35, P4 0 – P42, H SYNC, VSYNC, RESET, XIN, OSC1, TIM2, TIM3, INT1, INT2, SIN, SCLK “L” input voltage P00 – P07, P1 0 – P17, P2 0 – P27 , P30 – P35, P4 0 – P42 “L” input voltage TIM2, TIM3, INT1, INT2, SIN, SCLK, HSYNC, VSYNC, RESET, XIN, OSC1 “H” average output current (Note 1) R, G, B, OUT, P10 – P14, P2 0 – P27, P3 0, P31 , D-A “L” average output current (Note 2) R, G, B, OUT, P10 – P14, P20 – P23, P3 0, P31, P4 0, P41, D-A “L” average output current (Note 2) P60 – P63, P00 – P07 “L” average output current (Note 3) P24 – P2 7 Oscillation frequency (for CPU operation)(Note 5) Oscillation frequency (for CRT display) Input frequency TIM2, TIM3, INT1, INT2 Input frequency SCLK
Min. 4.5 0 0.8VCC
Max. 5.5 0 VCC
0 0
0.4VCC 0.2VCC 1 2 1 10 8.1 6.0 100 1
V V mA mA mA mA MHz MHz kHz MHz
3.6 4.0
4.0 5.0
Notes 1 : The total current that flows out of the IC should be 20mA (max.). 2 : The total of IOL1 and IOL2 should be 30mA (max.). 3 : The total of IOL of port P24-P27 should be 20mA (max.). 4 : Connect 0.022µF or more capacitor externally between the V CC – VSS power source pins so as to reduce power source noise. Also connect 0.068µF or more capacitor externally between the V CC – CNVSS pins. 5 : Use a quartz-crystal oscillator or a ceramic resonator for CPU oscillation circuit.
44
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
ELECTRIC CHARACTERISTICS
Symbol Parameter
(VCC = 5V ± 10%, VSS = 0V, Ta = – 10 to 70°C, f (XIN) = 4MHz unless otherwise noted) Test conditions VCC = 5.5V f (XIN) = 4MHz C R T C R T OFF ON OFF ON Limits Typ. 10 20 20 30 – Unit mA mA µA V 0.4 0.4 3.0 0.5 0.5 0.7 1.3 5 V V
ICC
Power source current
VCC = 5.5V f (XIN) = 8MHz At stop mode VCC = 4.5V IOH = – 0.5mA VCC = 4.5V IOL = 0.5mA VCC = 4.5V IOL = 0.5mA VCC = 4.5V IOL = 10.0mA VCC = 5.0V VCC = 5.0V VCC = 5.5V VI = 5.5V VCC = 5.5V VI = 0V VCC = 5.5V VO = 12V
Min. – – – – – 2.4
Max. 20 40 40 60 300
VOH
VOL
“H” output voltage P10 – P14, P20 – P27, P30, P31, R, G, B, OUT, D-A “L” output voltage P10 – P14, P2 0 – P23, P3 0, P31, P40, P41, R, G, B, OUT, D-A “L” output voltage P60 – P63, P0 0 – P07 “L” output voltage P24 – P27 Hysteresis RESET Hysteresis (Note) HSYNC, VSYNC, TIM2, TIM3, INT1, INT2, SIN, SCLK “H” input leak current RESET, P00 – P07, P10 – P17, P2 0 – P27, P30 – P35, P4 0 – P42, H SYNC, VSYNC “L” input leak current RESET, P00 – P07 , P10 – P17, P2 0 – P27, P3 0 – P35, P40 – P42, P6 0 – P63, H SYNC, VSYNC “H” input leak current P60 – P63, P0 0 – P07
VT + – VT–
IIZH
µA µA µA
IIZL IOZH
5 10
Note : P3 2 – P35 , have the hysteresis when these pins are used as interrupt input pins or timer input pins. P40 – P4 2 have the hysteresis when these pins are used as serial I/O ports.
45
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
PACKAGE OUTLINE
46
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–09B < 25C0 > Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37210M3-XXXSP/FP MITSUBISHI ELECTRIC
Date :
Note : Please fill in all items marked g.
