0150150827

13 G F E D C LENGTH WIDTH 23 2.00 [50.8] .283 [7.2] 150150423 23 4.00 [101.6] .283 [7.2] 150150623 23 6.00 [152.4] .283 [7.2] 150150823 23 8.00 [203.2] .283 [7.2] 150151023 23 10.00 [254.0] .283 [7.2] 150150225 25 2.00 [50.8] .307 [7.8] 150150425 25 4.00 [101.6] .307 [7.8] 150150625 25 6.00 [152.4] .307 [7.8] 150150825 25 8.00 [203.2] .307 [7.8] 150151025 25 10.00 [254.0] .307 [7.8] 150150227 27 2.00 [50.8] .331 [8.4] 150150427 27 4.00 [101.6] .331 [8.4] 150150627 27 6.00 [152.4] .331 [8.4] 150150827 27 8.00 [203.2] .331 [8.4] 150151027 27 10.00 [254.0] .331 [8.4] 150150229 29 2.00 [50.8] .354 [9.0] 150150429 29 4.00 [101.6] .354 [9.0] 150150629 29 6.00 [152.4] .354 [9.0] 150150829 29 8.00 [203.2] .354 [9.0] 150151029 29 10.00 [254.0] .354 [9.0] 150150233 33 2.00 [50.8] .403 [10.2] 150150433 33 4.00 [101.6] .403 [10.2] 150150633 33 6.00 [152.4] .403 [10.2] 150150833 33 8.00 [203.2] .403 [10.2] 150151033 33 10.00 [254.0] .403 [10.2] 150150239 39 2.00 [50.8] .472 [12.0] 150150439 39 4.00 [101.6] .472 [12.0] 150150639 39 6.00 [152.4] .472 [12.0] 150150839 39 8.00 [203.2] .472 [12.0] 150151039 39 10.00 [254.0] .472 [12.0] 150150245 45 2.00 [50.8] .543 [13.8] 150150445 45 4.00 [101.6] .543 [13.8] 150150645 45 6.00 [152.4] .543 [13.8] 150150845 45 8.00 [203.2] .543 [13.8] 150151045 45 10.00 [254.0] .543 [13.8] 150150251 51 2.00 [50.8] .614 ]15.6] 150150451 51 4.00 [101.6] .614 ]15.6] 150150651 51 6.00 [152.4] .614 ]15.6] PART NO. CIRCUITS 150150223 150150851 51 8.00 [203.2] .614 ]15.6] 150151051 51 10.00 [254.0] .614 ]15.6] 9 8 7 6 .0118 [.30] J H WIDTH G .0118 [.30] .0118 [.30] x (N+1) x (N-1) F FRONT TAIL STIFFENER BOTH ENDS E R.008 [R.20] TYP. (4) D N = NUMBER OF CONDUCTORS JUMPER END DETAIL 33 CIRCUIT SHOWN C REAR UPDATED NOTE 5 PART NUMBER CONSTRUCTION B 10 1 .0118 [.30] GENERAL TOLERANCES (UNLESS SPECIFIED) 11 2 EXPOSED CIRCUITS BOTH ENDS (NOTE 4) A 12 3 LENGTH NUMBER OF CIRCUITS LENGTH SERIES NUMBER 13 4 I 15015 _ _ _ _ B 5 NOTES: 1. SUBSTRATE AND COVERLAY MATERIAL IS .001 [25uM] POLYIMIDE. 2. CONDUCTOR IS 1/2 OZ (.0007) [18uM] COPPER. 3. PLATING IS 2 MICRO INCHES MINIMUM OF HARD GOLD OVER 100 MICRO INCHES MINIMUM OF NICKEL. 4. TAIL ENDS ARE .008 [.20] THICK. 5. JUMPER CABLES ARE SUITABLE FOR USE WITH MOLEX 502598 SERIES CONNECTOR. 9 8 =0 DESCRIPTION H 10 C =0 4 PLACES 3 PLACES 2 PLACES 1 PLACE mm INCH --------- --.010 .030 --- DIMENSION STYLE SCALE DESIGN UNITS INCH [MM] NONE METRIC DRAWN BY DATE CHECKED BY DATE APPROVED BY DATE 1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS REV I 11 EC NO: J 12 7 6 5 MATERIAL NO. TITLE C Molex MOLEX INCORPORATED SHEET NO. DOCUMENT NO. SD-15015-001 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INCORPORATED AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 4 B .3MM PITCH JUMPER CABLES SEE CHART SIZE THIRD ANGLE PROJECTION 3 2 1 A