0621005300

Extraction Tool for Z-Power Module Z-Power Extraction Tool Instruction Sheet Order No. 62100-5300 FEATURES Œ Œ CLAMPING SCREW AND WASHER Lightweight tool used in the Extraction a Z-Power Module in a PCB Removes connector without damage to the board SCOPE Products: Z-Power 76001 Series. See Product List below for specific application tools. LIFTING JAW SPACER Product List SIDE GUIDE PLATE (2) LIFTING The following is a partial list of the product order numbers and their specifications JAW (2) this tool is designed to run. Updates to this list are available on www.molex.com. Assembly Order Number Description 76001-0006 Z-Power 6 Tail Assembly 76001-0010 Z-Power 10 Tail Assembly #10-32 SHCS DESCRIPTION The following Instructions are used for removing a Z-Power Module from a PCB. Operation Note: Be sure that all parts of the extraction tool will clear any components on the printed circuit board during use. Tape may also be placed over circuit traces or on the bottom of the extraction tool side guide plates for added protection of the printed circuit board. 1. Turn the #10-32 SHCS counter-clockwise (CCW) until half the lifting jaws are exposed below the side guide plates. Continue turning the #10-32 SHCS so the lifting jaw spacer is parallel to the power module. See Figure 2. Doc No. ATS-621005300 Revision: A Figure 1 Release Date: 11-24-06 Revision Date: 12-22-06 SPACER PLATE LIFTING JAW SPACER SIDE GUIDE PLATES PCB Z-POWER MODULE LIFTING JAWS UNCONTROLLED COPY LIFTING JAWS SNAP INTO THE SLOTS OF THE POWER MODULE Figure 2 Page 1 of 3 Extraction Tool for Z-Power Module 2. Slide the lifting jaws down over the power module until the lifting jaws lock onto the slots at the base of the power module. Note: The lifting jaws must snap into the slots of the power module so it can be lifted off the printed circuit board. 3. Turn the #10-32 SHCS clockwise (CW) until the extraction tool side guide plates contact the printed circuit board. Continue turning the #10-32 SHCS so the lifting jaw spacer is parallel to the power module. See Figure 3. 4. Continue turning the #10-32 SHCS until the power module is removed from the printed circuit board. See Figure 4. #10-32 SHCS #10-32 SHCS TURM (CW) LIFTING JAW SPACER CLOSED LIFTING JAW SPACER OPEN PCB PCB Z-POWER MODULE LIFTED OFF THE PCB Z-POWER MODULE SIDE GUIDE PLATES FLUSH WITH THE PCB Figure 3 Figure 4 5. Move the extraction tool away from the printed circuit board, then remove the power module from the extraction tool by turning the extraction tool on its side and slide the power module out. Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. 4. When tool is not in use, store in a clean, dry area. CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling. Doc No. ATS-621005300 Revision: A Release Date: 11-24-06 Revision Date: 12-22-06 UNCONTROLLED COPY Page 2 of 3 Extraction Tool for Z-Power Module PARTS LIST Item Order No Description Quantity 62100-5300 Extraction Tool for Z-Power (Figure 5) 1 62100-5301 Spacer Plate 1 2 62100-5303 Lifting Jaw Spacer 1 3 62100-5306 Lifting Jaw 2 4 62100-5308 Side Guide Plate 2 5 N/A #10 Washer Hardened 1** 6 N/A #4-40 by 3/16” Long SHCS 4** 7 N/A #6-32 by 5/16” Long SHCS 4** 8 N/A #10-32 by 1-3/8” Long SHCS 1** ** Available from an industrial supply company such as MSC (1-800-645-7270). Assembly Drawing 5 7 (4) 4 (2) 8 1 6 (4) 2 Figure 5 (2) 3 Americas Headquarters Far East North Headquarters Far East South Headquarters European Headquarters Corporate Headquarters -JTMF
*MMJOPJT

64"
:BNBUP
,BOBHBXB
+BQBO
+VSPOH
4JOHBQPSF
.VOJDI
(FSNBOZ

8FMMJOHUPO
$U
.0-&9



-JTMF
*-

64"
BNFSJOGP!NPMFYDPN
GFOJOGP!NPMFYDPN
GFTJOGP!NPMFYDPN
FVSJOGP!NPMFYDPN

'BY
 Visit our Web site at http://www.molex.com Doc No. ATS-621005300 Revision: A Release Date: 11-24-06 Revision Date: 12-22-06 UNCONTROLLED COPY Page 3 of 3