0002065108

12 H 10 11 PART NO. ENG. NO. 02-06-1101 02-06-1103 02-06-5101 02-06-5102 02-06-5108 02-06-5109 02-06-5100 02-06-5103 NOT TOOLED 1561-(P901) 1561-(P901)L 1561-(P561) 1561-(P561)L 1561-(P228) 1561-(P228)L 1561-(P550) 1561-(P550)L 1561-1(P901)L 9 7 8 5 6 4 3 2 1 H (3.20) .126 C L G G (.25) MAX. .010 CARRIER CUTOFF (1.50/1.42) "A" DIA. .059/.056 (3.56/2.79) (2.74/2.16) .140/.110 .108/.085 GAP ACCEPTABLE SEE ALTERNATE TIP VIEW (16.8) F SELECT GOLD PLATE DEPTH (WHEN SPECIFIED) (25.40) 1.000 F .66 (2.03) .080 (3.56) .140 SECT. "B-B" CARRIER VIEW ACTUAL SIZE OPTIONAL LOCKING TAB (2 PL.) SEE LEGEND SECT. "C-C" SCALE:10X SCALE:10X E E (2.03) .080 1561-✴(✴✴✴✴)✴ BLANK=WITH LOCKING TABS D "C" FORM BLANK=CHAIN L=LOOSE 1=WITHOUT LOCKING TABS FINISH CODE P=PREPLATE BLANK=POSTPLATE "B" "B" LEGEND "C" D (.25) MAX. .010 CARRIER CUTOFF "A" C L (1.52) (.38) .060 .015 SECT. "A-A" C B A C NOTES: 1. MATERIAL: BRASS 2. FINISH: 901 HOT TIN DIP (.00051)/.000020 MIN. 228 SELECT GOLD PLATE (.00075)/.000030 MIN. IN CONTACT AREA, SELECT TIN. (.00250)/.000100 MIN. IN CRIMP AREA OVER (.00125)/.000050 MIN. NICKEL OVERALL. 561 SELECT GOLD PLATE (.00076)/.000030 MIN. IN CONTACT AREA, OVER (.00127)/.000050 MIN. NICKEL OVERALL. 591 SELECT GOLD PLATE (.00175)/.000050 MIN. IN CONTACT AREA, OVER (.00127)/.000050 MIN. NICKEL OVERALL WITH (.000025)/.000010 MAX. GOLD FLASH OVERALL. 550 SELECT GOLD PLATE (.00038)/.000015 MIN. IN CONTACT AREA, OVER (.00076)/.000030 MIN. NICKEL OVERALL WITH (.000025)/.000010 MAX. GOLD FLASH OVERALL. 3. PRODUCT SPECIFICATION: PS-02-06. 4. PACKAGING INFORMATION: LOOSE TERMINALS: PK-1190-003 CHAIN TERMINALS: 15610000-PK 5. TERMINAL FOR USE WITH (1.57)/.062 DIA. SERIES HOUSINGS AND WILL ACCEPT 18 THRU 24 AWG WIRE WITH (1.52/3.05)/.060/.120 INSULATION DIA. 6. PARTS CONFORM TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 7. TIP GEOMETRY IS TOOL DEPENDENT. EITHER GEOMETRY IS ACCEPTABLE. DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: E1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/05/24 10 ALTERNATE TIP GEOMETRY SEE NOTE 7 B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509988 = = NTS 0 MM/IN 0 GENERAL TOLERANCES (UNLESS SPECIFIED) MM = 0 INCH 4 PLACES ± ± 3 PLACES ± ± 0.01 DIVISIONAL SYMBOLS 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± 1 PLACE 0 PLACES ± ANGULAR TOL ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:34:33 9 8 7 6 5 EC NO: 704776 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: GEW APPR: GWF THIRD ANGLE PROJECTION 4 2022/03/24 2022/05/24 2022/05/24 CRIMP TERMINAL, FEMALE .062 DIA. FOR 18-24 AWG WIRE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1991/02/19 1991/02/19 DRAWING SERIES C-SIZE 1561 3 SD-1561-X MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 AP4 SHEET NUMBER 1 OF 1 1 A