0455703052

18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 NOTES: 1. MATERIAL: COPPER ALLOY; .011/(0.28) THICK. L ITEM NUMBER DESCRIPTION 45570-3000 K PLATING ON REEL 45570-3050 LOOSE 45570-3002 ON REEL 45570-3052 LOOSE 45570-3004 ON REEL 45570-3054 WIRE AWG. PRE-PLATE: HOT TIN DIP SEE NOTE 2.1 18 - 20 POST PLATE: TIN OVER NICKEL SEE NOTE 2.2 18 - 20 POST PLATE: TIN OVER NICKEL W/SELECT GOLD SEE NOTE 2.3 LOOSE DIM "A" ±.010/0.25 18 - 20 DIM "B" DIM "E" 2. PLATING OPTIONS: DIM "F" L 1. PRE-PLATE HOT TIN DIP .000080/(.00203) MINIMUM OVERALL. .164 .162 .102 .110 4.17 4.12 2.59 2.80 .164 .162 .102 .110 4.17 4.12 2.59 2.80 2. POST PLATE TIN .00020/(.00508) MINIMUM OVERALL OVER NICKEL .00005/(.00127) MINIMUM OVERALL. 3. POST PLATE SELECT TIN .00010/(.00250) MINIMUM AND SELECT GOLD .000030/(.00076) MINIMUM OVER NICKEL OVERALL .000050/(.00127) MINIMUM. 3. PRODUCT SPECIFICATION: PS-45570-001. 4. TERMINAL FOR USE IN HOUSING NUMBER 41695. K .164 .164 .102 .110 5. TERMINALS FOR USE WITH UL1015 STRANDED WIRE ONLY: MAXIMUM INSULATION RANGE 3.12/(.123). 4.17 4.12 2.59 2.80 6. FOR CRIMP INFORMATION SEE CRIMP SPECIFICATION ATS-63866-2000. 7. TERMINAL MATES TO MOLEX .156/3.96 HEADERS WITH .045/1.14 SQ. PIN. 8. PACKAGING SPECIFICATION: PK-2759-002 9. TEXT ON PART IS FOR REFERENCE ONLY. TEXT AND TEXT LOCATION MAY VARY DEPENDING ON PART NUMBER AND/OR TOOL. J J H H A .050 1.27 A B .170 4.32 B TO CRIMP PRESS M G SELECT TIN LOCATED WHEN REQUIRED G .157±.008 3.99±0.2 .511±.010 12.98±0.25 REEL WINDING DIRECTION FOR FINISHED PRODUCT .080±.008 2.03±0.2 SELECT GOLD AREA (INSIDE ONLY) WHEN REQUIRED F F .091 2.31 .006 MAX CUTOFF ALLOWED 0.15 TYP 2 E E .063 ⌀ 1.60 "A" .150 3.81 .450 11.43 "E" .12±.010 3.19±0.25 D SELECT TIN LOCATION WHEN REQUIRED MINIMUM .073 1.85 "B" "F" SELECT GOLD AREA (INSIDE ONLY) WHEN REQUIRED .800 20.32 C SECTION A-A SCALE 10:1 SECTION B-B SCALE 10:1 .055 1.40 B C TERMINAL - LOOSE SYMBOLS = 0 = 0 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE IN/MM 1:1 = 0 = 0 MM INCH 4 PLACES ± ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± = 0 1 PLACE = 0 0 PLACES ± A FORMAT: Met-lega-master-tb-prod-A1 REVISION: D DATE: 2018/01/18 18 P1 RELEASE DATE 17 16 2018/10/11 11:45:43 15 C 14 13 12 11 10 9 8 = 0 7 0.01 ± ± ANGULAR TOL = 0 CURRENT REV DESC: NOTE 8 UPDATED B GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 TERMINAL - ON CARRIER DOCUMENT STATUS D .079 2.01 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 EC NO: 605758 DRWN: SS06 CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: MMD APPR: AP THIRD ANGLE PROJECTION 5 TERMINAL, FEMALE CRIMP .156 CENTERS 2018/09/11 2018/10/11 2018/10/11 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER A 2003/04/29 2003/04/30 DRAWING SERIES A1-SIZE 45570 4 SD-45570-001 MATERIAL NUMBER SEE CHART 3 PSD 001 CUSTOMER GENERAL MARKET 2 G1 SHEET NUMBER 1 OF 1 1