0022192048

12 11 10 9 8 7 5 6 4 3 2 1 NOTES: 1. MATERIAL: NYLON, UL94V-0, COLOR: WHITE 2. FINISH: (197) OVERALL REFLOWED MATTE TIN: 0.00152/.000060 MIN. OVER 0.00127/.000050 MIN. NICKEL OVERALL. (228) SELECT GOLD: 0.00076/.000030 MIN. SELECT TIN: 0.00254/.000100 MIN. OVERALL NICKEL UNDERPLATE: 0.00127/.000050 MIN. (241) SELECT GOLD: 0.00051/.000020 MIN. SELECT TIN: 0.00254/.000100 MIN. OVERALL NICKEL UNDERPLATE: 0.00127/.000050 MIN. 3. PARTS CONFORM TO PRODUCT SPECIFICATION PS-10-07. 4. PACKAGING INFORMATION: SEE LEGEND. 5. PARTS ARE STACKABLE END TO END ON .100/(2.54) CENTERS. 6. PIN PUSH OUT FORCE: 2 LBS. MIN. 7. CIRCUIT ONE DESIGNATION IS USED TO DEFINE VOID LOCATION. CIRCUIT ONE MAY OR MAY NOT LINE UP WITH CIRCUIT ONE ON THE MATING HOUSING. 8. PARTS CONFORM TO CLASS 'B' REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. H G A B H G F F /(0.20) G GOLD E E GROOVE MAY OR MAY NOT BE PRESENT (BOTH SIDES). GEOMETRY IS TOOL DEPENDENT AND MAY BE SLIGHTLY DIFFERENT THAN SHOWN RECESSED GATE MAY BE PRESENT ON 2-25 CKT PARTS. LOCATION VARIES T TIN 7 D D /(0.13) C C TUBE LENGTH BULK PK-7478-001 TUBE: PK-44743-001 B 22.047/(560.00) B = 0 = 0 = 0 FORMAT: Eng-lega-master-tb-prod-C REVISION: B DATE: 2015/11/19 12 C RELEASE DATE 11 10 9 8 7 6 = 0 = 0 = 0 U3 5 REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: = A 2016/03/16 2017/04/11 2017/04/28 0 111298 MKIPPER MKIPPER FSMITH PLATING: SEE NOTE 2. = ADD ALT ENGRAVING VIEW QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES (UNLESS SPECIFIED) INCH MM --- IN/MM DRWN BY 4 PLACES ± ± MKIPPER 3 PLACES ± ± .010 CHK'D BY 2 PLACES ± 0.25 ± .015 SAMIEC 1 PLACES ± 0.36 ± APPR BY 0 PLACES ± ± FSMITH ANGULAR TOL ± 1/2 DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DATE 2014/04/07 DATE FRICTION LOCK HEADER ASY .100 CL. BENT SQ. PINS 7832 SERIES DWG. W/VOIDS 98/10/09 DATE PRODUCT CUSTOMER DRAWING 2014/08/06 THIRD ANGLE PROJECTION C SERIES MATERIAL NUMBER 7832 SEE CHART GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER DOCUMENT NUMBER SDA-7832 3 CUSTOMER 2 PSD 1 OF 3 000 1 A 12 11 10 9 8 7 5 6 4 3 2 1 DIM. G DIM. T H H .264 (6.71) .141 (3.58) .120 (3.05) .046 (1.17) N/A OVERALL N/A OVERALL A-7832-NA197 42663-0662 .740 (18.80) A-7832-NB197 42663-0742 .780 (19.81) .305 (7.75) .140 (3.56) .120 (3.05) .046 (1.17) A-7832-NA241 42663-0666 .740 (18.80) .264 (6.71) .141 (3.58) .120 (3.05) .046 (1.17) A-7832-NA228 42663-0664 .740 (18.80) .264 (6.71) .141 (3.58) .120 (3.05) .046 (1.17) .180 (4.57) .180 (4.57) .135 (3.43) .135 (3.43) G G F F ALTERNATE ENGRAVING LOCATION (7-12 CKT PARTS