0191600169

10 F 9 7 8 6 5 4 3 2 1 F WIRE COMBINATIONS FOR NYLON-INSUALTED CLOSED END CONNECTORS F MOLEX P/N: 191600002 (NC-1610), 191600128 (NC-1610 BULK) 191600083 (NC-1610T), 191600156 (NC-1610BT) NOTE: PRE-TWISTING NOT REQD FOR OEM APPLICATIONS SOLID: (OEM ONLY) A. STRIP LEADS TO .38(9.5) B. INSERT INTO CONNECTOR & CRIMP STRANDED: A. STRIP LEADS TO APROX. .75(19.1) B. TWIST WIRE COMBINATION EVENLY & TIGHT. C. TRIM STRIPPED PRE-TWISTED ZONE TO .38(9.5). D. INSERT INTO CONNECTOR AND CRIMP. UL LISTED & CSA CERTIFIED WIRE COMBINATIONS SOLID OR STRANDED, COPPER WIRE ONLY E 12 AWG 14 AWG 16 AWG 18 AWG 1 1 1 1 1 2 1 1 1 2 1 1 1 2 1 3 1 1 1 1 1 1 2 1 3 4 1 2 1 2 2 2 3 D 12 AWG 14 AWG 16 AWG 18 AWG 2 3 1 3 3 5 1 4 2 6 1 2 1 1 3 1 1 5 2 1 .38 REF 9.7 192880030 (ATP-301) AIR TAPE PRESS OR 638858400 MINI-MAC TAPE APPLICATOR WITH 192880236 (ATP-NC-1610) CRIMPING DIES OR NCEC CRIMP DIE-MARKED, "SIZE 16-10" F E D 640010600 (RHT-7000) HANDTOOL 640050600 (AT-7000) CRIMP HEAD OR 640053500 (AT-1610) CRIMP HEAD FOR 192790001 (AT-200) AIR HAND TOOL RATING 105°C 600 VOLT (1000 VOLT IN SIGNS OR FIXTURES) FILE: LR 18689 * 125°C FOR PRE-TWISTED WIRE ONLY (1) 18 AWG SOLID WITH (2) 18 AWG STRANDED (2) 18 AWG SOLID TWISTED OR UNTWISTED (2) 18 AWG STRANDED TWISTED OR UNTWISTED (1) 12 AWG SOLID WITH (1) 14 AWG STRANDED (1) 12 AWG SOLID WITH (1) 12 AWG STRANDED (1) 20 AWG STRANDED WITH (1) 18 AWG STRANDED (1) 20 AWG STRANDED WITH (2) 18 AWG STRANDED (2) 20 AWG STRANDED WITH (1) 18 AWG STRANDED (3) 20 AWG STRANDED (3) 20 AWG STRANDED WITH (1) 18 AWG STRANDED (4) 20 AWG STRANDED (1) 20 AWG STRANDED WITH (2) 14 AWG STRANDED (2) 12 AWG STRANDED (3) 14 AWG STRANDED (3) 14 AWG SOLID HOLD TOOL WITH LOCATOR PLATE FACING UP. INSERT CLOSED END CONNECTOR IN HOLE. INSURE THAT SHOULDER OF CONNECTOR IS RESTING ON LOCATOR PLATE. CLOSE TOOL JAWS UNTIL CONNECTOR IS HELD SNUG IN PLACE. LOAD CONNECTOR WITH DESIRED WIRE COMBINATION. COMPLETE CRIMP BY CLOSING TOOL HANDLES UNTIL THEY RELEASE. CRIMP TOOLING AVAILABLE: RATING 105°C 600 VOLT (1000 VOLT IN SIGNS OR FIXTURES) FILE: E32244 ADDITIONAL UL LISTED WIRE COMBINATIONS C APPLICATION WITH HANDTOOL: WIRE PREPARATION: F C B B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: P/N TYPO/ ERROR: 191600128 NOTE: THIS DOCUMENT USED TO MAKE STUFFER SHEET PART NO: 194080109 DOC NO'S: E-19160-009 & PK-19408-109 = 0 INCH/MM = 0 GENERAL TOLERANCES (UNLESS SPECIFIED) MM = 0 ± 3 PLACES ± ± FORMAT: Eng-lega-master-tb-prod-B REVISION: E1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/05/04 ± ± ± 0 PLACES ± ± 1 PLACE ANGULAR TOL DOCUMENT STATUS INCH 4 PLACES ± DIVISIONAL SYMBOLS 2 PLACES ± A ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:37:29 8 7 6 5 WAS 191620128 & 191600156 WAS 191620156. CRIMP TOOLING PN'S UPDATED. NTS 4 ° EC NO: 704038 DRWN: DMYRICK CHK'D: JMACNEIL APPR: JMACNEIL INITIAL REVISION: DRWN: JHACKNEY APPR: JMACNEIL THIRD ANGLE PROJECTION 3 2022/04/08 2022/05/04 2022/05/04 CLOSED END CONNECTOR WIRE COMBINATNS NC-1610 PRODUCT SPECIFICATION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1999/11/01 2012/06/06 DRAWING SERIES B-SIZE 19160 PS-19160-005 MATERIAL NUMBER SEE CHART 2 PSD 001 CUSTOMER GENERAL MARKET F SHEET NUMBER 1 OF 1 1 A