0191600071

10 9 7 8 5 6 4 3 WIRE COMBINATIONS FOR NYLON-INSUALTED CLOSED END CONNECTORS NOTE: PRE-TWISTING NOT REQD FOR OEM APPLICATIONS SOLID: (OEM ONLY) A. STRIP LEADS TO .38(9.5) B. INSERT INTO CONNECTOR & CRIMP STRANDED: A. STRIP LEADS TO APROX. .75(19.1) B. TWIST WIRE COMBINATION EVENLY & TIGHT. C. TRIM STRIPPED PRE-TWISTED ZONE TO .38(9.5). D. INSERT INTO CONNECTOR AND CRIMP. MOLEX P/N: 191600009 (NC-2212), 191600129 (NC-2212BULK) 191600071 (NC-2212T), 191600109 (NC-2212BT) UL LISTED & CSA CERTIFIED WIRE COMBINATIONS SOLID OR STRANDED, COPPER WIRE ONLY ▽ E D ▽ C 14 AWG 16 AWG 18 AWG 20 AWG 22 AWG 1 1 1 1 1 2 1 1 1 1 1 2 1 1 1 1 1 2 1 1 3 1 1 1 2 1 3 1 1 3 2 2 1 2 2 2 1 2 2 2 1 2 2 2 3 2 1 1 2 1 1 2 1 1 1 1 2 1 1 1 2 1 3 1 1 1 2 1 3 4 1 1 1 1 1 2 1 3 4 1 5 1 ▽** * * - UL LISTED ONLY * - CSA CERTIFIED ONLY B 16 AWG 18 AWG 20 AWG 22 AWG 1 2 1 1 2 1 1 2 2 1 1 1 1 1 1 2 1 1 1 1 2 5 4 4 1 4 1 3 3 2 3 1 3 2 3 3 3 1 1 2 2 1 2 2 2 3 2 1 2 2 2 3 2 1 1 2 2 1 2 3 1 2 1 2 2 1 3 1 1 1 2 1 3 4 1 5 1 1 1 1 2 1 3 4 1 * * * * 1 WIRE PREPARATION F D1 2 14 AWG 16 AWG 18 AWG 20 AWG 22 AWG 1 1 2 1 1 3 4 1 1 1 2 2 1 2 3 1 3 2 6 5 5 1 4 4 1 4 2 3 3 1 3 2 3 3 2 2 1 2 2 2 3 4 2 1 1 1 2 1 3 4 1 5 1 6 5 4 3 1 2 1 3 4 1 1 1 1 1 F E .38 REF 9.7 RATING 105°C 600 VOLT (1000 VOLT IN SIGNS OR FIXTURES) FILE: E32244 RATING 105°C 600 VOLT (1000 VOLT IN SIGNS OR FIXTURES) FILE: LR 18689 * 125°C FOR PRE-TWISTED WIRE ONLY D APPLICATION WITH HANDTOOL: HOLD TOOL WITH LOCATOR PLATE FACING UP. INSERT CLOSED END CONNECTOR IN HOLE. INSURE THAT SHOULDER OF CONNECTOR IS RESTING ON LOCATOR PLATE. CLOSE TOOL JAWS UNTIL CONNECTOR IS HELD SNUG IN PLACE. LOAD CONNECTOR WITH DESIRED WIRE COMBINATION. COMPLETE CRIMP BY CLOSING TOOL HANDLES UNTIL THEY RELEASE. C CRIMP TOOLING AVAILABLE 192280030 (ATP-301) AIR TAPE PRESS OR 638853500 MINI-MAC TAPE APPLICATOR WITH 192880239 (ATP-NC-2212) CRIMPING DIES D1 ▽- STRANDED WIRE ONLY 640010900 (RHT-7050) HANDTOOL 640050900 (AT-7050) CRIMP HEAD OR 640053600 (AT-2212) CRIMP HEAD FOR 192790001 (AT-200) AIR HAND TOOL B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: WIRE COMBO: (1) 14 AWG + NOTE: THIS DOCUMENT USED TO MAKE STUFFER SHEET PART NO: 194080109 DOC NO'S: E-19160-009 & PK-19408-109 = 0 INCH/MM = 0 GENERAL TOLERANCES (UNLESS SPECIFIED) MM = 0 ± 3 PLACES ± ± ± 0 PLACES ± ± ANGULAR TOL FORMAT: Eng-lega-master-tb-prod-B REVISION: E1 DATE: 2021/05/01 10 P1 RELEASE DATE 9 2022/05/04 ± ± 1 PLACE DOCUMENT STATUS INCH 4 PLACES ± DIVISIONAL SYMBOLS 2 PLACES ± A ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:37:30 8 7 6 5 (1) 16 AWG "STRANDED" ONLY WAS "STRANDED OR SOLID". CRIMP TOOLING PN'S UPDATED. NTS 4 ° EC NO: 704038 DRWN: DMYRICK CHK'D: JMACNEIL APPR: JMACNEIL INITIAL REVISION: DRWN: APPR: THIRD ANGLE PROJECTION 3 2022/04/07 2022/05/04 2022/05/04 CLOSED END CONNECTOR WIRE COMBINATNS NC-2212 PRODUCT SPECIFICATION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER PS-19160-006 DRAWING SERIES B-SIZE 19160 MATERIAL NUMBER 191600009 2 PSD 001 CUSTOMER GENERAL MARKET D1 SHEET NUMBER 1 OF 1 1 A