0430450217

12 11 10 9 7 8 5 6 4 D (SEE NOTE 8) C .085±.002 2.15±0.05 H B 3 2 ±.003 ±0.08 ±.004 02 ±0.10 04 06 LAST CIRCUIT 08 .095±.002 2.41±0.05 TYP SEE NOTE #6 A .010 TYP 0.25 (SEE NOTE 8) B .390 9.91 .055 1.40 .118 3.00 .270 6.86 14 16 18 CIRCUIT 1 .085 2.16 .050 TYP 1.27 .135 3.43 .118 3.00 12 .100 TYP 2.54 LAST CIRCUIT F 10 .135±.002 3.43±0.05 .08 2.0 20 CIRCUIT 2 22 PCB LAYOUT: COMPONENT SIDE RECOMMENDED PCB THICKNESS: .062/1.57 .44 11.2 .290 7.37 A CKTS .118±.004 3.00±0.10 NON-ACCUM G 1 24 .262 6.65 .380 9.65 .498 12.65 .616 15.65 .734 18.65 .852 21.65 .970 24.65 1.088 27.65 1.206 30.65 1.325 33.65 1.443 36.65 1.561 39.65 B C .169 4.30 .287 7.30 .405 10.30 .524 13.30 .642 16.30 .760 19.30 .878 22.30 .996 25.30 1.114 28.30 1.232 31.30 1.350 34.30 1.469 37.30 NA .118 3.00 .236 6.00 .354 9.00 .472 12.00 .591 15.00 .709 18.00 .827 21.00 .945 24.00 1.063 27.00 1.181 30.00 1.299 33.00 E H G F E CIRCUIT 1 .025 0.64 SQ TYP CIRCUIT 2 D (SEE NOTE 8) .006 MAX 0.15 CIRCUIT "1" IDENTIFIED ON THIS SURFACE. (APPROX. LOCATION SHOWN FOR REF.) NOTES: FINISH 1. HOUSING MATERIAL: GLASS FILLED LIQUID CRYSTAL POLYMER, UL94V-0, COLOR: BLACK TERMINAL MATERIAL: BRASS ALLOY D 2. FINISH: A = .000060/(0.00152) MIN. REFLOW MATTE TIN OVER .000050/(0.00127) MIN. NICKEL PLATE. (FINISH IS BRIGHT IN APPEARANCE, THICKNESS AS APPLIED PRIOR TO REFLOW) B = .000015/(0.00038) MIN. SELECT GOLD IN CONTACT AREA; .000100/(0.00254) MIN. SELECT MATTE TIN ON SOLDER TAILS; BOTH OVER .000050/(0.00127) MIN. NICKEL PLATE. C C = .000030/(0.00076) MIN. SELECT GOLD IN CONTACT AREA; .000100/(0.00254) MIN. SELECT MATTE TIN ON SOLDER TAILS; BOTH OVER .000050/(0.00127) MIN. NICKEL PLATE. D = .000100/(0.00254) MIN. MATTE TIN OVER .000050/(0.00127) MIN. NICKEL PLATE 3. PRODUCT SPECIFICATION: PS-43045 4. TAPE AND REEL PACK : SEE MOLEX DRAWING 430450002-PK 5. MATES WITH MICRO FIT (3.0) RECEPTACLE SERIES 43025 B MATERIAL NO: MATERIAL NO: MATERIAL NO: 02 43045-0215 43045-0216 43045-0217 43045-0320 04 43045-0415 43045-0416 43045-0417 43045-0520 06 43045-0615 43045-0616 43045-0617 43045-0720 08 43045-0815 43045-0816 43045-0817 43045-0920 10 43045-1015 43045-1016 43045-1017 43045-1120 12 43045-1215 43045-1216 43045-1217 43045-1320 14 43045-1415 43045-1416 43045-1417 43045-1520 16 43045-1615 43045-1616 43045-1617 18 43045-1815 43045-1816 43045-1817 43045-1720 43045-1920 20 43045-2015 43045-2016 43045-2017 43045-2120 22 43045-2215 43045-2216 43045-2217 43045-2320 24 43045-2415 43045-2416 43045-2417 43045-2520 SYMBOLS = 0 = 0 SCALE IN / MM NTS 9. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. = 0 1 PLACE 10. TEXT ON PART IS FOR REFERENCE ONLY. TEXT AND TEXT LOCATION MAY VARY DEPENDING ON PART NUMBER AND/OR TOOL. = 0 0 PLACES ± 2019/08/15 10 = 0 MM = 0 C 8 7 6 = 0 INCH 4 PLACES ± ± 3 PLACES ± ± 0.01 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± ANGULAR TOL 16:28:58 9 SHOWN WITH DISPOSABLE CAP (FOR REMOVAL FROM TAPE & REEL PACKAGING) SEE NOTE #4 CURRENT REV DESC: MICROFIT PK SPEC REF GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 RELEASE DATE 11 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 P1 D COPLANARITY DETAIL SEE NOTE #7 B 8. CIRCUIT SIZES 2-6: "D" IS 0.265/6.74 FOR .010/0.25 STEP. CIRCUIT SIZES 8-24: "D" IS .063/1.60 FOR .010/0.25 STEP. DOCUMENT STATUS 12 FINISH D MATERIAL NO: 7. THE COPLANARITY DIMENSION IS ESTABLISHED BY PLACING THE ASSEMBLY ON A FLAT SURFACE. THE DISTANCE FROM THAT SURFACE TO THE BOTTOM OF ANY TERMINAL MUST NOT EXCEED .006/0.15 FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 C FINISH CKTS 6. TO MINIMIZE INSERTION FORCE OF MOUNTING CLIPS DURING ROBOTIC PLACEMENT THE HOLE DIAMETER SHOULD BE INCREASED TO .108±.002 / 2.74±0.05 AND THEN EVALUATED PER PLACEMENT EQUIPMENT. A B FINISH A ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 611607 DRWN: SALHAMY CHK'D: SSOUSEK APPR: FSMITH INITIAL REVISION: DRWN: SAMIEC APPR: FSMITH THIRD ANGLE PROJECTION 4 2019/01/07 2019/08/09 2019/08/15 MICRO FIT (3.0) VERTICAL SMT CLIPS DUAL ROW HEADER / CAP / TAPE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2000/03/15 2016/08/03 DRAWING SERIES C-SIZE 43045 3 SD-43045-006 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 G5 SHEET NUMBER GENERAL MARKET 1 OF 1 1 A