0334810602

18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 TABLE OF CONTENTS L 2 1 MATING CONNECTOR DRAWINGS SHEET NO. SHEET DESCRIPTION 1 NOTES AND BOM 2 CONFIGURATIONS 3-4 KEY CONFIGURATIONS 5 BLADE SEALED ASSEMBLY 6 SYSTEM PACKAGING 7 BACKSHELL NOTES 8 BACKSHELL 9 BACKSHELL CONFIGURATIONS NOTES: VALID UNLESS OTHERWISE SPECIFIED DESCRIPTION 1X2 MOLEX INLINE SD-33471-0001 1X6 SD-33471-0001 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-33472-100 -CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY CHECKING, CRIMPING, AND TROUBLESHOOTING. -DESIGNED TO MATE WITH RECEPTACLE SEALED ASSEMBLY AS SPECIFIED IN THE MATING CONNECTOR DRAWINGS CHART. *DENOTES DRAWINGS THAT CAN BE ACCESSED AT http://ewcap.uscarteams.org/ -ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION (SEE PLR PRE-LOCK VIEW SHEET 5). K L K J b. PRODUCT SPECIFICATION SEE: -STANDARD CONFIGURATION: PS-33471-000 -UL V0 CONFIGURATION: PS-160105-0001 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY), TERMINALS, WIRE DIAMETER RANGE, PRODUCT VALIDATION, AND PRODUCT DEVIATIONS. c. PACKAGING SPECIFICATION PER MOLEX DRAWING: PK-31300-635 (PK-33471-000 FOR 1X5) d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR PRODUCTS AND PACKAGING SPECIFICATION: QEHS-699000-300 e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) J H 2. DESIGN - MATERIALS: a. FOR BILL OF MATERIALS SEE: -STANDARD CONFIGURATION: SD-33481-0002 -UL V0 CONFIGURATION: SD-160106-0002 H 3. DESIGN - GEOMETRY: a. THE 3-D CAD DATA IS BASIC (WITHOUT TOLERANCE) AND MASTER FOR THIS PART WITH THE EXCEPTION OF UNDERLINED DIMENSIONS. DIMENSIONAL INFORMATION NOT SHOWN ON THIS DRAWING IS DEFINED BY THE DATA FILE AT ITS LATEST REVISION. b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M-2009 c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715 d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX. e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD. THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION, AND CUSTOMER MATERIAL NUMBER. f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B). g. LASER MARKING: 1. PART NUMBER 2. DAY OF THE YEAR 3. SHIFT 4. YEAR FOR ADDITIONAL INFORMATION SEE SECTION 5 UNDER PROCEDURES IN ES-34735-008. 1X2 G F G F E E D D C A1 NX REMASTERING，CHANGE PS DRAWING NUMBER FROM PS-160105-0001 TO PS-160074-0001 IN NOTES 1.b A 2 MINOR GEOMETRY CHANGE FOR UL V0 UPDATED VIEWSETS 1 INITIAL RELEASE REV REV DESCRIPTION INSPECTION NUMBER LOG LAST NUMBER: 9 ADDED: REMOVED: SYMBOLS B = 0 = 0 = 0 A DOCUMENT STATUS FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 P1 17 RELEASE DATE 16 2018/10/04 15:02:02 15 14 13 12 11 10 9 8 7 MM ONLY 1.5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C SCALE ± = 0 1X6 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL = 0 C 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 1 OF 9 1 A 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 SHEET DESCRIPTION CONFIGURATIONS L L K K UL V0 UNIQUE FEATURE Partial1 SCALE 10:1 J J H H 1X2 - UL V0* 1x2 - STD G G F F E E D D * MINOR GEOMETRY DIFFERENCE THAN STANDARD CONFIGURATION. SEE NOTES 1 & 2 FOR MORE INFORMATION C SYMBOLS B = 0 = 0 = 0 A 1x6 - UL V0* 1x6 - STD DOCUMENT STATUS FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 P1 RELEASE DATE 17 16 2018/10/04 15 