02061131

12 11 9 7 8 5 6 4 3 2 1 ENG. NO. PACKAGING PART NO. H 10 1855-(P901) 1855-(P901)L 1855-(P561) 1855-(P561)L 1855-(P550) 1855-(P550)L 1855-(P228) 1855-(P228)L 1855-1(P901) 1855-1(P901)L 1855-(P901)1 02-06-1131 02-06-1132 02-06-5138 02-06-5139 02-06-5130 02-06-5135 02-06-5147 02-06-5148 02-06-1141 NOT TOOLED 02-06-1143 18550000-PK PK-1190-003 18550000-PK (2.03) (1.90) H .080 .075 PK-1190-003 18550000-PK PK-1190-003 18550000-PK PK-1190-003 (3.20) .126 (25.40) (1.90/1.73) 1.000 18550000-PK PK-1190-003 PK-18550001-PK (1.90) .075/.068 .075 CARRIER VIEW ACTUAL SIZE G SECT. "B-B" SECT. "C-C" SCALE:10X SCALE:10X G GAP ACCEPTABLE SEE ALTERNATE (.25) MAX. .010 CARRIER CUTOFF LEGEND F TIP VIEW F E SELECT GOLD PLATE DEPTH (WHEN SPECIFIED) SELECT GOLD FLASH PLATE DEPTH (WHEN SPECIFIED) (16.8) FORM BLANK=CHAIN 1=CHAIN WITH INTERLEAF PAPER ON REEL. L=LOOSE P=PREPLATE BLANK=POSTPLATE DIA. .059/.056 1855-✴(✴✴✴✴)✴ BLANK=WITH LOCKING TABS 1=WITHOUT LOCKING TABS (1.50/1.42) "A" .66 SEE NOTE 7 E FINISH CODE D C OPTIONAL LOCKING TAB (2 PL.) SEE LEGEND NOTES: 1. MATERIAL: BRASS 2. FINISHES: 901 HOT TIN DIP (.00051)/.000020 MIN. 228 SELECT GOLD PLATE (.00075/.000030 MIN. IN CONTACT AREA, SELECT TIN (.00250)/.000100 MIN. IN CRIMP AREA OVER (.00125)/.000050 MIN. NICKEL OVERALL 561 SELECT GOLD PLATE (.00076)/.000030 MIN. IN CONTACT AREA, (.00127)/.000050 MIN. NICKEL OVERALL. 550 SELECT GOLD PLATE (.00038)/.000015 MIN. IN CONTACT AREA, OVER (.00076)/.000030 MIN. NICKEL OVERALL WITH (.00025)/.000010 MAX. GOLD FLASH OVERALL. 3. PRODUCT SPECIFICATION: PS-02-06 4. PACKAGE INFORMATION: SEE CHART 5. TERMINAL FOR USE WITH (1.57)/.062 DIA. SERIES HOUSINGS AND WILL ACCEPT 24 THRU 30 AWG WIRE WITH (1.02/2.29)/.040/.090 INSULATION DIAMETER. 6. PARTS CONFORM TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 7. MARKING MAY VARY ON PARTS, CONSULT FACTORY. 8. TIP GEOMETRY IS TOOL DEPENDENT. EITHER GEOMETRY IS ACCEPTABLE. "B" "B" (2.03) D .080 "C" (.25) MAX. .010 CARRIER CUTOFF "C" "A" (1.93) C .076 SECT. "A-A" ALTERNATE TIP GEOMETRY SEE NOTE 8 B SYMBOLS = 0 = 0 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN NTS = 0 A MM ± 3 PLACES ± ± DOCUMENT STATUS 12 P1 RELEASE DATE 11 2019/05/10 10 19:11:22 C 0.25 ± 0.014 ± 0.35 ± 1 PLACE = 0 0 PLACES ± 9 8 7 6 = 0 0.01 2 PLACES ± ANGULAR TOL FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 INCH 4 PLACES ± = 0 = 0 CURRENT REV DESC: ADD CHAIN PK SPEC GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 = 0 B ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 614240 DRWN: JEHRISMAN CHK'D: FSMITH APPR: FSMITH INITIAL REVISION: DRWN: GEP APPR: RAS THIRD ANGLE PROJECTION 4 2019/03/22 2019/05/10 2019/05/10 CRIMP TERMINAL, FEMALE (1.57)/.062 DIA., BRASS FOR 24 THRU 30 GA. WIRE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1987/09/17 1987/09/17 DRAWING SERIES C-SIZE 1855 3 SD-1855-X MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 AP3 SHEET NUMBER 1 OF 1 1 A