MMUL310048A

MMUL Series – 5 x 3.2 Custom Oscillator 5 X 3.2 SMT Package – 6 Pins LVPECL Output Tri-state Function RoHS Compliant ELECTRICAL SPECIFICATION: Tape and Reel Packing Available Frequency Range Temperature Stability (Inclusive of Temperature, Load, Voltage, and Aging) Operating Temperature Range Storage Temperature Range Supply Voltage (Vdd) ±5% Supply Current Output Logic “0” Logic “1” Load Symmetry (50% of waveform) Rise/Fall Time (20% to 80%) RMS Phase Jitter (12kHZ to 20MHZ) 74.250MHZ to 161.1328MHZ (See Part Number Guide for Options) (See Part Number Guide for Options) -55°C to +125°C +2.50 VDC 75mA max LVPECL 1.43 VDC typ, 1.60 VDC max 1.10 VDC typ, 0.90 VDC min 50Ω into Vdd-2.0VDC (See Part Number Guide for Options) 300p Sec typ, 700pSec max 1pSec max 100 Hz 1 kHz 10 kHz 100 kHz -95 dBc/Hz -125 dBc/Hz -143 dBc/Hz -146 dBc/Hz Phase Noise Start-up Time Tri-state Operation 10mSec max Voh = 70% of Vdd min or No Connection to Enable Output Vol = 30% max or grounded to Disable Output (High Impedance) PART NUMBER GUIDE: MMU 5 x 3.2 Ceramic SMD 6 Pads L Frequency Supply Voltage Output L=LVPECL 2 = +2.50 VDC 3 = +3.30 VDC Frequency Stability 020 = ±20 ppm 025 = ±25 ppm 050 = ±50 ppm 100 = ±100 ppm Operating Temperature Blank = 0°C to +70°C 27 = -20°C to +70°C 48 = -40°C to +85°C Symmetry Blank = 40%/60% A = 45%/55% Pin 1 Connection Blank = No Connection H = Tri-state Packaging Blank = Bulk T = Tape and Reel Please Consult with MMD Sales Department for any other Parameters or Options MECHANICAL DIMENSIONS: MMD Components, 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com Sales@mmdcomp.com In the event of conflict, the requirements of this specification shall govern. Revisions only with customer approval Page 1 of 2 Revision: Date: MMUL092209A 09/30/09 Release: AWV 5.15 [.203] MAX 2.54 [.100] 1.30 [.051] 1.27 [.050] 4 5 6 1.27 [.050] 2.54 [.100] 0.80 [.031] MXX.XXX SYYMML 3.35 [.132] MAX 1.00 [.039] 3 2 1 1.40 [.055] PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN CONNECTIONS TRI-STATE NO CONNECTION CASE GROUND OUTPUT COMPLEMENTARY OUTPUT SUPPLY VOLTAGE PIN 1 DESIGNATOR LOCATED IN THIS AREA. 0.64 [.025] 1.00 [.039] DIMENSION IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR IS RECOMMENDED RECOMMENDED LAND PATTERN ENVIRONMENTAL/MECHANICAL SPECIFICATION: MARKING DETAIL: Line 1: MXX.XXX XX.XXX = Frequency in MHz Line 2: SYMCCL S = Internal Code YM = Date Code (Year/Month) CC = Crystal Parameters Code L = Denotes RoHS Compliant Shock Solderability Vibration Gross Leak Test Fine Leak Test Reflow Solder MIL-STD-883, Meth 2002, Cond MIL-STD-883, Meth 2003 MIL-STD-883, Meth 2007, Cond MIL-STD-883, Meth 1014, Cond MIL-STD-883, Meth 1014, Cond +260ºC for 10 sec max B A C A TAPE AND REEL DIMENSIONS: PITCH TAPE WIDTH REEL DIA Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PITCH TAPE WIDTH REEL DIA QTY PER REEL PIN 1 ORIENT. 8.0 [.315] 16.0 [.630] 330 [13 IN] 1000 Q1 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters [inches]. 3. Tolerances are ±0.1 [.004] unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD Components, 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com Sales@mmdcomp.com ` In the event of conflict, the requirements of this specification shall govern. Revisions only with customer approval Page 2 of 2 Release: AWB Revision: Date: MMUL092209A 09/30/09