14 13 12 11 10 9 8 7 MM ONLY 1.5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C SCALE ± = 0 15:02:02 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL = 0 C 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 2 OF 9 1 A 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 SHEET DESCRIPTION KEY CONFIGURATIONS 1X2 L L 60° 60° K K KEY A J J 35° 60° H H KEY B G G 35° 60° F F E E KEY C 35° 35° D D C C KEY D SYMBOLS B = 0 = 0 = 0 A FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 RELEASE DATE 17 16 2018/10/04 15:02:02 15 14 13 12 11 10 9 8 7 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C MM ONLY 3:1 ± = 0 P1 SCALE ANGULAR TOL = 0 DOCUMENT STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 3 OF 9 1 A 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 SHEET DESCRIPTION KEY CONFIGURATIONS CONT. L L 1X6 60° 60° K K J J KEY A 30° 60° H H G G KEY B 30° 60° F F E E KEY C 30° 30° D D C C KEY D SYMBOLS B = 0 = 0 = 0 A FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 RELEASE DATE 17 16 2018/10/04 15:02:02 15 14 13 12 11 10 9 8 7 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C MM ONLY 3:1 ± = 0 P1 SCALE ANGULAR TOL = 0 DOCUMENT STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 4 OF 9 1 A 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 SHEET DESCRIPTION 1 CHARTED DIMENSIONS BLADE SEALED ASSEMBLY DESCRIPTION L 1X2 A N/A 1X6 29.69 DIMENSIONS B D C 1.75 21.00 55.50 E 17.30 54.45 17.23 1.75 31.71 9 ⌀DIM C K K MIN PASS-THRU WITH NO CLEARANCE OPTIONAL LASER MARKING ON THIS SURFACE SEE NOTE 3g. TERMINAL POSITION 1 2X DIM B J 3.50 TYP. L J Z B DIM E MAX 3 H A A B H Z LAST TERMINAL POSITION DIM A MAX 2 REAR VIEW (WIRE HARNESS SIDE) DIM D MAX 4 G G F F 6 11.00 5 2.00 E E 7 6.60 D 8 15.00 D PARTIAL A-A SCALE 3:1 C C SYMBOLS B = 0 = 0 = 0 PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN FINAL-LOCK POSITION PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN PRE-STAGED POSITION SECTION B-B A SECTION Z-Z FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 P1 RELEASE DATE 17 16 2018/10/04 15 14 13 12 11 10 9 8 7 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C MM ONLY 3:1 ± = 0 15:02:02 SCALE ANGULAR TOL = 0 DOCUMENT STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 5 OF 9 1 A 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 SHEET DESCRIPTION BACKSHELL L L K K J J H H Y Y G G F F E E 11.00 1.50 D 6.40 D 10.80 PARTIAL Y-Y SCALE 3.5:1 C C SYMBOLS B = 0 = 0 = 0 A FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 RELEASE DATE 17 16 2018/10/04 15:02:02 15 14 13 12 11 10 9 8 7 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C MM ONLY 3.5:1 ± = 0 P1 SCALE ANGULAR TOL = 0 DOCUMENT STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 8 OF 9 1 A 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 SHEET DESCRIPTION 2 1 CHARTED DIMENSIONS BACKSHELL CONFIGURATIONS CKT L BLADE RECEPTACLE CONFIGURATION CONFIGURATION 1X2 �137.46� STANDARD STANDARD DIMENSIONS M N P R 107.84 29.50 27.00 26.25 S 25.00 L ⌀DIM N MIN PASS-THRU WITH NO CLEARANCE K K J J OVERALL MATED SYSTEM WITH BLADE AND RECEPTACLE BACKSHELL �103.47� ⌀DIM P MIN PASS-THRU WITH NO CLEARANCE H H G G OVERALL MATED SYSTEM WITH BLADE BACKSHELL F ⌀DIM R �DIM M� F MIN PASS-THRU WITH NO CLEARANCE E E OVERALL MATED SYSTEM