0424920304

5 6 4 3 2 1 DIM. A REF. D CENTERLINE OF PIN AT TIP NOT TO VARY FROM CENTERLINE OF PIN AT DATUM -DBY MORE THAN 0.20/.008 IN ANY DIRECTION. 2.41 .095 1.91 TYP .075 DIM. B 3.96 REF. .156 TYP. BETWEEN ANY 2 CONSECUTIVE CIRCUITS AT DATUM -D- 5.11 .201 D CIRCUIT 1 SEE NOTE 10 FEATURE MAY BE ON EITHER SIDE OF PART GOLD M 11.33±0.51 .446±.020 ±0.38 ±.015 SEE PEG DETAIL SHEET 2 TYP. 3.30 .130 Y TYP. C 1.14 L TYP. REF. .045 NO. OF CKTS. SQ. PINS 2 TIN 10.01±0.51 .394±.020 CENTERLINE OF PIN AT TIP NOT TO VARY FROM CENTERLINE OF PIN AT DATUM -DBY MORE THAN 0.20/.008 IN ANY DIRECTION. 3 VOIDED CIRCUIT SEE CHART FOR LOCATION 4 5 DIM. P TYP.REF. 6 7 8 B 9 10 11 12 DIM. A 7.77 .306 11.73 .462 15.70 .618 19.66 .774 23.62 .930 27.58 1.086 31.55 1.242 35.51 1.398 39.47 1.554 43.43 1.710 47.40 1.866 DIM. B SLOT LOC BETWEEN CKTS 3.96±0.05 .156±.002 7.92±0.08 .312±.003 11.89±0.08 .468±.003 15.85±0.10 .624±.004 19.81±0.10 .780±.004 23.77±0.10 .936±.004 27.74±0.13 1.092±.005 31.70±0.13 1.248±.005 35.66±0.13 1.404±.005 39.62±0.15 1.560±.006 43.59±0.15 1.716±.006 C NONE NONE NONE NONE 3&4 4&5 4&5 B 5&6 5&6 6&7 4&5 8&9 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± A 3 PLACES ± ± 0.25 ± 0.015 ± 0.38 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 6 P1 RELEASE DATE 2019/03/15 5 0.01 2 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 INCH ± ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 7 5 6 3 2 3.96±0.05 .156±.002 TYP NON-ACCUM. CL OF RIB 0.94±0.05 .037±.002 TYP 3 D 4 1 1.70±0.05 .067±.002 DIA TYP 0.20 TYP 3 REF .008 D Y +0.66±0.05 Y +.026±.002 18.25° ⌀ CL 1.63±0.05 DIA. TYP. (2) .064±.002 HOLES FOR PEGS MUST NOT HAVE SOLDER PADS OR PLATED THRU HOLES. 1.98±0.05 .078±.002 1.32 .052 REF PEG DETAIL SCALE 10:1 RECOMMENDED PC BOARD HOLE LAYOUT C B A NOTES: 1. MATERIAL: HEADER-POLYESTER, 94V-0, MOLDED NATURAL (WHITE) PINS: BRASS 2. FINISHES: (154) OVERALL TIN 0.00254/.000100 MIN. OVER 0.00127/.000050 MIN. NICKEL. (197) OVERALL REFLOWED MATTE TIN: 0.00152/.000060 MIN. OVER 0.00127/.000050 MIN. NICKEL OVERALL. (208) SELECT GOLD 0.00038/.000015 MIN. SELECT TIN 0.00254/.000100 MIN. OVERALL NICKEL UNDERPLATE 0.00127/.000050 MIN. (228) SELECT GOLD 0.00076/.000030 MIN. SELECT TIN 0.00254/.000100 MIN. OVERALL NICKEL UNDERPLATE 0.00127/.000050 MIN. (241) SELECT GOLD: 0.00051/.000020 MIN. SELECT TIN: 0.00254/.000100 MIN. OVERALL NICKEL UNDERPLATE: 0.00127/.000050 MIN. 3. PRODUCT SPECIFICATION: SEE PS-08-50. 4. PACKAGING INFO: SEE TABLES. 5. SOLDERABILITY: PER SMES-152. 6. PIN PUSH OUT FORCE: PRIOR TO SOLDERING, A 3 LB MINIMUM FORCE (IN EITHER DIRECTION) SHALL BE REQUIRED TO PUSH THE PIN OUT OF THE HEADER. 7. PARTS ARE STACKABLE END TO END ON 3.96/.156 CENTERS. 8. FOR PART WITHOUT PEGS SEE 41792. 9. