0334762071

IF HEADER IS RECESSED INTO POCKET. THESE DIMENSIONS REPRESENT THE MINIMUM CLEARANCE REQUIRED FOR THE MATING SHROUD. 26.3 MIN A B B 32.5° 50° 26.3 MIN B20 1.8 ±0.2 32.5° 5° B21 BACK ANGLE R2.00 50° 7.41 7.41 12.23 A MIN 16.7 MIN A 30° 12.23 B 20.5 MIN ALL AROUND FOR MATING CONNECTOR SHROUD CLEARANCE B1 D B +0.10 21.09 -0.20 24.12 KEYING OPTION A +0.10 -0.20 24.12 SCALE 2:1 B14 �2.92� 21.09 +0.10 -0.20 +0.10 -0.20 SCALE 1:1 D 0.70 ±0.15 ALL AROUND SEE SECTION A-A B22 FOR DETAILS R�6.47� KEYING OPTION E SCALE 2:1 B14 B B PACKAGING FRAME DETAIL F SCALE 10:1 Connector Description D B D D B 15° 2X 17.00 MIN 15° 50° 32.5° 1.05 ±0.05 ⌖ 0.2Ⓜ A B 15.92 15.92 B6 3.00 ⌖ 0.20 A B +0.10 -0.20 16.76 B 24.12 ⌖ 0.50 A B +0.10 -0.20 21.09 B DETAIL C SCALE 10:1 APPLIES 2X SEE KEYING OPTION VIEWS FOR POSITIONS +0.10 -0.20 KEYING OPTION F SCALE 2:1 B14 KEYING OPTION B SCALE 2:1 B14 C CONNECTOR WITH CLIP-SLOT 16.7 B2 B8 A B +0.10 -0.20 12.7 A 2.30 B7 16.76 CONNECTOR WITHOUT CLIP-SLOT 8.43 12.23 7.41 DIMENSION A 12X �1.20� SEE NOTE 8 (150-T001) ⌖ 0.30Ⓜ A B 2X 8.75 CIRCUIT #2 C CIRCUIT #7 10X 3.50 CIRCUIT #8 SEE DETAIL C CIRCUIT #1 2X 3.75 B B 15° 50° 7.41 6X 3.25 B15 18.00 15° 32.5° G 15.92 A D 15.92 B16 B +0.10 16.76 -0.20 16.76 B23 KEYING OPTION C SCALE 2:1 B14 +0.10 -0.20 12.10 KEYING OPTION G SCALE 2:1 B14 ⌖ 0.20Ⓜ A B AT BASE ⌖ 0.30Ⓜ A B AT TIP +0.15 -0.10 7.41 15.92 15.92 1.50 ALL AROUND 32.5° 50° 12.23 B B +0.10 16.76 -0.20 16.76 4X �2.50� SEE NOTE 8 (280-T001) 2X 33.00 SURFACE MUST BE FREE OF DEFECTS AND PARTING LINES FOR SEALING SURFACE ALL AROUND +0.10 12X 9.30 -0.25 +0.10 -0.20 21.09 KEYING OPTION D SCALE 2:1 B14 ⌢ 0.15 A +0.10 -0.20 +0.10 -0.20 1.20 ±0.05 TYP. ⌖ 0.10Ⓜ A B KEYING OPTION H SCALE 2:1 B14 ⌖ 0.20Ⓜ A B AT BASE ⌖ 0.30Ⓜ A B AT TIP B10 B +0.10 -0.20 B11 MEASURED AT 2.9 FROM -AALL AROUND 999-S-016-2-G01 G YELLOW 999-S-016-2-F01 F YELLOW 999-S-016-2-E01 E YELLOW 999-S-016-2-D01 D BLACK 999-S-016-2-C01 C DARK GREY 2.10 ±0.05 TYP. ⌖ 0.10Ⓜ A B DETAIL E SCALE 10:1 B3 AT -G- 4X 3.50 0.40 ±0.05 TYP. ⌖ 0.10Ⓜ A B 20.00 ⌖ 0.10Ⓜ A B 1. DRAFT ANGLE PERMISSIBLE 0.25° MAXIMUM. 2X R846.45 8.40 ±0.05 2. ALL DIMENSIONS SHOWN IN MILLIMETERS. 3. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 999-S-016-2-B01 B GREY 999-S-016-2-A01 EWCAP PIN A OPTION 6. A FULL SHROUD ON THE MATING CONNECTOR IS REQUIRED TO INSURE THAT THE CONNECTOR-HEADER POLARIZATION FEATURES (OPTIONS A THRU H) WILL FUNCTION. THE SHROUD ALSO PREVENTS SCOOP DAMAGE TO THE HEADER PINS. REFER TO "SAE/USCAR-12 CONNECTOR DESIGN GUIDE LINES" FOR ADDITIONAL INFORMATION. 