0191600172

10 9 8 7 5 6 4 3 WIRE COMBINATIONS FOR NYLON-INSUALTED CLOSED END CONNECTORS F 2 WIRE PREPARATION A.) STRIP LEADS TO APPROXIMATELY .88 (22.2) B.) PRETWIST WIRE COMBINATION EVENLY AND TIGHT. C.) TRIM STRIPPED PRETWISTED ZONE TO .50 (12.7) LONG. MOLEX P/N: 191600024 (NC-8), 191600131 (NC-8 BULK) 191600028 (NC-8T) 8 AWG E D C 1 1 1 1 B 10 AWG 12 AWG 14 AWG 16 AWG 18 AWG 5 3 5 2 5 1 4 4 6 4 5 4 4 4 3 4 2 4 1 3 8 7 3 3 6 5 3 4 3 3 3 3 2 2 9 8 7 6 5 4 11 10 9 8 7 6 5 12 11 10 9 8 7 1 1 1 2 STRANDED WIRE ONLY STRANDED WIRE ONLY 10 AWG 12 AWG 14 AWG 16 AWG 18 AWG 2 1 1 1 2 4 1 1 2 1 1 1 6 5 1 4 1 1 3 1 2 1 1 1 3 1 2 1 1 5 1 4 1 1 3 1 2 1 8 7 1 1 6 5 1 4 1 1 3 2 2 2 3 2 2 2 1 4 2 2 3 2 2 2 1 2 3 6 5 4 4 2 4 1 12 AWG 14 AWG 16 AWG 18 AWG 3 3 3 3 2 3 1 5 3 4 3 3 3 3 2 3 1 4 2 2 3 2 2 2 1 7 2 2 6 5 2 4 2 2 3 2 2 1 6 5 1 4 1 1 3 1 10 1 9 1 8 7 1 1 6 5 1 4 1 7 7 1 6 6 3 6 2 6 1 5 5 4 4 1 * E RATING 105°C 600 VOLT (1000 VOLT IN SIGNS OR FIXTURES) FILE: E32244 RATING 125°C 600 VOLT (1000 VOLT IN SIGNS OR FIXTURES) FILE: LR 18689 D APPLICATION WITH HANDTOOL: HOLD TOOL WITH LOCATOR PLATE FACING UP. INSERT CLOSED END CONNECTOR IN HOLE. INSURE THAT SHOULDER OF CONNECTOR IS RESTING ON LOCATOR PLATE. CLOSE TOOL JAWS UNTIL CONNECTOR IS HELD SNUG IN PLACE. LOAD CONNECTOR WITH DESIRED WIRE COMBINATION. COMPLETE CRIMP BY CLOSING TOOL HANDLES UNTIL THEY RELEASE. C CRIMP TOOLING AVAILABLE D1 ALTERNATE: HOLLINGSWORTH HAND TOOL USING: H-15 OR H38-15 DIE NUMBERS. * - RATED 300 VOLTS ALL OTHER 600 VOLTS (2) 12 AWG STRANDED WITH (1) 12 AWG SOLID NOTE: THIS DOCUMENT USED TO MAKE STUFFER SHEET PART NO: 194080109 DOC NO'S: E-19160-009 & PK-19408-109 = 0 INCH/MM = 0 = 0 FORMAT: Eng-lega-master-tb-prod-B REVISION: E1 DATE: 2021/05/01 10 RELEASE DATE 9 2022/05/04 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 3 PLACES ± ± ± ± ± 0 PLACES ± ± 1 PLACE ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 8 7 6 5 4 CLOSED END CONNECTOR WIRE CONBINATIONS NC-8 PRODUCT SPECIFICATION INCH 4 PLACES ± DIVISIONAL SYMBOLS 2 PLACES ± 14:37:32 UPDATED. NTS ANGULAR TOL P1 B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: CRIMP TOOLING PN'S MM DOCUMENT STATUS 640012500 (RHT-2080) HANDTOOL 640052500 (AT-2080) CRIMP HEAD FOR 192790001 (AT-200) AIR HAND TOOL 192280030 (ATP-301) AIR TAPE PRESS OR 638853500 MINI-MAC TAPE APPLICATOR WITH 192880245 (ATP-NC-8) CRIMPING DIES ADDITIONAL UL/ CSA WIRE COMBINATIONS A F .50 REF 12.7 UL LISTED & CSA CERTIFIED WIRE COMBINATIONS STRANDED WIRE ONLY 1 ° EC NO: 704038 DRWN: DMYRICK CHK'D: JMACNEIL APPR: JMACNEIL INITIAL REVISION: DRWN: JHACKNEY APPR: JMACNEIL THIRD ANGLE PROJECTION 3 2022/04/11 2022/05/04 2022/05/04 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1999/11/03 2012/06/06 DRAWING SERIES B-SIZE 19160 PS-19160-008 MATERIAL NUMBER SEE CHART 2 PSD 001 CUSTOMER GENERAL MARKET D1 SHEET NUMBER 1 OF 1 1 A