0190670129

PRODUCT SPECIFICATION NYLAKRIMP RINGS 1.0 SCOPE A. THIS PRODUCT SPECIFICATION COVERS THE NYLAKRIMP RINGS WITH NYLON INSULATION AND TIN PLATING FOR 8 AWG TO 4/0 AWG WIRE. 2.0 PRODUCT DESCRIPTION 2.1 INSULATED RING TERMINALS A. 19067 NYLAKRIMP BRAZED RINGS 8 – 4/0 AWG 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS A. THE DIMENSIONAL CHARACTERISTICS ARE IDENTIFIED ON THE SALES DRAWINGS. B. MATERIALS: I. BASE MATERIAL IS C11000 COPPER IN VARIOUS THICKNESSES. II. PLATING IS MATTE TIN .000100(0.00254) MINIMUM THICKNESS. III. INSULATION MATERIAL IS NYLON IN VARIOUS COLORS. 2.3 SAFETY AGENCY APPROVALS A. 8 AWG THROUGH 4/0 AWG PARTS ARE UL LISTED E32244 CATEGORY ZMVV B. 8 AWG THROUGH 1/0 AWG PARTS ARE CSA CERTIFIED LR18689 CLASS 6223-02 C. ALL PARTS ARE ROHS COMPLIANT 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS A. UL LISTED TO STANDARD 486A & B B. CSA CERTIFIED TO STANDARD C22.2 NO 65 4.0 RATINGS 4.1 VOLTAGE A. ALL UL/CSA LISTED PARTS UNDER THIS SPEC ARE RATED AT 600VAC. REVISION: A ECR/ECN INFORMATION: EC No: WNA2010-0414 DATE: 2011 / 08 / 01 DOCUMENT NUMBER: PS-19902-016 TITLE: PRODUCT SPECIFICATIONNYLAKRIMP RING TERMINALS SHEET No. 1 of 3 CREATED / REVISED BY: CHECKED BY: APPROVED BY: E. THRODAHL J. MACNEIL J. MACNEIL TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 4.2 CURRENT A. THE AMPERAGE RATING IS BASED ON THE WIRE AWG APPLIED TO THE TERMINALS PER UL 486 A & B SHOWN BELOW. WIRE AWG 8 6 4 2 1 1/0 2/0 3/0 4/0 4.3 TEMPERATURE A. OPERATING - MAX AMPERE RATING 50 65 85 115 130 150 175 200 230 105°C (221°F) 4.4 FLAMMABILITY A. ALL PARTS UNDER THIS SPECIFICATION HAVE NYLON INSULATION WITH UL FLAMMABILITY RATING OF 94V-2. REVISION: A ECR/ECN INFORMATION: EC No: WNA2010-0414 DATE: 2011 / 08 / 01 DOCUMENT NUMBER: PS-19902-016 TITLE: PRODUCT SPECIFICATIONNYLAKRIMP RING TERMINALS SHEET No. 2 of 3 CREATED / REVISED BY: CHECKED BY: APPROVED BY: E. THRODAHL J. MACNEIL J. MACNEIL TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 1 Temperature Rise as a result of Current Cycling* 2 Static Heating Sequence Static Heating* 3 Static Heating Sequence Secureness* The Test Samples, with correct conductor The Test Samples must be length, are fastened thru a bushing, at the intact at the transition area height indicated and with a mass after 30 minutes. suspended from the free end per Table 26*. 4 Static Heating Sequence – Pullout* The Test Samples from Secureness Test are subjected to a Direct Axial Pull with a Force Applied per Table 27* The Test Specimens shall complete 500 cycles of equal current on and off (1 hr ea.) at the current levels noted in Table 7 for 75C*. The Test Samples must carry continuous current as noted in Table 7* until stabilization. Temperature Rise must not exceed 125C over Ambient Temperature Rise must not exceed 50C over Ambient The Test Samples must withstand Table 27* Force applied for 1 minute 5.2 MECHANICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5 Wire Pullout Force* (Axial) Test Samples Crimped to Min/Max wire awg are subjected to an axial pullout force on the wire at a rate of 25 ± 6 mm (1 ± ¼ inch) per minute. The Test Samples must withstand Table 27* Force applied for 1 minute * See UL Standard 486A & B for Test Descriptions and Table information 6.0 PACKAGING Parts shall be packaged to protect against damage during handling, transit and storage. REVISION: A ECR/ECN INFORMATION: EC No: WNA2010-0414 DATE: 2011 / 08 / 01 DOCUMENT NUMBER: PS-19902-016 TITLE: PRODUCT SPECIFICATIONNYLAKRIMP RING TERMINALS SHEET No. 3 of 3 CREATED / REVISED BY: CHECKED BY: APPROVED BY: E. THRODAHL J. MACNEIL J. MACNEIL TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC