0150311035

12 11 10 9 8 7 6 5 0.30MM CENTER FFC JUMPER CABLE CHART 10 ± .20 INCHES 254 ± 5 MM 12 ± .20 INCHES 305 ± 5 MM 150310807 150311007 150311207 150310609 150310809 150311009 150311209 150310411 150310611 150310811 150311011 150311211 150310215 150310415 150310615 150310815 150311015 150311215 G CKTS: 21 150310221 150310421 150310621 150310821 150311021 150311221 CKTS: 25 150310225 150310425 150310625 150310825 150311025 150311225 CKTS: 31 150310231 150310431 150310631 150310831 150311031 150311231 CKTS: 33 150310233 150310433 150310633 150310833 150311033 150311233 CKTS: 35 150310235 150310435 150310635 150310835 150311035 150311235 F CKTS: 37 150310237 150310437 150310637 150310837 150311037 150311237 CKTS: 39 150310239 150310439 150310639 150310839 150311039 150311239 CKTS: 41 150310241 150310441 150310641 150310841 150311041 150311241 CKTS: 51 150310251 150310451 150310651 150310851 150311051 150311251 CKTS: 61 150310261 150310461 150310661 150310861 150311061 150311261 H "A" DIM. 2 ± .08 INCHES 51 ± 2 MM 4 ± .16 INCHES 102 ± 4 MM 6 ± .16 INCHES 152 ± 4 MM CKTS: 7 150310207 150310407 150310607 CKTS: 9 150310209 150310409 CKTS: 11 150310211 CKTS: 15 8 ± .20 INCHES 203 ± 5 MM 4 3 2 1 NOTES: 1. SUBSTRATE AND COVERLAY MATERIAL IS .001" [25uM] POLYIMIDE. 2. CONDUCTOR IS 1/2 OZ (.0007") [18um] COPPER. 3. PLATING IS 2 MICRO INCHES MINIMUM OF HARD GOLD OVER 100 MICRO INCHES MINIMUM OF NICKEL. 4. TAIL ENDS ARE .008±.001 [0.20±0.03] THICK. 5. JUMPER CABLES ARE SUITABLE FOR USE WITH MOLEX 504754 SERIES CONNECTOR. N = NUMBER OF CONDUCTORS G .053±.004 [1.35±0.10] .030±.004 [.75±0.10] .026±.004 [.65±0.10] .006 [.15] MAX .026±.003 [.65±0.07] F .008 [.20] TYP .004 .0118X(N+1)-.004±.002 [0.3X(N+1)-0.1±0.05] E E [.10] MAX .012+.002 -.001 .30+0.04 -0.03 [ .0118X(N+3)+.004±.002 [0.3X(N+3)+0.1±0.05] .0118X(N-1)±.001 [0.3X(N-1)±0.03] "A" .079±.012 [2.00±0.30] EXPOSED CIRCUITS BOTH ENDS (NOTE 4) R.008±.002 [R.20±0.05] (2X) R.004±.002 [R.10±0.05] (8X).022±.002 [.55±0.05] (2X) TOP ] .012 [.30] PITCH D C H D C .037±.002 [.95±0.05] (2X) JUMPER END DETAIL 25 CIRCUIT SHOWN (SCALE 10:1) B FUNCTIONAL SYMBOLS .118±.020 [3.00±0.50] BOTTOM STIFFENER BOTH ENDS =0 =0 =0 BOTTOM THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/INCH 4:1 mm ± ---- 3 PLACES ± ---- ± 0.01 P1 23:34:44 RELEASE DATE 2022/03/30 11 10 ± 0.03 ± ---- ± ---- 0 PLACES ± ---- ± ---- ANGULAR TOL ± DOCUMENT STATUS 12 INCH 4 PLACES ± ---- 1 PLACE FORMAT: IN-ACAD-tb-prod-C REVISION: A1 DATE: 2019/06/12 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 9 8 7 6 CURRENT REV DESC: PRODUCTION RELEASE GENERAL TOLERANCES (UNLESS SPECIFIED) DIVISIONAL SYMBOLS 2 PLACES ± ---- A B 5 .3MM PITCH EC NO: 701160 DRWN: MIMIG CHK'D: JSMITH11 APPR: JSMITH11 INITIAL REVISION: DRWN: MIMIG APPR: JSMITH11 THIRD ANGLE PROJECTION 4 2022/03/28 2022/03/30 2022/03/30 JUMPER CABLES PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2022/03/28 2022/03/30 DRAWING SERIES C-SIZE 15031 3 DOC TYPE DOC PART REVISION 150310001 MATERIAL NUMBER PSD 000 CUSTOMER SEE CHART 2 A SHEET NUMBER GENERAL MARKET 1 OF 1 1 A