0345111001

19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 L L ASSEMBLY PART NO. K TPA PART NO. CONNECTOR HOUSING NO. TERMINAL HOUSING PART NUMBER COLOR KEYING OPTION NUMBER OF PLUGGED POSITIONS 34511-1001 34514-0001 34512-0003 34513-0001 BLACK A 0 34511-1002 34514-0002 34512-0003 34513-0002 LIGHT GRAY B 0 34511-1003 34514-0003 34512-0003 34513-0003 BROWN C 0 34511-1004 34514-0004 34512-0003 34513-0004 DARK GRAY D 0 CAVITY STATUS (X = PLUGGED) 1 2 3 4 TOOLED (4.8) X (1.6) (4.8) (1.6) K J J KEYING OPTION A KEYING OPTION C KEYING OPTION B KEYING OPTION D H H CONNECTOR HOUSING BLACK SEE CHART CAVITY ID TERMINAL POSITION # 4 SEE NOTE 6 TERMINAL POSITION # 1 (1.10) MATTE SEAL LIGHT BLUE 34516-0001 G TERMINAL HOUSING SEE CHART PERIMETER SEAL GREEN 34515-0001 F LOCATION CODE (32.2) TPA IN PRE-LOCK SEE NOTE 4 (0.50) REAR VIEW (WIRE HARNESS SIDE) DETAIL Z SCALE 20:1 1. MATERIAL PLASTIC: GLASS FILLED SPS RESIN SEALS: SILICONE 4.00 ( ⌀27.50MIN PASS-THRU ) PART NUMBER E (17.89) 3. DESIGNED TO MATE WITH HIRSCHMANN DRAWING 872-975-XXX VARIANTE 1 WITH FORM 1 BLADES ON DRAWING 1 99 51 50733 1. (28.7) TPA IN FINAL LOCK SEE NOTE 4 4. ASSEMBLY SHIPPED WITH TPA IN PRE-LOCK POSITION. EACH TPA MUST BE SNAPPED INTO FINAL LOCK POSITION UPON FULL TERMINAL ASSEMBLY. D (25.5) TRACEABILITY MARKINGS 5. SYSTEM TO BE USED WITH SAE 18 AWG, 20 AWG AND 22 AWG WIRES WITH DIAMETERS IN THE RANGE OF 1.5 MM TO 2.13 MM. C DATE CODE SEE DETAIL Z 2. FOR RECEPTACLE TERMINAL TO BE USED WITH THIS ASSEMBLY SEE MOLEX DRAWING SD-33468-001. TERMINAL BOX AND CRIMP SHOULD BE PARALLEL TO EACH OTHER WITHIN ONE DEGREE (1°) TO PREVENT TERMINAL STUBBING. D F TPA NATURAL SEE CHART NOTES: UNLESS OTHERWISE SPECIFIED. E G C 6. TO PREVENT TERMINAL BEAM DAMAGE, USE RECTANGULAR FLAT TIPPED PROBES FOR TERMINAL PROBING. 7. TPA FORCES A. ENGAGEMENT FORCE - WITH TERMINALS (PRE-LOCK TO FINAL-LOCK): 70 N MAX B. DISENGAGEMENT FORCE - WITH TERMINALS (FINAL-LOCK TO PRE-LOCK): 15N MIN THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 8. FOR RECYCLING INFORMATION CONTACT MOLEX. 9. SHALL CONFORM TO THE FOLLOWING PACKAGING SPECIFICATION NUMBER: PK-31300-163 10. FINISHED ASSEMBLIES TO BE MARKED WITH DATE CODE AND PART NUMBER. 11. TPA'S MAY BECOME SEATED DURING TRANSIT. IF THIS OCCURS, TPA'S SHOULD BE MOVED TO THE PRE-LOCKED POSITION PRIOR TO FEMALE TERMINAL INSTALLATION. 12. FORCE TO BE APPLIED TO SECONDARY LOCK FOR CAVITY DAMAGE SUSCEPTIBILITY TESTING (USCAR 5.4.9) TO BE 60 N. DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2019/11/12 16 14 mm 2:1 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° 13 CURRENT REV DESC: OBSOLETED PART NO 12 11 10 9 8 7 B EC NO: 625872 DRWN: AKUMAR19 CHK'D: GB APPR: GGA INITIAL REVISION: DRWN: BFLOWERS APPR: SMARCEAU DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:17:57 15 SCALE GENERAL TOLERANCES (UNLESS SPECIFIED) B A DIMENSION UNITS 6 THIRD ANGLE PROJECTION 5 CONNECTOR ASSEMBLY 4 CKT 1.2 MM SEALED 2019/06/12 2019/11/06 2019/11/12 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2004/04/12 2004/04/13 DRAWING SERIES D-SIZE 34511 4 SD-34511-001 MATERIAL NUMBER SEE TABLE 3 PSD 001 L1 SHEET NUMBER CUSTOMER GENERAL MARKET 2 1 OF 1 1 A