0008560105

19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 L L CHAIN, PER WINDING DETAIL "A" CHAIN, PER WINDING DETAIL "B" K K FINISH: (P909) OVERALL HOT TIN DIP: (0.00254)/.000100 MIN. (122) OVERALL TIN: (0.00381)/.000150 MIN. OVER (0.00076)/.000030 MIN. NICKEL (154) OVERALL TIN: (0.00254)/.000100 MIN. J J OVER (0.00127)/.000050 MIN. NICKEL (224) OVERALL MATTE TIN: (0.00508/.000200 MIN. OVER (0.00127)/.000050 MIN. NICKEL (550) SELECT GOLD: (0.00038)/.000015 MIN. OVERALL GOLD FLASH: (0.00005)/.000002 MIN. OVERALL NICKEL UNDERPLATE: (0.00076)/.000030 MIN. H H (555) SELECT GOLD: (0.00038)/.000015 MIN. OVERALL NICKEL UNDERPLATE: (0.00076)/.000030 MIN. (558) SELECT GOLD: (0.00076)/.000030 MIN. OVERALL GOLD FLASH: (0.00005)/.000002 MIN. OVERALL NICKEL UNDERPLATE: (0.00127)/.000050 MIN. (561) SELECT GOLD: (0.00076)/.000030 MIN. G G OVERALL NICKEL UNDERPLATE: (0.00127)/.000050 MIN. (591) SELECT GOLD: (0.00127)/.000050 MIN. OVERALL GOLD FLASH: (0.00005)/.000002 MIN. OVERALL NICKEL UNDERPLATE: (0.00127)/.000050 MIN. F F E E D D NOTES: 1. MATERIAL: SEE LEGEND C 2. FINISH: SEE LEGEND C 3. PRODUCT SPECIFICATION PS-08-50. 4. PACKAGING SPECIFICATION: LOOSE TERMINALS: PER PK-2759-001 CHAIN FORM TERMINALS: PK-2759-002 SYMBOLS 5. DIMENSIONS GIVEN ACROSS CENTERLINES ARE SYMMETRICAL ABOUT THOSE = 0 CENTERLINES WITHIN HALF THE TOTAL TOLERANCE. B 6. (0.86 ±0.05)/.034 ±.002 IS AN OPTIONAL DESIGN. = 0 7. CRIMP ACCEPTS 18 TO 24 AWG WIRE WITH (2.79)/.110 MAX. INSULATION DIAMETER. = 0 AND CAN ACCEPT (3.00)/.118 MAX. INSULATION DIAMETER WITH SPECIAL TOOLING. = 0 8. TERMINAL FOR USE IN 2139, 3001, 3069, AND 91813 SERIES HOUSINGS WITH (2.54)/.100 MAX. INSULATION DIAMETER, = 0 2574, 6422, AND 5239 SERIES HOUSINGS WITH (2.79)/.110 MAX. INSULATION DIAMETER, AND 41695 SERIES HOUSING WITH (3.00)/.118 MAX. INSULATION DIAMETER. A 9. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) MM FORMAT: Eng-lega-master-tb-prod-D REVISION: D DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/10/05 ± 3 PLACES ± ± 16 C 15 14 13 12 11 10 9 8 0.01 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± = 0 1 PLACE = 0 0 PLACES ± ANGULAR TOL 09:56:20 INCH 4 PLACES ± = 0 DOCUMENT STATUS CURRENT REV DESC: NOTE 4 UPDATED ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS = 0 7 6 B EC NO: 605479 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: SAMIEC APPR: FSMITH THIRD ANGLE PROJECTION 5 CRIMP TERMINAL .156 CENTERS 18 TO 24 GA WIRE 2018/09/20 2018/10/05 2018/10/05 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1986/06/03 2012/03/20 DRAWING SERIES D-SIZE 2478 4 SD-2478 MATERIAL NUMBER SEE CHART 3 PSD 001 Y2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 1 OF 2 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 L L 2478-1C-(154) 2478-1C-(154)L 2478-3C-(154) 2478-3C-(154)L K K 2478-3-(154) 2478-3-(154)L 2478-1-(154) 2478-1-(154)L J J H H G G F F E E D D C C SYMBOLS = 0 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN 1:1 = 0 B GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 = 0 = 0 A MM ± 3 PLACES ± ± FORMAT: Eng-lega-master-tb-prod-D REVISION: D DATE: 2018/01/18 19 18 RELEASE DATE 17 2018/10/05 16 09:56:20 C 15 14 13 12 11 10 9 8 0.01 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± = 0 1 PLACE = 0 0 PLACES ± = 0 P1 INCH 4 PLACES ± ANGULAR TOL DOCUMENT STATUS CURRENT REV DESC: NOTE 4 UPDATED ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS = 0 7 6 B EC NO: 605479 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: SAMIEC APPR: FSMITH THIRD ANGLE PROJECTION 5 CRIMP TERMINAL .156 CENTERS 18 TO 24 GA WIRE 2018/09/20 2018/10/05 2018/10/05 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1986/06/03 2012/03/20 DRAWING SERIES D-SIZE 2478 4 SD-2478 MATERIAL NUMBER SEE CHART 3 PSD 001 Y2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 2 OF 2 1 A