WITH RECEPTACLE BACKSHELL �84.75� D D ⌀DIM S MIN PASS-THRU WITH NO CLEARANCE C C BLADE SEALED ASSEMBLY WITH BLADE BACKSHELL SYMBOLS B = 0 = 0 = 0 A FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 RELEASE DATE 17 16 2018/10/04 15:02:02 15 14 13 12 11 10 9 8 7 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 0 C MM ONLY 2:1 ± = 0 P1 SCALE ANGULAR TOL = 0 DOCUMENT STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 602373 DRWN: DSHETTY01 CHK'D: MVANSLAMBROU APPR: MVANSLAMBROU INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 5 2018/05/25 2018/10/04 2018/10/04 2015/07/21 2016/06/14 DRAWING SERIES A1-SIZE 33481 4 MX150 BLADE SINGLE ROW SEALED ASSY MAT SEAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-0001 MATERIAL NUMBER SEE NOTE 2a. 3 PSD 001 CUSTOMER GENERAL MARKET 2 A1 SHEET NUMBER 9 OF 9 1 A 20 M 19 18 17 16 15 14 13 12 11 10 9 7 8 SHEET DESCRIPTION 1 NOTES 2 KEY CONFIGURATIONS 3 BLADE SEALED ASSEMBLY L 4 SYSTEM PACKAGING 5 BOM 4 3 2 1 M TABLE OF CONTENTS SHEET NO. 5 6 NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-33472-100 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY CHECKING, CRIMPING, AND TROUBLESHOOTING. -DESIGNED TO MATE WITH RECEPTACLE SEALED ASSEMBLY SPECIFIED IN MOLEX DRAWING SD-33471-061. -FOR 1.5mm BLADE TERMINALS TO BE USED WITH THIS ASSEMBLY SEE MOLEX DRAWING SD-33000-001. - SYSTEM TO BE USED WITH WIRE WITHIN DIAMETER RANGE OF 1.2mm TO 2.69mm. -ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION -IN THE EVENT THAT THE PLR IS FOUND IN THE SEATED (FINAL LOCK) POSITION, REFER TO MOLEX SPECIFICATION PS-34646-001, AVAILABLE AT www.molex.com -ASSEMBLY CONFORMS TO SAE/USCAR-2 REV.4 WITH THE FOLLOWING EXCEPTIONS: TERMINAL INSERTION FORCE FOR WIRE DIAMETER ABOVE 2.5mm NOT EXCEEDING 2.69mm SHALL NOT EXCEED 45 NEWTONS. b. PRODUCT SPECIFICATION SEE: PS-33471-000 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY), AND PRODUCT VALIDATION. c. PACKAGING SPECIFICATION PER MOLEX DRAWING: PK-31300-635 d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR PRODUCTS AND PACKAGING SPECIFICATION: ES-40000-5016 e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) K GROMMET CAP J L K J 2. DESIGN - MATERIALS: a. CONNECTOR HOUSING, GROMMET CAP, PLR: SPS/NYLON BLEND 20% GLASS FILLED b. MAT SEAL: INHERENTLY LUBRICATED SILICONE MAT SEAL 3. DESIGN - GEOMETRY: a. THIS IS A 100% CAD GENERATED PART. THE CAD MATHEMATICAL DATA IS THE MASTER FOR THIS PART. FOR DIMENSIONAL OR ANY INFORMATION NOT SHOWN ON THIS DRAWING, ANALYZE THE CAD MODEL. b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M - 1994 c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715 d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX. e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD. THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION, AND CUSTOMER MATERIAL NUMBER. f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B) g. LASER MARKING: TBD H CONNECTOR HOUSING FOR OPTIONS SEE BOM H G G F F PRIMARY LOCK REINFORCEMENT (PLR) ADD NEW P/N 33481-6625 TO 33481-6626 V6 E E CHANGED PARTS STATUS TO "NOT RECOMMENDED" FOR SINGLE ROW BLADE V5 MAT SEAL CHANGE UPDATE 33481-0602/0607/0612/0618/0619 STATUS TO "SALEABLE" AND UPDATE V4 D INSPECTION NUMBER LOG LAST NUMBER USED: 8 ADDED: REMOVED: C 