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 10. SLOTS ON BACKWALL ARE BETWEEN CIRCUITS. SEE CHART FOR LOCATION. B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 1:1 MM 4 PLACES ± 6 P1 RELEASE DATE 2019/03/15 5 INCH ± 3 PLACES ± ± 0.01 2 PLACES ± 0.25 ± 0.015 ± 0.38 ± 1 PLACE ANGULAR TOL DOCUMENT STATUS CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) 0 PLACES ± FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 C EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 7 5 6 OPTIONS D Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Ckts Material No 2 26-64-5020 3 26-64-5030 4 26-64-5040 5 26-64-5050 6 26-64-5060 7 26-64-5070 8 26-64-5080 9 26-64-5090 10 26-64-5100 11 26-64-5110 12 26-64-5120 13 14 15 16 17 18 C B A-42492-0002/0018 41790-0036/0052 43294-0572 197 – TIN 27.94/1.100 11.43 / .450 N/A 5.41/ .213 3.96 / .156 OVERALL NONE PK-42492-002 Engineer Number A-42492-0002 A-42492-0003 A-42492-0004 A-42492-0005 A-42492-0006 A-42492-0007 A-42492-0008 A-42492-0009 A-42492-0010 A-42492-0011 A-42492-0012 4 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 42492-0319 42492-0320 42492-0321 42492-0322 42492-0323 42492-0324 42492-0325 42492-0326 42492-0327 42492-0328 42492-0329 3 A-42492-0319/0335 41790-0036/0052 43294-0569 208 – 15 GOLD 27.94/1.100 11.43/.450 6.86/. 270 5.41/ .213 3.96/ .156 5.08 / .200 NONE PK-42492-002 Engineer Number A-42492-0319 A-42492-0320 A-42492-0321 A-42492-0322 A-42492-0323 A-42492-0324 A-42492-0325 A-42492-0326 A-42492-0327 A-42492-0328 A-42492-0329 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 42492-0336 42492-0337 42492-0338 42492-0339 42492-0340 42492-0341 42492-0342 42492-0343 42492-0344 42492-0345 42492-0346 2 A-42492-0336/0352 41790-0036/0052 43294-0570 228 – 30 GOLD 27.94/1.100 11.43/.450 6.86/. 270 5.41/ .213 3.96/.156 5.08 / .200 NONE PK-42492-002 Engineer Number A-42492-0336 A-42492-0337 A-42492-0338 A-42492-0339 A-42492-0340 A-42492-0341 A-42492-0342 A-42492-0343 A-42492-0344 A-42492-0345 A-42492-0346 1 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No D Engineer Number C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± A 3 PLACES ± ± 0.25 ± 0.015 ± 0.38 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 6 P1 RELEASE DATE 2019/03/15 5 0.01 2 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 INCH ± ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 3 OF 7 5 6 OPTIONS D Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Ckts Material No 2 3 4 26-64-5042 5 26-64-5052 6 26-64-5062 7 26-64-5072 8 26-64-5082 9 26-64-5092 10 26-64-5102 11 26-64-5112 12 26-64-5122 13 14 15 16 17 18 C B A-42492-0036/0050 41790-0038/0052 43294-0572 197 – TIN 27.94/1.100 11.43 / .450 N/A 5.41/ .213 3.96 / .156 OVERALL 4 PK-42492-002 Engineer Number A-42492-0036 A-42492-0037 A-42492-0038 A-42492-0039 A-42492-0040 A-42492-0041 A-42492-0042 A-42492-0043 A-42492-0044 4 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 26-64-5061 26-64-5071 26-64-5081 26-64-5091 26-64-5101 26-64-5111 26-64-5121 3 2 A-42492-0244/0256 41790-0040/0052 43294-0572 197 – TIN 27.94/1.100 11.43/.450 N/A 5.41/ .213 3.96/ .156 OVERALL 6 PK-42492-002 Engineer Number Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided CKts Pack Per Material No A-42492-0258/0273 41790-0037/0052 43294-0572 197 – TIN 27.94/1.100 11.43/.450 N/A 5.41/ .213 3.96/.156 OVERALL 2 PK-42492-002 Engineer Number A-42492-0244 A-42492-0245 A-42492-0246 A-42492-0247 A-42492-0248 A-42492-0249 A-42492-0250 26-66-0031 26-66-0041 26-66-0051 26-66-0061 26-66-0071 26-66-0081 26-66-0091 26-66-0101 26-66-0111 26-66-0121 A-42492-0258 A-42492-0259 A-42492-0260 