0527451633

10 9 7 8 6 5 4 3 1 注記NOTES 　1.使用材料 MATERIAL ハウジング：ポリアミド(PA)、ガラス充填、UL94V-0、ナチュラル(白) HOUSING:POLYAMIDE,GLASS FILLED,UL94V-0,NATURAL（WHITE） アクチュエータ：ポリフェニレンサルファイド（PPS）、ガラス充填、UL94V-0、黒 ACTUATOR:POLYPHENYLENE SULFIDE,GLASS FILLED,UL94V-0,BLACK ターミナル：リン青銅、(t=0.2) TERMINAL:PHOSPHOR BRONZE 金具：リン青銅、（t=0.2） FITTING NAIL:PHOSPHOR BRONZE 2.めっき仕様 PLATING ターミナル TERMINAL 錫銀ビスマスめっき(1.0μｍ以上) 下地：ニッケルめっき(1.0μｍ以上) TIN SILVER BISMUTH PLATING (1.0 MICROMETER MINIMUM) UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM) 金具 FITTING NAIL 錫めっき(1.0μｍ以上) 下地：ニッケルめっき(1.0μｍ以上) TIN PLATING (1.0 MICROMETER MINIMUM) UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM) 　3.エンボステープ梱包時は、アクチュエータがロックした状態になります。 IN THE PACKAGE,ACTUATOR SHOULD BE LOCKED. 4 偶数極に適用 APPLY FOR EVEN CIRCUIT. 5 ﾊﾟﾀｰﾝ剥離止め金具 FITTING NAIL FOR PREVENTION OF PEELING OF P.W.B. PATTERN. 6 R0.3は、FPCの導体部にかからないこと R0.3 MUST NOT BE OVERLAPED TO PATTERN OF FPC. 7 ソルダーテール方向のズレ量、及び金具半田付け面のずれ量は、 H 基準面　　に対し上方向0.1 MAX、下方向0.15MAXとする。 MISALIGNMENT OF SOLDER TAILS AND FITTING NAILS FROM H UPPER DIRECTION 0.1 MAX., LOWER DIRECTION 0.15 MAX. 8.ELV及びRoHS適合品 ELV AND RoHS COMPLIANT. F E D C K 5 B 2 7 金具 FITTING NAIL 0.85 1.28 DOCUMENT STATUS 10.65 9.65 9.15 8.65 8.15 7.65 7.15 6.65 6.15 5.65 5.15 4.65 4.15 3.65 2.65 9.5 8.5 8 7.5 7 6.5 6 5.5 5 4.5 4 3.5 3 2.5 1.5 52745-2033 52745-1833 52745-1733 52745-1633 52745-1533 52745-1433 52745-1333 52745-1233 52745-1133 52745-1033 52745-0933 52745-0833 52745-0733 52745-0633 52745-0433 D C B (A) EMBOSSED PACKAGE ORDER No. オーダー番号 20 18 17 16 15 14 13 12 11 10 9 8 7 6 4 D C B 極数 CKT. CONNECTOR SERIES NO. : 52745-**22 0.74 0.66 P1 RELEASE DATE 9 GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　±　3　° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS VIEW K (金具部投影図) 2.455 FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 14.3 13.3 12.8 12.3 11.8 11.3 10.8 10.3 9.8 9.3 8.8 8.3 7.8 7.3 6.3 E THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 1.02 A 16.1 15.1 14.6 14.1 13.6 13.1 12.6 12.1 11.6 11.1 10.6 10.1 9.6 9.1 8.1 F (DETAIL OF FITTING NAIL) 2022/11/03 08:33:25 8 7 6 5 DIMENSION UNITS SCALE mm 10:1 CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 0.5MM FPC CONN ZIF R/A HOUSING ASSY (UPPER CONTACT) EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/20 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/06 2013/03/15 DRAWING SERIES A3-SIZE 52745 3 SD-52745-055 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 GENERAL MARKET B1 SHEET NUMBER 1 OF 2 1 A 7 8 5 6 0.5(N+1)±0.07 0.5(N+1)±0.07 0.5±0.1 0.5±0.05 0.35+0.04 -0.03 0.5(N-1)±0.05 0.3±0.03 6±0.5 4±0.5 適合FFC推奨寸法 　　 　APPLICABLE FFC PLATING RECOMMENDED DIMENSION 仕上がり厚さ：0.3±0.03 仕上がり厚さ：0.3±0.03 THICKNESS: 0.3+0.03/-0.03 THICKNESS: 0.3+0.03/-0.03 0.5(N-1)±0.05 D (0.3) SOLDERING AREA OF FITTING NAIL L M コネクタ位置 CONNECTOR POSITION DETAIL L (0.2) 金具パターンエリア (0.3) (0.3) C 3.05 0.8 0.5±0.05 (PITCH) (NON-ACCUMULATIVE) 2.2 (0.3) 0.6MAX. 1.94MIN. 0.45MAX. 3.65 補強板：ポリイミド REINFORCE BOARD: POLYMIDE 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド(25μm) BASE FILM: POLYIMIDE(25μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 3.65 1.25 1.25 1.1 推奨基板レイアウト(マウント面) FPC構成推奨仕様 FFC構成推奨仕様 RECOMMENDED STRUCTURE OF FPC RECOMMENDED STRUCTURE OF FFC マスク厚　　:100μm マスク開口率：100% SCREEN THICKNESS : 100μm SCREEN OPEN TATIO : 100% PATTERN R0.303 BOARD GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　±　3　° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS VIEW M (DETAIL OF FITTING NAIL ON PATTERN) DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/11/03 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION (0.605) (FROM PATTERN EDGE) A C FPC/FFCについて： 　 抜き方向は、導体側から補強板側を推奨致します。 　 