0191600171

10 9 7 8 6 5 4 3 F 2 1 F WIRE PREPARATION NOTE: PRE-TWISTING NOT REQD FOR OEM APPLICATIONS SOLID: (OEM ONLY) A. STRIP LEADS TO .38(9.5) B. INSERT INTO CONNECTOR & CRIMP STRANDED: A. STRIP LEADS TO APROX. .75(19.1) B. TWIST WIRE COMBINATION EVENLY & TIGHT. C. TRIM STRIPPED PRE-TWISTED ZONE TO .38(9.5). D. INSERT INTO CONNECTOR AND CRIMP. WIRE COMBINATIONS FOR NYLON-INSUALTED CLOSED END CONNECTORS D1 MOLEX P/N: 191600012 (NC-2214), 191600130 (NC-2214BULK) 191600070 (NC-2214T), 191600091 (NC-2214BT) D1 D1 E UL LISTED WIRE COMBINATIONS D C .38 REF 9.7 STRANDED WIRE ONLY STRANDED WIRE ONLY 16 AWG 18 AWG 20 AWG 22 AWG 7 1 6 5 1 4 2 4 1 2 3 1 3 3 2 1 2 4 1 2 1 1 1 4 1 3 1 2 2 1 1 1 3 16 AWG 18 AWG 20 AWG 22 AWG 2 1 1 1 1 1 1 2 2 2 1 3 1 1 1 1 1 1 2 1 1 1 2 1 1 3 3 1 2 2 4 1 5 1 6 1 1 1 1 RATING 105°C 300 VOLT FILE: E32244 D RATING 125°C 300 VOLT FILE: LR 18689 APPLICATION WITH HANDTOOL: HOLD TOOL WITH LOCATOR PLATE FACING UP. INSERT CLOSED END CONNECTOR IN HOLE. INSURE THAT SHOULDER OF CONNECTOR IS RESTING ON LOCATOR PLATE. CLOSE TOOL JAWS UNTIL CONNECTOR IS HELD SNUG IN PLACE. LOAD CONNECTOR WITH DESIRED WIRE COMBINATION. COMPLETE CRIMP BY CLOSING TOOL HANDLES UNTIL THEY RELEASE. CSA CERTIFIED WIRE COMBINATIONS ADDITIONAL UL LISTED WIRE COMBINATIONS (7) 22 AWG STRANDED (4) 22 AWG STRANDED WITH (2) 20 AWG STRANDED (2) 20 AWG STRANDED WITH (1) 16 AWG STRANDED (2) 18 AWG STRANDED WITH (1) 20 AWG STRANDED (3) 18 AWG STRANDED (2) 18 AWG SOLID (3) 18 AWG SOLID (2) 18 AWG SOLID E C CRIMP TOOLING AVAILABLE D1 640010600 (RHT-7000) HANDTOOL 640053400 (AT-2214) CRIMP HEAD OR 640050600 (AT-7000) CRIMP HEAD FOR 192790001 (AT-200) AIR HAND TOOL 192280030 (ATP-301) AIR TAPE PRESS OR 638853500 MINI-MAC TAPE APPLICATOR WITH 192880242 (ATP-NC-2214) CRIMPING DIES B B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: P/N TYPO/ ERROR: 191600070 NOTE: THIS DOCUMENT USED TO MAKE STUFFER SHEET PART NO: 194080109 DOC NO'S: E-19160-009 & PK-19408-109 = 0 INCH/MM = 0 NTS GENERAL TOLERANCES (UNLESS SPECIFIED) MM = 0 ± 3 PLACES ± ± ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-B REVISION: E1 DATE: 2021/05/01 10 P1 RELEASE DATE 9 2022/05/04 ± ± 1 PLACE A INCH 4 PLACES ± DIVISIONAL SYMBOLS 2 PLACES ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:37:31 8 7 6 5 4 WAS 191600071, 191600130 WAS 190600129, 191600091 WAS 191600190. CRIMP TOOLING PN'S UPDATED. ° EC NO: 704038 DRWN: DMYRICK CHK'D: JMACNEIL APPR: JMACNEIL INITIAL REVISION: DRWN: JHACKNEY APPR: JMACNEIL THIRD ANGLE PROJECTION 3 2022/04/07 2022/05/04 2022/05/04 CLOSED END CONNECTOR WIRE COMBINATNS NC-2214 PRODUCT SPECIFICATION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1999/11/03 2012/06/06 DRAWING SERIES B-SIZE 19160 PS-19160-007 MATERIAL NUMBER SEE CHART 2 PSD 001 CUSTOMER GENERAL MARKET D1 SHEET NUMBER 1 OF 1 1 A