A-42492-0261 A-42492-0262 A-42492-0263 A-42492-0264 A-42492-0265 A-42492-0266 A-42492-0267 1 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No A-42492-0274/0288 41790-0038/0052 43294-0573 241 - GOLD 27.94/1.100 11.43/.450 6.85/ .270 5.41/ .213 3.96/.156 5.08/ .200 4 PK-42492-002 Engineer Number D C 42492-0274 42492-0275 42492-0276 42492-0277 42492-0278 42492-0279 42492-0280 42492-0281 42492-0282 A-42492-0274 A-42492-0275 A-42492-0276 A-42492-0277 A-42492-0278 A-42492-0279 A-42492-0280 A-42492-0281 A-42492-0282 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± A 3 PLACES ± ± 0.25 ± 0.015 ± 0.38 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 6 P1 RELEASE DATE 2019/03/15 5 0.01 2 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 INCH ± ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 4 OF 7 5 6 OPTIONS D Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Ckts Material No 2 3 4 5 42492-0289 6 42492-0290 7 42492-0291 8 42492-0292 9 42492-0293 10 42492-0294 11 42492-0295 12 42492-0296 13 14 15 16 17 18 C B 4 3 A-42492-0289/0302 41790-0039/0052 43294-0572 197 – TIN 27.94/1.100 11.43 / .450 N/A 5.41/ .213 3.96 / .156 OVERALL 5 PK-42492-002 Engineer Number Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No A-42492-0303/0318 41790-0037/0052 43294-0572 197 – TIN 27.94/1.100 11.43/.450 N/A 5.41/ .213 3.96/ .156 OVERALL 3 PK-42492-002 Engineer Number A-42492-0289 A-42492-0290 A-42492-0291 A-42492-0292 A-42492-0293 A-42492-0294 A-42492-0295 A-42492-0296 42492-0303 42492-0304 42492-0305 42492-0306 42492-0307 42492-0308 42492-0309 42492-0310 42492-0311 42492-0312 A-42492-0303 A-42492-0304 A-42492-0305 A-42492-0306 A-42492-0307 A-42492-0308 A-42492-0309 A-42492-0310 A-42492-0311 A-42492-0312 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided CKts Pack Per Material No 26-65-5020 26-65-5030 26-65-5040 26-65-5050 26-65-5060 26-65-5070 26-65-5080 26-65-5090 26-65-5100 26-65-5110 26-65-5120 2 A-42492-0019/0035 41790-0036/0052 43294-0573 241 - GOLD 27.94/1.100 11.43/.450 6.85/ .270 5.41/ .213 3.96/.156 5.08/ .200 NONE PK-42492-002 Engineer Number A-42492-0019 A-42492-0020 A-42492-0021 A-42492-0022 A-42492-0023 A-42492-0024 A-42492-0025 A-42492-0026 A-42492-0027 A-42492-0028 A-42492-0029 1 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 42492-0400 42492-0401 42492-0402 42492-0403 42492-0404 42492-0405 42492-0406 42492-0407 42492-0408 42492-0409 42492-0410 A-42492-0400/0416 41790-0036/0052 43294-0500 197 - TIN 26.16/ 1.030 11.38/.448 N/A 5.41/ .213 2.23/ .088 OVERALL NONE PK-42492-002 Engineer Number A-42492-0400 A-42492-0401 A-42492-0402 A-42492-0403 A-42492-0404 A-42492-0405 A-42492-0406 A-42492-0407 A-42492-0408 A-42492-0409 A-42492-0410 D C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± A 3 PLACES ± ± 0.25 ± 0.015 ± 0.38 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 6 P1 RELEASE DATE 2019/03/15 5 0.01 2 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 INCH ± ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 5 OF 7 5 6 OPTIONS D Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Ckts Material No 2 3 4 42492-0417 5 42492-0418 6 42492-0419 7 42492-0420 8 42492-0421 9 42492-0422 10 42492-0423 