尚、接着剤の接点部への付着は導通不良の原因になりますので、 　 染み出しが無い様お願い致します。 ABOUT FPC/FFC: RECOMMENDED PUNCHER DIRECTION: FROM CONDUCTOR SIDE TO STIFFNER SIDE PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND BECAUSE THERE IS A POSSIBILITY THAT THE EXTRA ADHESIVE　 CAUSES THE　DEFECT IN ELECTRICAL CONTINUITY. RECOMMENDED P.C.BOARD PATTERN DIMENSION (MOUNTING SIDE) B カバーレイ　:　ポリイミド(25μm) COVER FILM: POLYIMIDE(25μm) D E 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 　　　 APPLICABLE FPC PLATING RECOMMENDED DIMENSION めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) 6 適合FPC推奨寸法 KEEPING OUT AREA OF PATTERN AND SOLDERING F 0.5±0.08 めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) E 仕上がり厚さ THICKNESS 0.5±0.05 補強板 (STIFFENER BOARD) 6±0.5 4±0.5 R0.3 1 0.3 ±0.03 仕上がり厚さ THICKNESS (PITCH) パターンおよび 半田禁止エリア 2 0.3 ±0.03 0.5±0.08 (PITCH) 3 補強板 (STIFFENER BOARD) 0.5(N-1)±0.05 0.5±0.1 F 4 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) 9 補強板：ポリエステル系 REINFORCE BOARD: PET 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 10 08:33:25 8 7 6 5 DIMENSION UNITS SCALE mm 5:1 CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 0.5MM FPC CONN ZIF R/A HOUSING ASSY (UPPER CONTACT) EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/20 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/06 2013/03/15 DRAWING SERIES A3-SIZE 52745 3 SD-52745-055 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 GENERAL MARKET B1 SHEET NUMBER 2 OF 2 1 A 10 9 8 7 6 5 4 3 2 1 F F 　 　　　 　　 E E D D カバーテープの剥離強度については、IEC60286-3 に準拠 COVER TAPE PEEL FORCE IS DEFINED BY IEC 60286-3. C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) ±0.2 10UNDER A 10 OVER P1 RELEASE DATE 9 2022/11/03 08:33:25 8 30 UNDER ±0.25 ±0.3 30 ANGULAR ±3° OVER DOCUMENT STATUS SCALE mm NTS CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) 6. ELV及びRoHS適合品 ELV　AND RoHS COMPLIANT FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 DIMENSION UNITS 7 6 5 ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 EMBOSS TAPE PACKAGED FOR 0.5MM FPC CONN ZIF R/A HOUSING ASSY EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/05 2013/03/15 DRAWING SERIES A3-SIZE 52745 3 SD-52745-056 MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 001 A SHEET NUMBER 1 OF 3 1 A 10 9 8 7 6 5 4 3 2 1 F F E E D D C C B B EMBOSSED PACKAGE ORDER No. CONNECTOR SERIES NO. : 52745-**22 オーダー番号 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) GENERAL TOLERANCES (UNLESS SPECIFIED) ±0.2 10UNDER A 10 OVER DOCUMENT STATUS P1 RELEASE DATE 9 2022/11/03 08:33:25 8 ±0.25 ±0.3 30 ANGULAR ±3° OVER FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 30 UNDER 7 6 5 ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 EMBOSS TAPE PACKAGED FOR 0.5MM FPC CONN ZIF R/A HOUSING ASSY EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/05 2013/03/15 DRAWING SERIES A3-SIZE 52745 3 SD-52745-056 MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 001 A SHEET NUMBER 2 OF 3 1 A 10 9 8 7 6 5 4 3 2 1 F F E E D D C C B B EMBOSSED PACKAGE ORDER No. オーダー番号 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) GENERAL TOLERANCES (UNLESS SPECIFIED) ±0.2 10UNDER A 10 OVER DOCUMENT STATUS P1 RELEASE DATE 9 2022/11/03 08:33:25 8 ±0.25 ±0.3 30 ANGULAR ±3° OVER FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 30 UNDER 7 6 5 ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 EMBOSS TAPE PACKAGED FOR 0.5MM FPC CONN ZIF R/A HOUSING ASSY EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/05 2013/03/15 DRAWING SERIES A3-SIZE 52745 3 SD-52745-056 MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 001 A SHEET NUMBER 3 OF 3 1 A