Receipt
Section head signature
Supervisor signature
g
)
Customer Date issued Date :
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37210M3-XXXSP M37210M3-XXXFP
Checksum code for entire EPROM EPROM type (indicate the type used)
(hexadecimal notation)
27256
EPROM address 000016 Product name 000F16 100016 15FF16 180016 1DFF16 500016
ROM (12K bytes) ASCII code : ‘M37210M3 –’
Character ROM1
Character ROM2
7FFF16
(1) (2)
Set “FF16” in the shaded area. Write the ASCII codes that indicates the product name of “M37210M3–” to addresses 000016 to 000F16.
g 2. Mark specification Mark specification must be submitted using the correct form for the type package being ordered fill out the appropriate mark specification form (52P4B for M37210M3-XXXSP; 64P6N for M37210M3-XXXFP) and attach to the mask ROM confirmation form. g 3. Comments
(1/3)
signature
Issuance
Company name
TEL (
Submitted by
Supervisor
47
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–09B < 25C0 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37210M3-XXXSP/FP MITSUBISHI ELECTRIC
Writing the product name and character ROM data onto EPROMs
Addresses 000016 to 000F16 store the product name, and addresses 100016 to 15FF16 and addresses 180016 to 1DFF16 store the character pattern. If the name of the product contained in the EPROMs does not match the name on the mask ROM confirmation form, the ROM processing is disabled. Write the data correctly. 1. Inputting the name of the product with the ASCII code ASCII codes ‘M37210M3-’ are listed on the right. The addresses and data are in hexadecimal notation. Address 000016 000116 000216 000316 000416 000516 000616 000716 Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
‘M’ = 4 D ‘3’ = 3 3 ‘7’ = 3 7 ‘2’ = 3 2 ‘1’ = 3 1 ‘0’ = 3 0 ‘M’ = 4 D ‘3’ = 3 3
16 16 16 16 16 16 16 16
‘–’ = 2 D 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16
2. Inputting the character ROM Input the character ROM data by dividing it into character ROM1 and character ROM2. For the character ROM data, see the next page and on.
(2/3)
48
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–09B < 25C0>
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37210M3-XXXSP/FP MITSUBISHI ELECTRIC
The structure of character ROM (divided of 12!16 dots font)
Example Character code “1A16”
Character ROM1
Character ROM2
⇐
Example
11A016 to 11AF16
b7 b6 b5 b4 b3 b2 b1 b0 0 1 2 3 4 5 6 7 8 9 A B C D E F 0016 0416 0416 0A16 0A16 1116 1116 1116 2016 2016 3F16 4016 4016 4016 0016 0016
Example
19A016 to 19AF16
(3/3)
⇐
0 1 2 3 4 5 6 7 8 9 A B C D E F
b7 b6 b5 b4 b3 b2 b1 b0 F016 F016 F016 F016 F016 F016 F016 F016 F816 F816 F816 F416 F416 F416 F016 F016
F16
49
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–10B < 25B0 > Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37210M4-XXXSP MITSUBISHI ELECTRIC
Date :
Note : Please fill in all items marked g.
Receipt
Section head signature
Supervisor signature
g
)
Customer Date issued Date :
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Checksum code for entire EPROM EPROM type (indicate the type used) (hexadecimal notation)
27256
EPROM address 000016 Product name 000F16 100016 15FF16 180016 1DFF16 400016
ROM (16K bytes) ASCII code : ‘M37210M4 –’
Character ROM1
Character ROM2
7FFF16
(1) (2)
Set “FF16” in the shaded area. Write the ASCII codes that indicates the product name of “M37210M4–” to addresses 000016 to 000F16.
g 2. Mark specification Mark specification must be submitted using the correct form for the type package being ordered fill out the appropriate mark specification form (52P4B for M37210M4-XXXSP) and attach to the mask ROM confirmation form. g 3. Comments
(1/3)
50
signature
Issuance
Company name
TEL (
Submitted by
Supervisor
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–10B < 25B0 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37210M4-XXXSP MITSUBISHI ELECTRIC
Writing the product name and character ROM data onto EPROMs
Addresses 000016 to 000F16 store the product name, and addresses 100016 to 15FF16 and addresses 180016 to 1DFF16 store the character pattern. If the name of the product contained in the EPROMs does not match the name on the mask ROM confirmation form, the ROM processing is disabled. Write the data correctly. 1. Inputting the name of the product with the ASCII code ASCII codes ‘M37210M4-’ are listed on the right. The addresses and data are in hexadecimal notation. Address 000016 000116 000216 000316 000416 000516 000616 000716 Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
‘M’ = 4 D ‘3’ = 3 3 ‘7’ = 3 7 ‘2’ = 3 2 ‘1’ = 3 1 ‘0’ = 3 0 ‘M’ = 4 D ‘4’ = 3 4
16 16
16
16 16 16
16
16
‘–’ = 2 D 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16
2. Inputting the character ROM Input the character ROM data by dividing it into character ROM1 and character ROM2. For the character ROM data, see the next page and on.