33481-0603/0604/0608/0609/0613/0614 STATUS TO "NOT RECOMMENDED" ON SHEET 5; UPDATE 33481-6602/6607/6612/6618/6619 STATUS TO "SALEABLE" AND UPDATE 33481-6603/6604/6608/6609/6613/6614 STATUS TO "NOT RECOMMENDED" ON SHEET 5; ADD NEW P/N 33481-6601 TO 33481-6624 V3 D ADD NEW P/N 33481-0624 V2 ADD NEW P/N 33481-0623 V1 ADD NEW P/N 33481-0621 33481-0622 U ADD NEW P/N 33481-0620 T S UPDATED GROMMET CAP R1 UPDATED DIMENSIONS TO MATCH MODEL COLOR REPLACEMENT FOR KEY C AND D PER USCAR STANDARD R Q REDRAWN REV DESCRIPTION THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/02/03 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:29:05 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 654141 DRWN: SCV CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 2021/01/29 2021/02/03 2021/02/03 DRAWING 5 2005/08/26 2005/08/29 SERIES 33481 DOC TYPE DOC PART REVISION SD-33481-061 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 V6 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X6 BLADE SEALED ASSEMBLY MAT SEAL 2 1 OF 5 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 M 2 1 M KEY CONFIGURATIONS 60° L 60° L K K KEY A J J 30° 60° H H G G KEY B 30° 60° F F E E KEY C D D 30° 30° C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 4:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B KEY D A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/02/03 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:29:05 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 654141 DRWN: SCV CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 2021/01/29 2021/02/03 2021/02/03 DRAWING 5 2005/08/26 2005/08/29 SERIES 33481 DOC TYPE DOC PART REVISION SD-33481-061 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 V6 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X6 BLADE SEALED ASSEMBLY MAT SEAL 2 2 OF 5 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M BLADE SEALED ASSEMBLY ⌀31.71 MIN PASS-THRU WITH NO CLEARANCE L LASER MARKING THIS SURFACE Y SEE NOTE 3g. Z TERMINAL POSITION 6 L TERMINAL POSITION 1 K K 2 17.13+0.10 -0.55 D D J J Y 5X 3.50 3 4 A 1 Z 53.85±0.60 29.44+0.25 -0.20 REAR VIEW (WIRE HARNESS SIDE) H H G G 2.00 7 +0.20 6 11.00-0.10 F F E E 6.60 15.00 5 8 SECTION D-D D C D THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 4:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B PRIMARY LOCK REINFORCEMENT (PLR) SHOWN PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN FINAL-LOCK POSITION IN PRE-STAGED POSITION SECTION Y-Y SECTION Z-Z A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/02/03 17 15 14 13 12 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:29:05 16 ANGULAR TOL 11 10 9 8 7 EC NO: 654141 DRWN: SCV CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 2021/01/29 2021/02/03 2021/02/03 DRAWING 5 2005/08/26 2005/08/29 SERIES 33481 DOC TYPE DOC PART REVISION SD-33481-061 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 V6 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X6 BLADE SEALED ASSEMBLY MAT SEAL 2 3 OF 5 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 M 2 1 M SYSTEM PACKAGING L L K K J J ⌀35.38 MIN PASS-THRU WITH NO CLEARANCE (72.71) OVERALL MATED SYSTEM H H G G F F E E D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 4:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/02/03 