11 42492-0424 12 42492-0425 13 14 15 16 17 18 C B A-42492-0417/0431 41790-0036/0052 43294-0572 197 – TIN 27.94/1.100 11.43 / .450 N/A 5.41/ .213 3.96 / .156 OVERALL 2, 4 PK-42492-002 Engineer Number 4 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 3 A-42492-0432/0443 41790-0041/0052 43294-0572 197 – TIN 27.94/1.100 11.43/.450 N/A 5.41/ .213 3.96/ .156 OVERALL 1,4,5,6,7 PK-42492-002 Engineer Number Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided CKts Pack Per Material No 2 A-42492-0444/0456 41790-0040/0052 43294-0572 197 – TIN 27.94/1.100 11.43/.450 N/A 5.41/ .213 3.96/.156 OVERALL 3, 6 PK-42492-002 Engineer Number 1 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No A-42492-0461/0473 41790-0040/0052 43294-0572 197 – TIN 27.94/1.100 11.43/.450 N/A 5.41/ .213 3.96/.156 OVERALL 4, 6 PK-42492-002 Engineer Number D C A-42492-0417 A-42492-0418 A-42492-0419 A-42492-0420 A-42492-0421 A-42492-0422 A-42492-0423 A-42492-0424 A-42492-0425 42492-0432 42492-0433 42492-0434 42492-0435 42492-0436 42492-0437 42492-0444 42492-0445 42492-0446 42492-0447 42492-0448 42492-0449 42492-0450 A-42492-0432 A-42492-0433 A-42492-0434 A-42492-0435 A-42492-0436 A-42492-0437 A-42492-0444 A-42492-0445 A-42492-0446 A-42492-0447 A-42492-0448 A-42492-0449 A-42492-0450 42492-0462 A-42492-0462 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± A 3 PLACES ± ± 0.25 ± 0.015 ± 0.38 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 6 P1 RELEASE DATE 2019/03/15 5 0.01 2 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 INCH ± ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 6 OF 7 5 6 OPTIONS D Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Ckts Material No 2 3 4 5 6 7 42492-0474 8 9 10 11 12 13 14 15 16 17 18 C B A-42492-0474 41790-0040/0052 43294-0571 154 – TIN 27.94/1.100 11.43 / .450 N/A 5.41/ .213 3.96 / .156 OVERALL 2, 5, 6 PK-42492-002 Engineer Number 4 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 3 A-42492-0490 41790-0037/0052 43294-0569 208 – 15 GOLD 27.94/1.100 11.43/. 450 6.86/.270 5.41/ .213 3.96/ .156 5.08 / .200 3 PK-42492-002 Engineer Number Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No 2 1 Group Header No: Pin No: Plating: Pin Length L Mating M Gold Loc G Dim. Y PC Tail P Tin Loc T Voided Ckts Pack Per Material No Engineer Number D Engineer Number C A-42492-0474 42492-0490 A-42492-0490 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: REMASTERED IN NX GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± A 3 PLACES ± ± 0.25 ± 0.015 ± 0.38 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 6 P1 RELEASE DATE 2019/03/15 5 0.01 2 PLACES ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-A REVISION: D DATE: 2018/01/18 INCH ± ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:07:15 4 EC NO: 613774 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: JSCHAFER APPR: MARGULIS THIRD ANGLE PROJECTION 3 KK .156 HEADER ASSEMBLY FRICTION LOCK RT ANGLE WITH PEGS 2019/03/08 2019/03/15 2019/03/15 A PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 11-25-03 12-1-03 DRAWING SERIES A-SIZE 42492 SD-42492-001 MATERIAL NUMBER SEE CHART 2 PSD 001 G2 SHEET NUMBER CUSTOMER GENERAL MARKET 1 7 OF 7