(2/3)
51
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–10B < 25B0 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37210M4-XXXSP MITSUBISHI ELECTRIC
The structure of character ROM (divided of 12!16 dots font)
Example Character code “1A16”
Character ROM1
Character ROM2
⇐
Example
11A016 to 11AF16
b7 b6 b5 b4 b3 b2 b1 b0 0 1 2 3 4 5 6 7 8 9 A B C D E F 0016 0416 0416 0A16 0A16 1116 1116 1116 2016 2016 3F16 4016 4016 4016 0016 0016
Example
19A016 to 19AF16
(3/3)
52
⇐
0 1 2 3 4 5 6 7 8 9 A B C D E F
b7 b6 b5 b4 b3 b2 b1 b0 F016 F016 F016 F016 F016 F016 F016 F016 F816 F816 F816 F416 F416 F416 F016 F016
F16
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–11B < 25B1 > Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37211M2-XXXSP MITSUBISHI ELECTRIC
Date :
Note : Please fill in all items marked g.
Receipt
Section head signature
Supervisor signature
g
)
Customer Date issued Date :
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Checksum code for entire EPROM EPROM type (indicate the type used) (hexadecimal notation)
27256
EPROM address 000016 Product name 000F16 100016 15FF16 180016 1DFF16 600016
ROM (8K bytes) ASCII code : ‘M37211M2 –’
Character ROM1
Character ROM2
7FFF16
(1) (2)
Set “FF16” in the shaded area. Write the ASCII codes that indicates the product name of “M37211M2–” to addresses 000016 to 000F16.
g 2. Mark specification Mark specification must be submitted using the correct form for the type package being ordered fill out the appropriate mark specification form (52P4B for M37211M2-XXXSP) and attach to the mask ROM confirmation form. g 3. Note (1) (2) Set the stack page selection bit to “0”, because this bit is set to “1” after reset but the internal RAM is located at 0 page only. Both P02 pin (9th pin) and P03 pin (10th pin) are not used as PWM output pins.
g 4. Comments
(1/3)
signature
Issuance
Company name
TEL (
Submitted by
Supervisor
53
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–11B< 25B1 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37211M2-XXXSP MITSUBISHI ELECTRIC
Writing the product name and character ROM data onto EPROMs
Addresses 000016 to 000F16 store the product name, and addresses 100016 to 15FF16 and addresses 180016 to 1DFF16 store the character pattern. If the name of the product contained in the EPROMs does not match the name on the mask ROM confirmation form, the ROM processing is disabled. Write the data correctly. 1. Inputting the name of the product with the ASCII code ASCII codes ‘M37211M2-’ are listed on the right. The addresses and data are in hexadecimal notation. Address 000016 000116 000216 000316 000416 000516 000616 000716 Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
‘M’ = 4 D ‘3’ = 3 3 ‘7’ = 3 7 ‘2’ = 3 2 ‘1’ = 3 1 ‘1’ = 3 1 ‘M’ = 4 D ‘2’ = 3 2
16
16 16 16 16 16 16 16
‘–’ = 2 D 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16
2. Inputting the character ROM Input the character ROM data by dividing it into character ROM1 and character ROM2. For the character ROM data, see the next page and on.
(2/3)
54
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH06–11B < 25B1 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37211M2-XXXSP MITSUBISHI ELECTRIC
The structure of character ROM (divided of 12 !16 dots font)
Example Character code “1A16”
Character ROM1
Character ROM2
Example
11A0 16 0 to 1 11AF 16 2 3 4 5 6 7 8 9 A B C D E F
b7 b6 b5 b4 b3 b2 b1 b0 0016 0416 0416 0A16 0A16 1116 1116 1116 2016 2016 3F16 4016 4016 4016 0016 0016
⇐
⇐
Example 19A0 16 0 to 1 19AF 16 2 3 4 5 6 7 8 9 A B C D E F b7 b6 b5 b4 b3 b2 b1 b0 F016 F016 F016 F016 F016 F016 F016 F016 F816 F816 F816 F416 F416 F416 F016 F016 F16 (3/3)
55
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
56
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
57
MITSUBISHI DATA BOOK SINGLE-CHIP 8-BIT MICROCOMPUTERS Vol.3
Sep. First Edition 1996 H-DF319-B Editioned by Committee of editing of Mitsubishi Semiconductor Data Book Published by Mitsubishi Electric Corp., Semiconductor Division This book, or parts thereof, may not be reproduced in any form without permission o f Mitsubishi Electric Corporation.
REVISION DESCRIPTION LIST
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP, M37210E4-XXXSP/FP, M37210E4SP/FP DATA SHEET
Rev. No. 1.0 2.0 First Edition
Revision Description
Rev. date 9708 971130
Information about copyright note, revision number, release date added (last page).
(1/1)