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:29:05 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 654141 DRWN: SCV CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 2021/01/29 2021/02/03 2021/02/03 DRAWING 5 2005/08/26 2005/08/29 SERIES 33481 DOC TYPE DOC PART REVISION SD-33481-061 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 V6 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X6 BLADE SEALED ASSEMBLY MAT SEAL 2 4 OF 5 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 BOM SHEET 1 M ASSEMBLY PART NUMBER K J H OPTION 1 2 3 4 5 ASSEMBLY PART NUMBER COMMENTS STATUS 6 SALEABLE NOT RECOMMENDED 33481-6620 BLACK X NOT RECOMMENDED 33481-6621 ST.GRAY D X X NOT RECOMMENDED 33481-6622 ST.GRAY D X NOT RECOMMENDED 33481-6623 BLACK A X NOT RECOMMENDED 33481-6624 BLACK A V6 33481-6625 BLACK A V6 33481-6626 BLACK A NOT RECOMMENDED 33481-0620 BLACK 33481-0621 ST.GRAY D X 33481-0622 ST.GRAY D X 33481-0623 BLACK A X 33481-0624 BLACK A NOT RECOMMENDED, SEE P/N 33481-0619 X NOT RECOMMENDED X NOT RECOMMENDED X NOT RECOMMENDED X NOT RECOMMENDED X X NOT RECOMMENDED X X NOT RECOMMENDED X X NOT RECOMMENDED X X NOT RECOMMENDED X X NOT RECOMMENDED X NOT RECOMMENDED X NOT RECOMMENDED X X X X X X X X G COMMENTS 6 D A D A NOT RECOMMENDED NOT RECOMMENDED X 5 33481-6619 33481-0619 NOT RECOMMENDED, SEE P/N 33481-0618 X X 4 SALEABLE NOT RECOMMENDED NOT RECOMMENDED NOT RECOMMENDED X 3 C C NOT RECOMMENDED X 1 2 STATUS DK.GRAY ST.GRAY DK.GRAY ST.GRAY 33481-6601 33481-6602 33481-6603 33481-6604 33481-6605 33481-6606 33481-6607 33481-6608 33481-6609 33481-6610 33481-6611 33481-6612 33481-6613 33481-6614 33481-6615 33481-6616 33481-6617 33481-6618 NOT RECOMMENDED X OPTION CAVITY TYPE & STATUS ( X = PLUGGED) A B C D A A B C D A A B C D A A A A B C D A A B C D A A B C D A A A X COLOR KEYING BLACK LT.GRAY BROWN GREEN YELLOW BLACK LT.GRAY BROWN GREEN YELLOW BLACK LT.GRAY BROWN GREEN YELLOW BLACK BLACK BLACK LT.GRAY BROWN GREEN YELLOW BLACK LT.GRAY BROWN GREEN YELLOW BLACK LT.GRAY BROWN GREEN YELLOW BLACK BLACK 33481-0601 33481-0602 33481-0603 33481-0604 33481-0605 33481-0606 33481-0607 33481-0608 33481-0609 33481-0610 33481-0611 33481-0612 33481-0613 33481-0614 33481-0615 33481-0616 33481-0617 33481-0618 L KEYING COLOR CAVITY TYPE & STATUS ( X = PLUGGED) M SALEABLE L SALEABLE NOT RECOMMENDED NOT RECOMMENDED, SEE P/N 33481-6618 NOT RECOMMENDED NOT RECOMMENDED, SEE P/N 33481-6619 SALEABLE X SALEABLE X SALEABLE X NOT RECOMMENDED X NOT RECOMMENDED X SALEABLE X X SALEABLE X X SALEABLE X X NOT RECOMMENDED X X NOT RECOMMENDED X X SALEABLE X SALEABLE X X X X X X X SALEABLE X X X X X SALEABLE X SALEABLE X X X J SALEABLE X X K H SALEABLE SALEABLE X X X SALEABLE X X SALEABLE G F F E E D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 1:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/02/03 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:29:05 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 654141 DRWN: SCV CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 2021/01/29 2021/02/03 2021/02/03 DRAWING 5 2005/08/26 2005/08/29 SERIES 33481 DOC TYPE DOC PART REVISION SD-33481-061 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 V6 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X6 BLADE SEALED ASSEMBLY MAT SEAL 2 5 OF 5 1 A