0468310002

12 11 10 9 8 7 5 6 4 TERMINALS TO BE ORIENTED AND LOADED INTO THE HOUSING AS SHOWN BELOW 3 2 1 NOTES: 1. MATERIAL: HALOGEN-FREE PBT. COLOR: BLACK. 2. PRODUCT CONFORMS TO PRODUCT SPECIFICATION PS-45579-001. 3. USES MALE CRIMP TERMINALS SERIES 45627. 4. PART MATES WITH MOLEX RECEPTACLE 46528-0007. 5. PACKAGING: 2,500 PCS PER MOLEX SHIPPING CARTON 96707-0007. 6. SEE PAGE 2 OF 2 FOR PANEL CUTOUT DIMENSIONS AND THE ALLOWED PANEL TO PANEL MISALIGNMENT. 7. USE MOLEX EXTRACTION TOOL 63813-1400 TO REMOVE TERMINAL WITHOUT DAMAGING THE PLUG CORE. RELOAD PLUG CORE WITH NEW TERMINAL ONLY. REMOVED TERMINAL AFTER EXTRACTION IS NOT USABLE. H G H G 2.30 7.95 F F 13.00 0.77 TYP 1.50 E E 4.36 6.36 D D 2.50 1.52 2.30 C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM 4:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) MM 18.70 A 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 P1 RELEASE DATE 11 2019/10/18 10 INCH ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:26:00 9 8 7 6 5 EC NO: 625546 2017/08/12 2019/10/18 2019/10/18 DRWN: CMN CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: DROSCA APPR: JCOMERCI THIRD ANGLE PROJECTION 4 SPOX BMI 1X7 PLUG HOUSING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/03/29 2010/10/29 DRAWING SERIES C-SIZE 46831 3 SD-46831-002 MATERIAL NUMBER PSD 001 CUSTOMER 468310002 GENERAL MARKET 2 B SHEET NUMBER 1 OF 2 1 A 12 11 10 9 8 7 5 6 4 3 2 1 PLUG 1.00 MAX. RECEPTACLE TO PLUG MISALIGNMENT 2.50 ±0.15 H 10.44 R 0.20 3.12 ±0.15 (4 PLACES) R 3.38 H 2.10 ±0.15 1.00 MAX. RECEPTACLE TO PLUG MISALIGNMENT 11.16 G G 6.51 13.01 5.38 7.46 RECEPT 9.81 F F 18.39 PANEL CUTOUT WIRE ENTRY SIDE VIEW PANEL THICKNESS 1.00mm +/-0.15 WIRE SIDE ENTRY E E RECEPT PLUG D D SEE NOTE #1 13.54 +2.00 0 WIRE SIDE ENTRY PLUG & RECEPT SEE NOTE #1 C C +/- 0.48 2.70 ±0.48 PANEL TO PANEL ALIGNMENT (BOTH DIRECTIONS) PANEL TO PANEL STACK HEIGHT B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION NOTES: DIMENSION UNITS SCALE MM 2:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A 1. TO ALIGN 46831 PANEL CUTOUT WITH 46528 PANEL CUTOUT, ALIGN HORIZNONTAL CENTERLINES AND KEEP 2.70MM BETWEEN VERTICAL CENTERLINES OF THE PANEL CUTOUT IN THE DRAWING SD-46528-077. 2. TERMINALS MUST BE ALLOWED TO FLOAT FREELY WITHIN EACH CORE DO NOT TIE WIRES TOGHETER TIGHTLY, ALLOW WIRE TO MOVE. DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 P1 RELEASE DATE 11 2019/10/18 10 MM INCH 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:26:00 9 8 7 6 5 EC NO: 625546 2017/08/12 2019/10/18 2019/10/18 DRWN: CMN CHK'D: ISHWARG APPR: ISHWARG INITIAL REVISION: DRWN: DROSCA APPR: JCOMERCI THIRD ANGLE PROJECTION 4 SPOX BMI 1X7 PLUG HOUSING PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2010/03/29 2010/10/29 DRAWING SERIES C-SIZE 46831 3 SD-46831-002 MATERIAL NUMBER PSD 001 CUSTOMER 468310002 GENERAL MARKET 2 B SHEET NUMBER 2 OF 2 1 A