0442821004

9 E D C 7 8 5 6 NOTES: 1) MATERIAL: HOUSING & INSULATOR: NYLON(PA), GLASS FILLED, UL94V-0, COLOR: BLACK TERMINALS: PHOSPHOR BRONZE, 0.30 mm THICK SHIELD: BRASS 2) FINISH: TERMINALS: A = SELECT GOLD IN CONTACT AREA: 0.00127 mm MIN., *SELECT MATTE TIN IN PC TAIL AREA: 0.00254 mm MIN., WITH OVERALL NICKEL UNDERPLATE: 0.00127 mm MIN. B = SELECT GOLD IN CONTACT AREA: 0.00076 mm MIN., *SELECT MATTE TIN IN PC TAIL AREA: 0.00254 mm MIN., WITH OVERALL NICKEL UNDERPLATE: 0.00127 mm MIN. C = SELECT GOLD IN CONTACT AREA: 0.00038 mm MIN., *SELECT MATTE TIN IN PC TAIL AREA: 0.00254 mm MIN., WITH OVERALL NICKEL UNDERPLATE: 0.00127 mm MIN. SHIELD: *2.54 MICROMETER NICKEL OVER 1.27 MICROMETER COPPER UNDERPLATE PCB GROUND TABS DIPPED IN TIN *THE PRIMARY SHIPPING CARTON WILL BE LABELED "COMPLIANT TO RoHS DIRECTIVE 2002/95/EC AND ELV ANNEX II OF DIRECTIVE 2000/53/EC". CARTONS WITHOUT THIS LABEL MAY CONTAIN PRODUCT WITH TIN-LEAD IN THE PC TAILS AND/OR SHIELD. 3) PRODUCT SPECIFICATION AND PROCESSING PARAMETERS: PS-43743-0001. 4) PACKAGING SPECIFICATION: CONNECTOR ASSEMBLIES TO BE PACKAGED USING TAPE & REEL SYSTEM PER PACKAGING DRAWING PK-70873-7006. 5 COPLANARITY SPECIFICATION: WHEN AN ASSEMBLY IS PLACED UPON A LEVEL SURFACE, THE MAXIMUM GAP BETWEEN THE LEVEL SURFACE AND ALL TERMINAL TAILS AND FRONT SOLDER TAB IS 0.15 mm. 6 THRU HOLES 2.39±0.05 mm ARE FOR SHIELDS WITH LOCATION TABS ONLY. 7 AVAILABLE WITH (4) OPTIONAL SIDE GROUND TABS (OMITTED FOR SIDE TO SIDE STACKABILITY). 8 AVAILABLE WITH (2) OPTIONAL LOCATION TABS FOR LOCATING COMPONENT TO PCB AND/OR GROUNDING TO PCB. 9) FOR ASSEMBLIES HAVING VOIDED CIRCUITS, THE TAIL PORTION IS CUT AND REMOVED. THE MATING PORTION OF THE TERMINAL REMAINS INTACT. 10) CONFORMS TO FCC REGULATION PART 68.5 FOR MODULAR JACKS. 11) THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 4 3 2 1 OPTIONAL TOP GROUND TABS (SEE CHART) SHIELDED SMT MODJACK ASSEMBLY E 13.45 REF 12.19 REF 0.83 TERMINAL TAILS OPTIONAL LOCATION/PCB GROUND TABS OPTIONAL SIDE GROUND 7 TABS (SEE CHART) FRONT SOLDER TAB 16.87 8 5 1.27 TYP(REF) TOL. NON-ACCUMULATIVE 3.81 +0.38 -0.00 D 5 C 13.08 +0.38 -0.00 R 0.64 TYP 18.55 REF 15.85 8.89 (REF) RECOMMENDED PANEL OPENING (2:1) 0.41 TYP(REF) B B X X X X X X X X X X X A 44282-1004 44282-0012 44282-0011 44282-0010 44282-0009 44282-0008 44282-0007 44282-0006 44282-0005 44282-0004 44282-0003 44282-0002 44282-0001 A C B A C B A C B A C B A NO NO NO NO YES YES YES NO NO NO YES YES YES NO YES YES YES YES YES YES YES YES YES YES YES YES YES NO NO NO NO NO NO YES YES YES YES YES YES NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE 17.60 44282-0001, 44282-0002 & 44282-0003 SHOWN SYMBOLS = 0 = 0 = 0 "X"=NOT ASSEMBLY TERMINAL SHIELD SHIELD LOCATION VOIDED TOOLED MAT. NO. PLATING SIDE TABS TOP TABS TABS CIRCUITS DOCUMENT STATUS 9 P1 RELEASE DATE 2018/03/23 8 C 7 6 5 4 SCALE MM 3:1 ± 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL = 0 01:56:29 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 = 0 FORMAT: master-tb-prod-A3 REVISION: H DATE: 2017/10/06 1.30 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS EC NO: 173578 DRWN: VK10 CHK'D: KLANG APPR: KLANG INITIAL REVISION: DRWN: STAMBAUG APPR: EDGLEY THIRD ANGLE PROJECTION 3 2018/01/18 2018/03/23 2018/03/23 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 99/06/03 99/06/03 SD-44282-001 MATERIAL NUMBER DRAWING SERIES A3-SIZE 44282 2 A SINGLE PORT, SHIELDED SIZE 8, 8 CIRCUIT SMT MODJACK SEE CHART PSD 001 D5 SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 2 9 7 8 5 6 4 3 2 1 TERMINAL CUTOFF POINT E E VIEW SHOWING TYPICAL TERMINAL CUTOFF OF TAIL (SEE NOTE 10) FOR VOIDED CIRCUITS. D D TYPICAL VIEW SHOWING VOIDED CIRCUIT (CIRCUITS 2,3,6 & 7 SHOWN VOIDED) 3.16 1.27±0.05 TYP. TOL. NOT ACCUMULATED 8.89 0.64 TYP C C 2.54 CKT. 1 ⌀ 2.39±0.05 TYP(2) (SEE NOTE 6 ) 15.24±0.08 17.60 16.48 B B 1.91 TYP(2) 6.35±0.08 P.C. BOARD EDGE 1.91 10.41 2.72 TYP(2) NOTES: 1. RECOMMENDED MINIMUM PCB THICKNESS: 0.86 mm. SYMBOLS 15.85 ASSY OUTLINE (SHIELDED) A = 0 = 0 PC BOARD LAYOUT FOR 8 POSITION HOUSING = 0 (COMPONENT SIDE OF BOARD) 9 P1 RELEASE DATE 2018/03/23 8 01:56:29 C 7 6 5 4 1:1 ± 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL = 0 DOCUMENT STATUS SCALE MM = 0 = 0 FORMAT: master-tb-prod-A3 REVISION: H DATE: 2017/10/06 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS EC NO: 173578 DRWN: VK10 CHK'D: KLANG APPR: KLANG INITIAL REVISION: DRWN: STAMBAUG APPR: EDGLEY THIRD ANGLE PROJECTION 3 2018/01/18 2018/03/23 2018/03/23 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 99/06/03 99/06/03 SD-44282-001 MATERIAL NUMBER DRAWING SERIES A3-SIZE 44282 2 A SINGLE PORT, SHIELDED SIZE 8, 8 CIRCUIT SMT MODJACK SEE CHART PSD 001 D5 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 2