18.40 B17 BLACK MATING CONNECTOR COLOR 4 B23 AT DATUM -D- B13 B12 B5 B19 ADDED 4X (0.805) ⌖ 0.20Ⓜ A B AT BASE 1-14-11 3-11-11 1-14-11 B18 CHANGED 16X TO 12X FOR THE 1.5 B17 UPDATED CONNECTOR COLORS 1-14-11 088 B16 ADDED -G- 5-04-10 088 B15 REMOVED ∥ 0.10Ⓜ A B 5-04-10 088 B14 REMOVED SHORTING BAR NOTE 5-04-10 088 B13 UPDATED NOTE 8 REMOVED REV F 5-04-10 088 B12 ADDED NOTE 9 5-04-10 088 B11 ADDED DIM 1.35+0.10/-0.20 MEASURED 5-04-10 B 088 B10 ADDED SEE NOTE 8 5-04-10 088 B9 2.50 WAS 2.80, ADDED (280-T001) 5-04-10 088 B8 ADDED ⌖ 0.50 A B 5-04-10 088 B7 ADDED ⌖ 0.20 A B 5-04-10 088 B6 ADDED DIM 8.43 5-04-10 088 B5 ADDED SEC C-C 5-04-10 088 B4 UPDATED SEC B-B 5-04-10 088 B3 ADDED DETAIL D 5-04-10 088 B2 ADDED SEC C-C 5-04-10 088 B1 ADDED DIM 0.70±0.15 ALL AROUND 5-04-10 088 B 5-04-10 KC RELEASED 0.69 ±0.05 TYP. ⌖ 0.10Ⓜ A B .X THIRD ANGLE PROJECTION MILLIMETERS A ±3° ANGLES CONSTRUCTION BELOW THIS SURFACE IS NOT CONTROLED BY EWCAP. NO PLASTIC FEATURES MAY EXTEND ABOVE THIS SURFACE MV DATE DWN CHK REVISION RECORD DIMENSIONS ARE IN ±0.2 .XX ±0.10 AT -GDRAWN BY SCALE 20.50 ⌖ 0.10Ⓜ A B 8. FOR BLADE TERMINAL DESIGN INFORMATION SEE EWCAP DWG. # EWCAP-001 4 - 1 SECTION B-B SCALE 3:1 SCALE 3:1 2 DATE CHECKED BY G.ELLIOTT M.VANSLAMBROUCK 08-03-20 TITLE DIRECT CONNECT INTERFACE 16 WAY (2 X 8) 1.5MM SEALED MALE AT -G- 9. THIS IS A 100% CAD GENERATED PART. THE CAD MATHEMATICAL DATA IS THE MASTER FOR THIS PART. FOR DIMENSIONAL OR ANY INFORMATION NOT SHOWN ON THIS DRAWING, ANALYZE THE CAD MODEL. 3 088 TOLERANCES (UNLESS OTHERWISE SPECIFIED) 7. REFER TO USCAR/EWCAP PART LIST AS FOUND ON WEBSITE http://www.uscarteams.org SECTION D-D 088 CHANGE SERIAL LET NUMBER 14.00 G 5. STANDARD COLORS FOR POLARIZATION (SEE CHART). DEVATION REQUIRES APPROVAL OF AUTHORIZED PERSON. 43.70 B20 CHANGED FROM 1.79 TO 1.80 AT 2.9 FROM -A- ALL AROUND NOTES: UNLESS OTHERWISE SPECIFED 2X R53.82 YELLOW 088 BLADE TERMINALS 1.35 4X 7.00 4X R3.65 H 3-11-11 B21 REMOVED THE WORD "OPTION" AND ⌖ 0.30Ⓜ A B AT TIP FOR 2.8 0.75 ±0.05 ⌖ 0.10Ⓜ A B 4. RADII ON ALL CORNERS SHOWN SHARP OR ALL UNSPECIFED RADII: 0.25 EXCEPT AS NOTED. 999-S-016-2-H01 3-11-11 B9 1.85 ±0.05 ⌖ 0.10Ⓜ A B 0.75 TYP. AT -G- SECTION A-A B A B22 ADDED REF DIMENSION FOR 088 +0.10 4X 8.55 -0.25 24.12 ⌖ 0.30Ⓜ A B B19 B18 12X �0.805� SEE NOTE 8 (150-T001) B 15° 088 BLADE TERMINALS B 15° 3-25-11 MV GE AT VIEW OF BACK ANGLE CIRCUIT #15 2X 16.50 SEE DETAIL E B B23 ADDED DRAFT DIRECTION SYMBOL CIRCUIT #16 CIRCUIT #10 4X �0.805� SEE NOTE 8 (280-T001) B 088 088 A 8-3-20 LATCH HEIGHT CIRCUIT #9 SEE DETAIL F +0.10 21.09 -0.20 24.12 6X 6.50 CHARTED DIMENSION ADDED FOR WITH AND WITHOUT CLIPSLOT C B 12.90 +0.20 2.90 -0.80 AT TANGENT +0.10 -0.20 162 2X 7.50 8.43 B 12.23 B B B4 1 OF 1 REVISION LEVEL SIZE DRAWING NUMBER SHEET 999-S-016-2-Z02 1 E DO NOT SCALE DRAWING COMPUTER AIDED DRAWING C