ONLY). LOCATION IS DEPENDENT ON TOOLING. E E D D C C B B = 0 = 0 = 0 FORMAT: Eng-lega-master-tb-prod-C REVISION: B DATE: 2015/11/19 12 P1 RELEASE DATE 11 28.04.2017 C 22:16:24 10 9 8 7 6 = 0 = 0 = 0 U3 5 REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: = A 111298 MKIPPER MKIPPER FSMITH 0 SEE SHEET 1 = 2016/03/16 2017/04/11 2017/04/28 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES (UNLESS SPECIFIED) IN/MM INCH MM DRWN BY 4 PLACES ± ± MKIPPER 3 PLACES ± ± .010 CHK'D BY 2 PLACES ± 0.25 ± .015 SAMIEC 1 PLACES ± 0.36 ± APPR BY 0 PLACES ± ± FSMITH ANGULAR TOL ± 1/2 DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 NTS DATE 2014/04/07 DATE FRICTION LOCK HEADER ASY .100 CL. BENT SQ. PINS 7832 SERIES DWG. W/VOIDS 98/10/09 DATE PRODUCT CUSTOMER DRAWING 2014/08/06 THIRD ANGLE PROJECTION C SERIES MATERIAL NUMBER 7832 SEE CHART GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER DOCUMENT NUMBER SDA-7832 3 CUSTOMER 2 PSD 2 OF 3 000 1 A 12 11 10 9 A-7832-NA197-* G F E A-7832-14A197-51 A-7832-17A197-51 A-7832-3A197-2 46999-0581 46999-0651 7 5 6 A-7832-NB197-* A-7832-5A197-2 A-7832-19A197-14 A-7832-6A197-2 A-7832-7A197-4 A-7832-7A197-5 A-7832-6A197-5 A-7832-4A197-2 A-7832-7A197-3 A-7832-11A197-6 A-7832-5A197-4 A-7832-25A197-1 A-7832-12A197-10 A-7832-15A197-14 A-7832-12A197-4 A-7832-4A197-3 A-7832-8A197-4 A-7832-11A197-51 A-7832-16A197-51 A-7832-8A197-2 A-7832-8A197-6 A-7832-8A197-7 A-7832-10A197-2 A-7832-10A197-9 A-7832-8A197-3 A-7832-27A197-51 H 8 4 3 A-7832-NA241-* A-7832-10B197-6 A-7832-7B197-4 2 1 A-7832-NA228-* A-7832-7A241-6 A-7832-6A241-3 A-7832-9A241-6 A-7832-9A228-3 A-7832-9A228-4 A-7832-4A228-3 H G F E 3,6,12,15 2 D D C C B B = 0 = 0 = 0 FORMAT: Eng-lega-master-tb-prod-C REVISION: B DATE: 2015/11/19 12 P1 RELEASE DATE 11 28.04.2017 C 22:16:24 10 9 8 7 6 = 0 = 0 = 0 U3 5 REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: = A 111298 MKIPPER MKIPPER FSMITH 0 SEE SHEET 1 = 2016/03/16 2017/04/11 2017/04/28 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES (UNLESS SPECIFIED) IN/MM INCH MM DRWN BY 4 PLACES ± ± MKIPPER 3 PLACES ± ± .010 CHK'D BY 2 PLACES ± 0.25 ± .015 SAMIEC 1 PLACES ± 0.36 ± APPR BY 0 PLACES ± ± FSMITH ANGULAR TOL ± 1/2 DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 NTS DATE 2014/04/07 DATE FRICTION LOCK HEADER ASY .100 CL. BENT SQ. PINS 7832 SERIES DWG. W/VOIDS 98/10/09 DATE PRODUCT CUSTOMER DRAWING 2014/08/06 THIRD ANGLE PROJECTION C SERIES MATERIAL NUMBER 7832 SEE CHART GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER DOCUMENT NUMBER SDA-7832 3 CUSTOMER 2 PSD 3 OF 3 000 1 A