0190710340

PRODUCT SPECIFICATION INSULKRIMP RINGS AND SPADES 1.0 SCOPE A. THIS PRODUCT SPECIFICATION COVERS THE INSULKRIMP RINGS AND SPADES WITH PVC INSULATION AND TIN PLATING FOR 22 AWG TO 3/0 AWG WIRE. 2.0 PRODUCT DESCRIPTION 2.1 INSULATED RINGS AND SPADES A. 19054 INSULKRIMP LONG BARREL RINGS 22 – 14 AWG B. 19055 INSULKRIMP BRAZED LONG BARREL RINGS 22 – 14 AWG C. 19070 INSULKRIMP RINGS 22 – 10 AWG D. 19071 INSULKRIMP BRAZED RINGS 8 – 3/0 AWG E. 19075 INSULKRIMP STAR RINGS 22 – 14 AWG F. 19080 INSULKRIMP MULTI STUD RINGS 22 – 10 AWG G. 19089 INSULKRIMP LONG BARREL RECTANGULAR TONGUE 22 – 14 AWG H. 19090 INSULKRIMP RECTANGULAR TONGUE 22 – 10 AWG I. 19099 INSULKRIMP SNAP SPADES 22 – 10 AWG J. 19119 INSULKRIMP LONG BARREL FLANGED SPADES 22 – 14 AWG K. 19120 INSULKRIMP BRAZED LONG BARREL FLANGED SPADES 22 – 14 AWG L. 19121 INSULKRIMP FLANGED SPADES 22 – 10 AWG M. 19122 INSULKRIMP BRAZED FLANGED SPADES 22 – 10 AWG N. 19130 INSULKRIMP LONG BARREL BLOCK SPADES 22 – 14 AWG O. 19131 INSULKRIMP BLOCK SPADES 22 – 10 AWG P. 19142 INSULKRIMP LONG BARREL SPADES 22 – 14 AWG Q. 19143 INSULKRIMP BRAZED LONG BARREL SPADES 22 – 14 AWG R. 19144 INSULKRIMP SPADES 22 – 10 AWG S. 19145 INSULKRIMP BRAZED SPADES 22 – 10 AWG T. 19171 INSULKRIMP LONG BARREL HOOKS 22 – 14 AWG U. 19179 INSULKRIMP HOOKS 22 – 10 AWG V. 19204 INSULKRIMP 3 & 4 WAY RINGS 22 – 10 AWG 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS A. THE DIMENSIONAL CHARACTERISTICS ARE IDENTIFIED ON THE SALES DRAWINGS. B. MATERIALS: I. BASE MATERIAL IS C11000 COPPER IN VARIOUS THICKNESSES. II. PLATING IS MATTE TIN .000100(0.00254) MINIMUM THICKNESS. III. INSULATION MATERIAL IS PVC IN VARIOUS COLORS. 2.3 SAFETY AGENCY APPROVALS A. 22 AWG THROUGH 1/0 AWG PARTS ARE UL LISTED E32244 CATEGORY ZMVV B. 22 AWG THROUGH 2 AWG PARTS ARE CSA CERTIFIED LR18689 CLASS 6223-02 C. ALL PARTS ARE ROHS COMPLIANT REVISION: C ECR/ECN INFORMATION: EC No: WNA2010-0414 DATE: 2011 / 08 / 01 DOCUMENT NUMBER: PS-19902-009 TITLE: PRODUCT SPECIFICATIONINSULKRIMP RING AND SPADE TERMINALS SHEET No. 1 of 3 CREATED / REVISED BY: CHECKED BY: APPROVED BY: E. THRODAHL J. MACNEIL J. MACNEIL TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS A. 22 THROUGH 1/0 AWG UL LISTED TO STANDARD 486A & B B. 22 THROUGH 2 AWG CSA CERTIFIED TO STANDARD C22.2 NO 65 4.0 RATINGS 4.1 VOLTAGE A. ALL UL/CSA LISTED PARTS UNDER THIS SPEC ARE RATED AT 600VAC. 4.2 CURRENT A. THE AMPERAGE RATING IS BASED ON THE WIRE AWG APPLIED TO THE TERMINALS PER UL 486 A & B SHOWN BELOW. WIRE AWG 22 20 18 16 14 12 10 8 6 4 2 1 1/0 4.3 TEMPERATURE A. OPERATING - MAX AMPERE RATING 15 20 30 50 65 85 115 130 150 105°C (221°F) 4.4 FLAMMABILITY A. ALL PARTS UNDER THIS SPECIFICATION HAVE PVC INSULATION WITH UL FLAMMABILITY RATING OF 94V-0. REVISION: C ECR/ECN INFORMATION: EC No: WNA2010-0414 DATE: 2011 / 08 / 01 DOCUMENT NUMBER: PS-19902-009 TITLE: PRODUCT SPECIFICATIONINSULKRIMP RING AND SPADE TERMINALS SHEET No. 2 of 3 CREATED / REVISED BY: CHECKED BY: APPROVED BY: E. THRODAHL J. MACNEIL J. MACNEIL TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 1 Temperature Rise as a result of Current Cycling* 2 Static Heating Sequence Static Heating* 3 Static Heating Sequence Secureness* The Test Samples, with correct conductor The Test Samples must be length, are fastened thru a bushing, at the intact at the transition area height indicated and with a mass after 30 minutes. suspended from the free end per Table 26*. 4 Static Heating Sequence – Pullout* The Test Samples from Secureness Test are subjected to a Direct Axial Pull with a Force Applied per Table 27* The Test Specimens shall complete 500 cycles of equal current on and off (1 hr ea.) at the current levels noted in Table 7 for 75C*. The Test Samples must carry continuous current as noted in Table 7* until stabilization. Temperature Rise must not exceed 125C over Ambient Temperature Rise must not exceed 50C over Ambient The Test Samples must withstand Table 27* Force applied for 1 minute 5.2 MECHANICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5 Wire Pullout Force* (Axial) Test Samples Crimped to Min/Max wire awg are subjected to an axial pullout force on the wire at a rate of 25 ± 6 mm (1 ± ¼ inch) per minute. The Test Samples must withstand Table 27* Force applied for 1 minute * See UL Standard 486A & B for Test Descriptions and Table information 6.0 PACKAGING Parts shall be packaged to protect against damage during handling, transit and storage. REVISION: C ECR/ECN INFORMATION: EC No: WNA2010-0414 DATE: 2011 / 08 / 01 DOCUMENT NUMBER: PS-19902-009 TITLE: PRODUCT SPECIFICATIONINSULKRIMP RING AND SPADE TERMINALS SHEET No. 3 of 3 CREATED / REVISED BY: CHECKED BY: APPROVED BY: E. THRODAHL J. MACNEIL J. MACNEIL TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC