0622018840

Impact™ Daughtercard Press-In Tool Impact™ Daughtercard Module Installation Press-In Tool Application Tooling Specification Sheet Order No. 62201-8840 FEATURES Lip provided for positive alignment to connector assembly. Tool provides uniform distribution of press force across entire pin array. May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools. SCOPE Products: Impact™ Daughtercard 85 Ohm Assembly 170340 Series, (4-Pair by 14 Column Assemblies). See Product List below for specific part numbers. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com. Series No. Guide Style Columns Open 14 170340-1014 170340-3014 Left 14 170340-3314 170340 170340-3614 170340-5014 Right 14 170340-5314 170340-5614 Assembly Order Number 170340-1024 170340-3024 170340-3324 170340-3624 170340-5024 170340-5324 170340-5624 170340-3114 170340-3414 170340-3714 170340-5114 170340-5414 170340-5714 170340-3124 170340-3424 170340-3724 170340-5124 170340-5424 170340-5724 170340-3214 170340-3514 170340-3814 170340-5214 170340-5514 170340-5814 170340-3224 170340-3524 170340-3824 170340-5224 170340-5524 170340-5824 WITH 62201-95XX RAIL Tool Setup Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1. ALONE Figure 1 Doc No: ATS-6220188408 Revision: A Release Date: 12-13-13 Revision Date: 12-13-13 UNCONTROLLED COPY Page 1 of 3 Impact™ Daughtercard Press-In Tool Tool Installation The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools. Rail Part Number Rail Overall Length 62201-9501 24mm (0.94 in) 62201-9502 72mm (2.83 in) 62201-9503 156mm (6.14 in) 62201-9504 216mm (8.50 in) 62201-9509 254mm (10.0 in) 62201-9511 305mm (12.0 in) Reference: This Press-In Tool is 26.46mm (1.04 in.) long. Printed Circuit Board (PCB) Support The Impact™ connectors require up to 3.6kg (8 lb) of force per pin to press into the PCB. To prevent excessive PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole pattern. Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must furnish their own support plate. When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through the PCB thickness. Press Equipment Recommendations Many types of presses can be used to install Impact™ connectors, but to assure consistent connector installation Molex recommends the following press criteria: 1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force measurements should stop the press-in cycle. 2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second. 3. Press stroke control to within 0.25mm (0.010 in). 4. Total press stroke must be at least 19mm (0.75 in). 5. For statistical purposes, automatic collection of force GUIDE SURFACE and distance data. Tool Operation 1. Carefully insert, by hand, the Daughtercard module(s) into the PCB hole pattern. 2. Place the application tool on top of the Daughtercard module with the back guide surface of the tool against the back of the Daughtercard module. See Figure 2. Figure 2 Doc No: ATS-6220188408 Revision: A Release Date: 12-13-13 Revision Date: 12-13-13 UNCONTROLLED COPY Page 2 of 3 Impact™ Daughtercard Press-In Tool 3. Using the application tool and an appropriate press, seat the Daughtercard module until there is less than 0.10mm (.004 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3. 0.10 .004 MAXIMUM Figure 3 There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing). CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press manufacturer’s instruction manual. CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling. Contact Information For more information on Molex application tooling please contact Molex at 1-800-786-6539. http://www.molex.com Doc No: ATS-6220188408 Revision: A Release Date: 12-13-13 Revision Date: 12-13-13 UNCONTROLLED COPY Page 3 of 3